Daikin ARC417A14 User manual

ARC417 Series Si10-416A
80 Remote Controllers
ARC417A14, A15
Open
the
cover.
MODE
FAN
CANCEL
ON/OFF
TEMP
SWING
OFF TIMER
TIME
ON TIMER
UP
DOWN
POWERFUL
SILENT
HOME LEAVE
1
2
5
8
9
12
4
3
6
7
10
13
14
11

Si10-416A ARC417 Series
Remote Controllers 81
1. Transmitter
It sends signals to the indoor unit.
2. ON/OFF button
Press it once to start operation. To stop it, press it
once again.
3. Display
It displays the current settings.(In this illustration, each
section is shown with all its displays ON for the
purpose of explanation.)
4. TEMPERATURE / TIME adjustment buttons
It changes the temperature or time setting.
5. CLOCK button
6. OFF TIMER button
7. ON TIMER button
8. TIMER CANCEL button
It cancels the timer setting.
9. FAN setting button
It selects the air flow rate setting.
10. MODE selector button
It selects the operation mode.
(AUTO / DRY / COOL / HEAT / FAN)
11. SWING buttons
12.OUTDOOR UNIT SILENT button
13. POWERFUL button
14. HOME LEAVE button
Indicator lamps
OPERATION lamp (green)
HOME LEAVE lamp (red)
TIMER lamp (yellow)
• Lights up when you use HOM
E
LEAVE Operation.
ON/OFF switch
Unit operation panel and display panel

ARC417 Series Si10-416A
214 Operation
3. ARC417 Series
3.1 Preparation Before Operation
Setting the batteries
2
3
1
1Press with a finger and slide the back
cover to take it off.
2Set two alkaline dry batteries (LR03).
3Set the back cover as before.
This will cause the figures on the display
to flash. Set the clock at this point.
Position + and
– correctly!
Address switch
Remote controller

Si10-416A ARC417 Series
Operation 215
Receiver
Operating the remote controller
To use the remote controller, aim the transmitter at
the indoor unit. If there is anything to block signals
between the unit and the remote controller, such as
a curtain, the unit will not operate.
Do not drop the remote controller. Do not get it wet.
The maximum distance for communication is about
7 m.
To remove, pull it upwards.
Remote controller
holder
Set.
Push.
1
2
To fix the remote controller
holder on the wall
Choose a place from where the signals reach
the unit.
Fix the holder to a wall, a pillar, etc. with the
screws supplied with the holder.
Fit the claw of the holder into the bottom of
the remote controller, and push the remote
controller onto the wall.
1
2
3

ARC417 Series Si10-416A
216 Operation
Setting the air purifying filters
Indoor unit
1
Open the front grille.
Hold the grille by the tabs on the two sides
and lift it until it stops with a click.
(about 60˚)
2
Pull out the air filters.
Push upwards the
tab at the center of
each air filter, then
pull it down.
3
Set the air purifying filters.
Attach an air purifying filter to each air filter.
4
Set the air filters in their original
positions and close the front grille.
Operation without air filters may result in
troubles as dust will accumulate inside the
indoor unit.

Si10-416A ARC417 Series
Operation 217
Setting the clock
Turn the breaker ON
1
Press .
Press .
blinks.
2
Press
3
present time.
rapidly increases or decreases the time display.
Holding down ( ) or ( ) button
Turning ON the breaker opens the flap, then
closes it again. (This is a normal procedure.)
to set the clock to the
is displayed.
blinks.

ARC417 Series Si10-416A
218 Operation
Be careful not to cool (heat) the room too much.
Keeping the temperature setting at a moderate
level helps save energy.
Cover windows with a blind or a curtain.
Blocking sunlight and air from outdoors
increases the cooling (heating) effect.
The air conditioner always consumes 15 – 35 watts of
electricity even while it is not operating.
If you are not going to use the air conditioner for a long
period, for example in spring or autumn, turn the breaker OFF.
Use the air conditioner in the following conditions.
(*1) Use in humidity 60 % or lower when using the unit at an
outdoor temperature of 10˚C or lower.
Clogged air filters cause inefficient
operation and waste energy. Clean them
once in about every two weeks.
For cooling: 26˚C – 28˚C
For heating:20˚C – 24˚C
NOTE
Tips for saving energy
Please note
Recommended temperature setting
Mode Operating conditions
Outdoor temperature 2A safety device may work to stop the
operation.
(In multi system, it may work to stop
the operation of the outdoor unit
only.)
2Condensation may occur on the
indoor unit and drip.
2A safety device may work to stop the
operation.
Indoor temperature : 18 to 32 ˚C
Indoor humidity : 80% max. (*1)
RKD, RXD, RMX : –5 to 46 ˚C
3MX : 21 to 43 ˚C
4MX : 10 to 43 ˚C
3MK, 4MK : 10 to 46 ˚C
RMK : 5 to 46 ˚C
Outdoor temperature
Indoor temperature : 10 to 30 ˚C
RKD, RXD : –15 to 24 ˚C
3MX, 4MX : –10 to 24 ˚C
RMX : –15 to 24 ˚C
If operation is continued out of this range
COOL/
DRY
HEAT

Si10-416A ARC417 Series
Operation 219
3.2 AUTO • DRY • COOL • HEAT • FAN
Operation

ARC417 Series Si10-416A
220 Operation

Si10-416A ARC417 Series
Operation 221