Daikin T sense ax1 Instruction Manual

Security

&

Home Automation System

QUICK USER &

INSTALLER MANUAL

(REVISION 2.0)

T Sense Keypad Quick User & Installer Manual Rev 2.0

ARM AND DISARM SYSTEM

Default Master Pin 111 111

QUICK ARM

ARM with PIN

DISARM With PIN

Auto Home

▪Press & hold button [1] for 2 seconds

If enable Partition Option

▪Press [1 or 2] + #

Press 1 for partition 1

Press 2 for partition 2

▪Press [Master PIN] + [#]

By default, keypad will arm partition

1 only

If enable Partition Option

▪Press [Master PIN] +[#]+[1 or 2]+[#]

Press 1 for partition 1

Press 2 for partition 2

▪Press [Master PIN] + [#]

If enable Partition Option

▪Press [Master PIN]+ [#] +[1 or 2] +[#]

Press 1 for partition 1

Press 2 for partition 2

Day

▪Press & hold button [2] for 2 seconds

If enable Partition Option

▪Press [1 or 2] + #

Press 1 for partition 1

Press 2 for partition 2

Night

▪Press & hold button [3] for 2 seconds

If enable Partition Option

▪Press [1 or 2] + #

Press 1 for partition 1

Press 2 for partition 2

Force

▪Press & hold button [4] for 2 seconds

If enable Partition Option

▪Press [1 or 2] + #

Press 1 for partition 1

Press 2 for partition 2

REMARKS

-Default Master PIN = 111111

-The ARMED LED (RED) is ON if the system is armed.

ENABLE PARTITION OPTION

Steps to Enable Partition Option

▪Press [▼] for 2 sec + [▼for PART] + [Press 1 to toggle] + [#]

REMARKS

-By default, partition option is disabled

AUTOMATION CONTROL

COMMAND

▪Press & hold button [5] for 2 seconds

▪Press the relevant module number (01 to 16) to toggle output

▪Press * to exit automation menu

REMARKS

-The keypad will beep twice upon confirmation or else, an error tone will sound.

- To on/off all output: [00] is pressed to toggle all output. System priority to turn OFF all output if there is any output is ON.

1

T Sense Keypad Quick User & Installer Manual Rev 2.0

CLEAR ALARM MEMORY

COMMAND

INFORMATION

▪Press & hold button [6] for 2 seconds

▪Clear Zones, Strobe Light & Ext Comm. Error

DOOR CHIME

COMMAND

▪Hold [7] for 2 sec + [Zone number 01 to 16] + [#]

REMARKS

-When door chime is activated, the keypad will sound each time the designed zone is triggered

SYSTEM SERVICE

COMMAND

INFORMATION

▪Press & hold button [8] for 2 seconds

▪Press the corresponding number to check the trouble

▪Press [*] to Exit

Zone 1 (AC Power Loss)

Zone 2 (Low Battery)

Zone 3 (External Communication Failure)

Zone 4 (Telephone Line Loss)

Zone 5 (Tamper Zone)

REMARKS

- Trouble LED (RED) is ON when there is system trouble

- Trouble LED is OFF when there is no system trouble

BYPASS ZONE AND RESTORED

BYPASS

ZONE RESTORE

▪Press & hold button [9] for 2 seconds

▪Press [Zone Number]

▪Press [#] to save and exit

Press [01] to [16] to select zone 1 to 16

Key in 2 digit

▪Press & hold button [9] for 2 seconds

▪Press [Zone Number]

▪Press [#] to save and exit

Press [01] to [16] to select zone 1 to 16

Key in 2 digit

REMARKS

- Press [01] to [16] to select zone 1 to 16 again in this menu in order to have quick BYPASS and ZONE RESTORE

- In the normal mode, bypass zone will blinking to show that zone is already bypass.

-Bypass zones are cleared after system is disarmed.

KEY LOCK

COMMAND

[COM] + [1] + [#]

REMARKS

-Key lock is design to avoid miss control by guest or kids.

- The “Key lock” icon on LCD will turn ON to indicate key lock is enabled and toggle based

PRECAUTION

-If user key in wrong password for 10x,the keypad will automatically lock by itself for 3 minutes

SERVICE

1 2 3 4 5

2

T Sense Keypad Quick User & Installer Manual Rev 2.0

KEYPAD SETTING

Keypad Setting

Command

Partition Option

Press [▼] for 2 sec + [▼for PART] + [Press 1 to toggle] + [#]

ON/OFF Keypad backlight

Press [▼] for 2 sec + [▼for LIGHT] + [Press 1 to toggle] + [#]

ON/OFF keypad Arm tone

Press [▼] for 2 sec + [▼for A TONE] + [Press 1 to toggle] + [#]

ON/OFF entry & exit delay buzzer tone

Press [▼] for 2 sec + [▼for E TONE] + [Press 1 to toggle] + [#]

