Daikin Intelligent Touch Manager DCM601A71 User manual

User’s Manual
Model
DCM601A71
DCM601A72
DCM601A73
DCM002A71
DCM008A71
MONITOR
CPU ALIVE
SLAVE
MASTER
BACKUP
LAN SW
SERVICE LAN
FRONT BACK
DMASTER
ON
OFF RESET
LAN LINK
D MONITOR

1
Disclosure
To the User in USA
Part 15 of FCC
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
To the User in CANADA
Canadian ICES-003
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
2
Safety Considerations
Read these SAFETY CONSIDERATIONS carefully before operating the controller.
Train the customer to operate and maintain the controller.
Inform customers that they should store this User’s Manual with the Installation Manual for future
reference.
Meanings of WARNING, CAUTION and NOTE Symbols:
WARNING Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTE Indicates situation that may result in equipment or property-damage only
accidents.
•The following pictograms are used in this manual.
Never do. Always follow the instructions given.
Keep wet hands away. Keep water and moisture away.
WARNING
•Do not modify or repair the controller.
Consult your Daikin dealer for any modication or for repairs.
•Do not relocate or reinstall the controller by yourself.
Improper installation may result in electric shocks or re.
Consult your Daikin dealer to relocate or for any reinstallation.
•Do not use ammable materials (e.g., hairspray or insecticide) near the
controller.
Do not clean the product with organic solvents such as paint thinner.
The use of organic solvents may cause cracking, damaging the product, causing elec-
tric shocks, or re.
•Consult the dealer if the controller was submerged under water due to a
natural disaster, such as a ood or hurricane.
Do not operate the controller if it was submerged under water or a mal-
function, electric shock, or re can occur.

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
3
CAUTION
•Never disassemble the controller.
Touching the interior parts may result in electric shocks or re.
Consult your Daikin dealer for internal inspections and adjustments.
•Do not allow children to play with the controller to avoid causing damage
to the product.
•Do not touch the controller buttons with wet ngers.
Touching the buttons with wet ngers can cause an electric shock.
•Do not wash the controller.
Doing so may cause electric leakage and result in electric shocks or re.
•Never let the controller to get wet.
Water can cause damage to the controller, and may cause an electric shock or re.
NOTE
•Never press the button of the controller with a hard, pointed object.
The controller may be damaged.
•Never pull or twist the electric wire of the controller.
It may cause the unit to malfunction.
•Do not wipe the controller operation panel with benzine, thinner, chemical
dustcloth, etc.
The panel may get discolored or the coating peeled off. If it is heavily dirty, soak a
cloth in water-diluted neutral detergent, squeeze it well and wipe the panel clean. And
wipe it with another dry cloth.

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
4
Contents
Safety Considerations....................................................................2
System Overview............................................................................8
1. About the iTM (intelligent Touch Manager)......................................................8
1-1 Main Features..................................................................................................................... 8
1-2 System Conguration ......................................................................................................... 9
1-3 What is a Management Point/Area? ................................................................................. 10
•What is a management point? ...................................................................................... 10
•What is an area?........................................................................................................... 10
1-4 Touch Panel Operation Method ........................................................................................ 12
1-5 Dialog Operation............................................................................................................... 16
•Text /Password input dialog operation .......................................................................... 16
•Time input dialog operation........................................................................................... 19
•Numerical input dialog operation .................................................................................. 20
Quick Reference ...........................................................................22
2. Simple Operations ...........................................................................................22
2-1 Displaying the List of Areas and Management Points ...................................................... 22
2-2 Displaying Areas and Management Points ....................................................................... 22
2-3 Starting/Stopping Areas and Management Points............................................................ 23
2-4 Setting up the Operation Mode for an Indoor Unit ............................................................ 24
2-5 Setting up the Setpoint, Fan Speed, and Airow Direction for an Indoor Unit .................. 25
2-6 Enabling/Disabling Remote Controller.............................................................................. 27
2-7 Setting up the Operation Mode and Ventilation Amount for Ventilator .............................. 28
2-8 Performing Operations with the Menu List Screen ........................................................... 28
•Checking the schedule.................................................................................................. 29
•Checking settings such as Area Name, Detailed Info., and Icon .................................. 30
•Checking settings such as Mgmt. Point Name, Detailed Info., and Icon ....................... 30
•Setting up the time........................................................................................................ 31
•Checking the history ..................................................................................................... 32
Names and Functions ..................................................................33
3. Names and Functions of Each Part................................................................33
3-1 Front Panel and Side View................................................................................................ 33
Contents