ON/OFF key press tone

Press [▼] for 2 sec + [▼for K TONE] + [Press 1 to toggle] + [#]

Reset default setting

Press [▼] for 2 sec + [▼for RESET] + [#] + [Yes] + [#]

TESTING THE SYSTEM

TESTING

Command

Walk Test

Enter : Press and hold [▲] for 2sec + [▼for WALK] + [#]

Exit Walk Test : Press [#]

Bell Test

Press and Hold [▲] for 2sec + [▼for BELL] + [#]

CMS Test

Press and Hold [▲] for 2 sec + [▼for CMS] + [#]

Battery Test

Press and Hold [▲] for 2sec + [▼for BATT] + [#]

Identification Test

Press and Hold [▲] for 2 sec + [▼for IDEN] + [#]

Remark

Please refer to the identification test table

IDENTIFICATION TEST TABLE

[▲] / [▼] to scroll System Identification and IO Identification

System Identification

IO Identification

Zone number

Description

Zone number

Description

1

Keypad 1

1

Output 1

2

Keypad 2

2

Output 2

3

Keypad 3

3

Output 3

4

Keypad 4

4

Output 4

5

Keypad 5

5

Output 5

6

Keypad 6

6

Output 6

7

Keypad 7

7

Output 7

8

Keypad 8

8

Output 8

9

Voice

9

Output 9

10

AIM

10

Output 10

11

WSM

11

Output 11

12

Zone Expander 1

12

Output 12

13

IO Expander 1

13

Output 13

14

IO Expander 2

14

Output 14

15

-

15

Output 15

16

-

16

Output 16

IDENTIFICATION TEST TABLE

3

T Sense Keypad Quick User & Installer Manual Rev 2.0

USER PROGRAMMING SUMMARY Default Master Pin 111 111

Description

Command

Enter User Programming Mode

[Master Pin] + [COM] + [#]

Exit User Programming Mode

Press and Hold [*] for 2 sec

Edit Master Pin

[▼for Pin] + [#] + [▼for Master] + [#] + [New Pin] + [#] + [Re-enter Pin] + [#]

*Edit User 1 - 7 Pin

[▼for Pin] + [#] + [▼for User 1 - 7] + [#] + [New Pin] + [#] + [Re-enter Pin] + [#] +

[Access Level] + [#] + [Partition] + [#]

*Edit Guest Pin

[▼for Pin] + [#] + [▼for Guest] + [#] + [New Pin] + [#] + [Re-enter Pin] + [#] +

[Access Level] + [#] + [Partition] + [#] + [Valid Day] + [#]

* Remark [Access Level] –Refer to create/edit User 1 –7 Pin, Guest/Duress Pin

Authority for user code can be set according to details below:

Key [1] –Arm Enable (1)/ Disable (0), Key [2] –Disarm Enable (1)/ Disable (0)

Key [3] –Bypass Enable (1)/ Disable (0), Key [4] –Open/ Close Report (1)/ Disable (0)

Edit Duress Pin

[▼for Pin] + [#] + [▼for Duress] + [#] + [4 digit New Pin] + [#] + [Re-enter NEW PIN]

+ [#]

Program Clock

[▼for Timer] + [#] + [▼for Clock] + [#] + [Set Time] + [#]

**Program Arm Timer

[▼for Timer] + [#] + [▼for Arm] + [#] + [Set Time] + [#] + [Select Partition] + [#]

**Program Disarm Timer

[▼for Timer] + [#] + [▼for Disarm] + [#] + [Set Time] + [#] + [Select Partition] + [#]

**Remark [Select Partition] –Refer to Program Arm/Disarm Timer

User need to enable partition option to select partition. The steps as below:

Press [▼] for 2 sec + [▼for Partition Opt] + [Press 1 to toggle] + [#]

Delete Arm Timer

[▼for Timer] + [#] + [▼for Arm] + [#] + [0] + [#]

Delete Disarm Timer

[▼for Timer] + [#] + [▼for Disarm] + [#] + [0] + [#]

Program ON IO Timer

[▼for Timer] + [#] + [▼for IO On 1 - 4] + [#] + [Set Time] + [#] + [Output] + [#]

Program OFF IO Timer

[▼for Timer] + [#] + [▼for IO Off 1 - 4] + [#] + [Set Time] + [#] + [Output] + [#]

Delete ON IO Timer

[▼for Timer] + [#] + [▼for IO On 1 - 4] + [#] + [0] + [#]

Delete OFF IO Timer

[▼for Timer] + [#] + [▼for IO Off 1 - 4] + [#] + [0] + [#]

Program Personal Telephone

Number

[▼for Phone] + [#] + [▼for Phone 1 - 4] + [#] + [Telephone Number] + [#]

Delete Personal Telephone

Number

[▼for Phone] + [#] + [▼for Phone 1 - 4] + [#] + [0] + [#]

Installer Access Setting

[▼for Extra] + [#] + [▼for Ins Ac] + [#] + [Press 1 to toggle] + [#]