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
5
4. Detailed Screen Description ...........................................................................35
4-1 Setup Screen Structure .................................................................................................... 35
4-2 Standard View (Icon) Screen ............................................................................................ 37
•Detailed Setup Screen.................................................................................................. 40
•Detailed Information Screen ......................................................................................... 46
4-3 Standard View (List) Screen ............................................................................................. 47
4-4 Layout View (Optional) Screen ......................................................................................... 50
4-5 Menu List Screen.............................................................................................................. 52
•Automatic Ctrl. Tab ........................................................................................................ 52
•System Settings Tab ..................................................................................................... 54
•Operation Mgmt. Tab..................................................................................................... 56
•Energy Navigator Tab.................................................................................................... 57
4-6 Information Screen ........................................................................................................... 58
•Legend Tab ................................................................................................................... 58
•Contact Tab ................................................................................................................... 60
Using Standard Functions...........................................................61
5. Setting up the Automatic Control...................................................................61
5-1 Setting up a Schedule....................................................................................................... 61
•Setting up a schedule program ..................................................................................... 61
•Detailed screen and button descriptions....................................................................... 72
5-2 Setting up the Timer Extension Function.......................................................................... 97
5-3 Setting up the Auto Changeover....................................................................................... 99
•Creating and editing an Auto Changeover group........................................................ 101
•Setting up the changeover conditions......................................................................... 103
•Applying the Auto Changeover function...................................................................... 105
5-4 Checking an Emergency Stop ........................................................................................ 107
6. System Settings .............................................................................................109
6-1 Setting up an Area.......................................................................................................... 109
•Creating and deleting an area..................................................................................... 109
•Moving an area ........................................................................................................... 113
•Registering a management point or area to an area .................................................. 114
•Naming and setting up the detailed information of an area ........................................ 117
•Setting up the interval for sequential start/stop........................................................... 118
•Setting up icons .......................................................................................................... 119
• Saving and loading the area data CSV le ................................................................. 120
6-2 Setting up a Management Point ..................................................................................... 121

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
6
6-3 Setting up and Changing the Password.......................................................................... 123
6-4 Setting up Maintenance and Checking........................................................................... 125
6-5 Setting up and Changing the Locale............................................................................... 126
6-6 Setting up and Changing the Time ................................................................................. 128
6-7 Setting up and Changing the Screensaver ..................................................................... 129
6-8 Setting up and Changing the Hardware Settings............................................................ 130
6-9 Setting up and Changing the Conrm Operation............................................................ 131
6-10 Calibrating the Touch Panel ......................................................................................... 132
6-11 Backing up ................................................................................................................... 133
6-12 Viewing the Version Information................................................................................... 134
7. Data Management ..........................................................................................135
7-1 Checking and Outputting History.................................................................................... 135
7-2 Outputting Function Settings .......................................................................................... 137
Operating Optional Functions...................................................147
8. Setting up Automatic Control Functions .....................................................147
8-1 Setting up the Setback.................................................................................................... 147
8-2 Setting up the Interlocking Control.................................................................................. 153
•Interlocking Control Restrictions ................................................................................. 156
•Setting up an interlocking program ............................................................................. 158
•Detailed screen and button descriptions..................................................................... 166
8-3 Setting up the Emergency Stop...................................................................................... 188
•Releasing the Emergency Stop .................................................................................. 191
8-4 Setting up the Temperature Limit.................................................................................... 192
8-5 Setting up the Sliding Temperature Function.................................................................. 197
8-6 Setting up the Heating Mode Optimization Function ...................................................... 203
9. System Settings .............................................................................................205
9-1 Network Settings ............................................................................................................ 205
9-2 Web Access Settings and Remote Management ........................................................... 208
•Registering Web users................................................................................................ 209
•Logging in/out to/from a PC ........................................................................................ 212
•Web Remote Management Screen............................................................................. 213
9-3 Setting up the E-Mail Error Report ................................................................................. 216
•Setting up the Mail Server........................................................................................... 216
•Setting up the recipient E-mail address and sending an E-mail ................................. 219

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
7
Operating Optional Maker Functions .......................................223
10. Power Proportional Distribution ...............................................................223
10-1 Power Proportional Distribution Function .................................................................. 223
•Setting up the data collection period........................................................................... 223
•Collecting data and outputting the Power Proportional Distribution results ................ 224
11. Energy Navigator........................................................................................226
11-1 Energy Navigator Function ........................................................................................ 226
•Energy Budget/Actual Management........................................................................... 229
•Equipment operation management (Deviation from the operation plan)..................... 249
•Data output function.................................................................................................... 265
iTM integrator Explanation ........................................................273
12. iTM integrator..............................................................................................273
12-1 iTM integrator ............................................................................................................ 273
•Detailed screen and button descriptions..................................................................... 274
•Cautions when using the iTM integrator ..................................................................... 282
Maintenance................................................................................286
13. Maintenance................................................................................................286
13-1 Resetting the Filter Sign ............................................................................................ 286
13-2 Maintaining the LCD display...................................................................................... 287
Useful Information......................................................................288
14. Troubleshooting..........................................................................................288
14-1 Before Having the Product Serviced ......................................................................... 288
14-2 Turning ON/OFF the Internal Battery......................................................................... 299
14-3 Error Information Function......................................................................................... 300
15. Hardware Specications............................................................................302
15-1 iTM Hardware Specications..................................................................................... 302
15-2 Peripheral Equipment Specications......................................................................... 303
15-3 Copyright and Trademarks......................................................................................... 303
Appendix .....................................................................................304

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
8
1. About the iTM (intelligent Touch Manager)
1-1 Main Features
• iTM is an advanced central controller operated by using a 10.4” touch panel. It allows you to easily monitor
as well as operate air conditioners and generic equipment connected to the iTM from the touch panel.
•One iTM can monitor and control a maximum of 64 groups of indoor units (128 units), including
Ventilator. The iTM can be expanded with up to seven iTM plus adaptors, which similarly to the
iTM, can connect a maximum of 64 groups of indoor units (128 units); that is, with one iTM you
can control and monitor a maximum of 512 groups of indoor units (1024 units).
A group of indoor units refers to the following:
(1) One indoor unit without remote controller
No remote controller
Indoor unit
(2) One indoor unit controlled with one or two remote controllers
Remote controller Remote controller
or
(3) Up to 16 indoor units controlled as group with one or two remote controllers
Up to 16Up to 16 Two remote controllerRemote controller
• The iTM allows you to dene privileges for Users and Managers, so that you can set up and manage them according
to their respective privileges. Furthermore, by connecting the iTM with computers in a LAN, you can set up Web
Remote Management and allow a maximum of 4 managers and 16 users to simultaneously access the iTM, and if a
connection to the Internet is available, then, you can monitor and operate the iTM remotely, via the Internet.
•The iTM allows you to schedule the operation of each air conditioner in detail.
You can set up an annual schedule by setting up a schedule by the day of the week and dening
Special Days such as extra holidays.
Changes by the season are achieved by setting up a validity period to programs.
•
By using optional functions, you can display the oor plan of individual buildings and the like as background
on the iTM monitoring screen, and monitor and operate by viewing the actual layout of the air conditioners.
•You can use Interlocking Control to start/stop air conditioners in conjunction with other equipment
or Setback function to save energy.
•
You can use Power Proportional Distribution function (option software) to distribute the electric bill among
tenants or the Energy Navigator function (option software) to manage the energy consumption systematically.
•By connecting a USB memory to the iTM, you can output billing data, budget/actual energy
consumption data, function settings, history data, etc. to a CSV le.
•Periodical data saving is recommended in order to prevent loss of your important data due
to an accidental problem.
NOTE
System Overview

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
9
1-2 System Conguration
USB memory
Di/Pi port
. . .
RS485
(Expansion
adapter port)
Di/Pi port
D3net
Up to 7
D3net port
Port 1~4:
Port 1:
Port 2~4:
Up to 64 groups
LAN port
ROUTER
Web Remote Management
HUB/SWITCH/ROUTER/....
Web Remote Management
Web Remote Management possible from network-
connected PC
Maximum 4 administrators and 16 users can log in
at the same time
USB port
iTM
Emergency Stop signal input
Power meter pulse input
Input signal (contact) such as
power outage signal
Emergency Stop signal input
Power meter pulse input
Input signal (contact) such as
power outage signal
iTM
plus adaptor
iTM
plus adaptor
iTM
plus adaptor
iTM
plus adaptor
iTM
plus adaptor
iTM
plus adaptor
Intranet/Internet

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
10
1-3 What is a Management Point/Area?
What is a management point?
A management point is the target equipment monitored and operated using the iTM.
The types of management points that can be controlled by iTM are as follows:
Indoor, Ventilator, Dio, Analog, Pulse, and Outdoor, Chiller
What is an area?
An area is a hierarchical group into which management points, monitored and operated by the iTM,
are classied. You can populate an area with member areas and management points. An All area,
to which you cannot manually register or delete members from, is provided by default.
Maximum number of areas that can be created: 650 (All excluded)
Example:
Total number of
management points
that can be registered
in Top areas :
1300 (All excluded)
All
Top
Lavatory
Lavatory Indoor unit
All Area
1 F
1 F
Indoor unit
Office indoor unit
Levels Level 1 2 3
Area Management point
Meeting room indoor-unit
Maximum number
of management
points and areas
that can be
registered in
one area : 650
Meeting room
Maximum number of hierarchal levels that can be created: 10 levels
Registered management points are automatically registered in the folder for the corresponding
management point type set up under All.
NOTE

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
11
You can register a management point in two or more areas. However, you cannot register the same
management point two or more times in one area. You cannot register the same area in two or
more areas either.
Area Management point
1F North
Building A
1F South
Meeting
Room
Level 1 Level 2 Level 3 Level 4 ... Level 10
Management point A
Aisle
Management point A
Management point A
Aisle
All
Top
Indoor
Ventilator
Dio
Analog
Pulse
Outdoor
Chiller
Meeting
Room A
Example:
•Registered manage-
ment points automati-
cally belong to an
area based on their
type.
•Areas with manage-
ment points of non-
existing types are not
displayed.
Areas/Management
points displayed when
Top is touched.
The same manage-
ment point cannot be
registered with the
same area.
The same area cannot
be registered repeatedly.

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
12
1-4 Touch Panel Operation Method
Operation is possible by touching the panel with your ngers or a touch pen. Be sure not to use
sharp edged items as this could damage the touch screen permanently.
(3)
(1)
(3)
(3)
(2)
(8)
(6)
<Standard View (Icon) Screen>
(5)
(4)
(5)
(7)
)
<Detailed Setup dialog>
The following describes how the text on each component, displayed on screen, looks like in normal
state, when it is selected (it has been touched), or is grayed out. (* For components not shown in
the Standard view above, see the respective detailed description page.)

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
13
(1) Icon of centrally monitored management point/area
Unselected status Selected status
(2) List, scroll bars, and sorting
List image
•Scroll bars appear when there are hidden lines and columns.
•To display hidden lines and columns, press , or slide the scroll bars.
•To display truncated column text, slide the column separation.
•When sorting is enabled, touch the header to sort the column according to the sequence shown
in the gure below
Initial state Ascending order Descending order
(3) Button
Normal status Pressed status Grayed out status
With tool tip

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
14
•Components such as buttons and check boxes are grayed out when not all the conditions for
operating the particular function/option for the management point/area are satisfied.
Operation, such as touch and select a grayed out component, is not possible.
•“...” is displayed on buttons and the like when the label text is truncated due to space
availability.
To display the label text completely, touch the component for a while. A tool tip with the
complete text will appear.
NOTE
(4) Radio button
Selected status Unselected status Grayed out status
With tool tip
(5) Check box
Selected status Unselected status Grayed out status
With tool tip

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
15
(6) Combo box
Closed status Grayedout statusWith tool tip
Open status
When the list opens downward
Open status
When the list opens upward
Open status
(When a row is selected)
(7) Text box
Text box (When unfocused) Text box (When focused)
Cursor
Indicates the position where the next character
will be entered.
(8) Spin box
Closed status Grayed out status
Open status
(When the
minimum value
is selected)
(When the
maximum value
is selected)
(When an
intermediate value
is selected)

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
16
1-5 Dialog Operation
Text /Password input dialog operation
(2)
(1)
(6) (4)
(7) (8)
(3)
(5)
(1) Character key buttons
Key buttons for entering characters.
(2) Input area text box
Displays the entered characters. For the Password input dialog, it displays asterisks (*).
(3) Shift key toggle button
Toggles between upper and lower case.
Shift key
pressing
Shift key
pressing
(4) Right and left arrow buttons
Moves right and left the cursor in the input area text box.

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
17
(5) Character input range label
Displays three types of information regarding the number of characters that can be entered.
Remaining: Indicates the difference between the number of characters entered and the maximum
permitted by the function
Exceeded: Indicates the number of characters entered in excess from the maximum permitted
Missing: Indicates the number of characters still necessary to comply with the minimum required
(6) Keyboard switch combo box
Toggles the keyboard between Special and Alph nm ltrs.
Special: Sets the keyboard to special keyboard
Alph nm Itrs: Sets the keyboard to alphanumeric keyboard
Not displayed for the Password input dialog.
To toggle between upper and lower case, use the Shift key.
Shift key
pressing
Shift key
pressing
(7) OK button
Touching this button commits the input.
(8) Cancel button
Touching this button cancels the edit and closes the screen.

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
18
•Grayed out characters are unavailable for input.
•When Chinese, Japanese or Korean is set as the iTM display language, a button to display
the input list appears. Touch the button to display a list of frequently used words and select
the word to input. Select a word and commit the selection by pressing the OK button. The
selected word is displayed in the input area text box. Not displayed for the Password input
dialog.
NOTE

User’s Manual EM11A017
DCM601A71 intelligent Touch Manager
19
Time input dialog operation
(1)
(5)
(3)
(7)(6)
(4)
(2)
(1) Number key button
Key buttons for entering numeric values.
(2) Input area text box
Displays the entered numeric values. Touch the text box and enter the required numeric value. The
input area text box changes the display pattern among “year month day hour minute second”, “year
month day”, and “hour minute” depending on the entered data.
(3) Up/Down button
Increases or decreases the numeric value selected in the input area text box (2) by +1, +10, –1, or
–10.
(4) AM/PM setting combo box
Species whether the time is AM or PM when time is indicated using 12-hour clock. This combo
box is not displayed when 24-hour clock is set in the System Settings.
(5) Input range label
Displays the range of values that can be entered.
(6) OK button
Touching this button commits the input.
(7) Cancel button
Touching this button cancels the edit and closes the screen.