Phone Line Loss Detection Setting

[▼for Extra] + [#] + [▼for Ph Det] + [#] + [Press 1 to toggle] + [#]

PC Communication Setting

[▼for Extra] + [#] + [▼for PC Com] + [#] + [Press 1 to toggle] + [#]

4

T Sense Keypad Quick User & Installer Manual Rev 2.0

INSTALLER PROGRAMMING SHEET

Default Installer Pin 12345

Enter Installer programming mode: [INSTALLER CODE] +

[COM] + [#]

Symbol:

Exit Installer programming mode: Press and hold [*] for 2

seconds



Enable

Back to Installer programming main page: [*]



Disable

x

Unused

PC

Display

Item

Description

Zone Display (Default Setting)

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

Zone Type Setting

01

DELAY

Delay Zone

Zone number ON mean the zone

is assigned as Delay Zone





02

INSTAN

Instant Zone

Zone number ON mean the zone

is assigned as Instant Zone





03

INTER

Interior Zone

Zone number ON mean the zone

is assigned as Interior Zone



04

24 HR

24 Hour Zone

Zone number ON mean the zone

is assigned as 24 Hour Zone



05

LIGHT

Light Zone

Zone number ON mean the zone

is assigned as Light Zone



06

SILENT

Silent Zone

Zone number ON mean the zone

is assigned as silent Zone





Remark : Based on Zone Type Setting’s Table (Refer above table)

-Press the number to toggle the setting

Alarm Delay Setting



07

ENTRY1

Partition 1 Entry

Delay Timer

From 0 to 200 seconds

030#



08

ENTRY2

Partition 2 Entry

Delay Timer

From 0 to 200 seconds

000#



09

EXIT1

Partition 1 Exit

Delay Timer

From 0 to 200 seconds

060#



10

EXIT2

Partition 2 Exit

Delay Timer

From 0 to 200 seconds

000#



11

BELL

Bell Audible Time

From 1 to 30 minutes, 0 =

continuous

005#



Zone Partition

14

ZN

NUM

Individual Zone

Partition

Key in zone number

(01 - 16 #)



Part

Partition

Set 1 for partition 1. 2 for

partition 2.

1#

Zone Sensitivity Setting

16

ZN

NUM

Individual Zone

Sensitivity

Key in zone number

(01 - 16 #)



ZN SEN

Sensitivity level

From 1 to 100.

Sensitivity level x 10ms.

006#

17

P GRP

Zone Pulse Count

Group

Zone number ON mean the zone

is programmed to the zone pulse

count group



18

P CTR

Zone Pulse

Counter

From 1 to 255 times. If counter

exceed, zone pulse count group

will trigger

002#

19

P TMR

Zone Pulse

Counter Reset

Timer

From 1 to 255 seconds. Zone

pulse counter reset timer

090#



5

T Sense Keypad Quick User & Installer Manual Rev 2.0

Reporting Setting

30

TEL CT

Telephony

Control

Zone 1 ON mean enable DTMF

Dialling ELSE Pulse Dialling





x

Zone 2 ON mean enable Double

Call

31

RCV TY

Receiver Type

Zone 1 ON mean Receiver 1 is

Personal Reporting else CMS

reporting



x

Zone 2 ON mean Receiver 2 is

Personal Reporting else CMS

reporting



Zone 3 ON mean Receiver 3 is

Personal Reporting else CMS

reporting



Zone 4 ON mean Receiver 4 is

Personal Reporting else CMS

reporting



32

RCV OP

Receiver Options

Zone 1 ON mean Receiver 1 is

Permanent else Backup





x

Zone 2 ON mean Receiver 2 is

Permanent else Backup



Zone 3 ON mean Receiver 3 is

Permanent else Backup



Zone 4 ON mean Receiver 4 is

Permanent else Backup

33

REPORT

System Status

Report

Zone 1 ON mean enable Keypad

Alarm Reporting





x

Zone 2 ON mean enable System

Status (Combination of function

below)



A: System Status

B: Open Report

C: Close Report

D: System Reset Report

E: CMS Periodic Report

(*Proceed to 39 to set CMS

Periodic Test)

G: Alarm Restore Reporting

H: Bypass & Bypass Restore

Reporting

34

ZN RPT

Zone Alarm

Reporting

Zone number ON mean enable

Alarm Reporting



Remark : Based on Reporting Setting’s Table (Refer above table)- Press the number to toggle the setting

Communication Options



35

ACC 1

CMS Account

Number 1

4 digit CMS account number 1

0000#



36

ACC 2

CMS Account

Number 2

4 digit CMS account number 2

0000#



37

ACC 3

CMS Account

Number 3

4 digit CMS account number 3

0000#



38

ACC 4

CMS Account

Number 4

4 digit CMS account number 4

0000#



39

PERIOD

CMS Periodic Test

Report

From 0 to 24 hours

000#



40

RING

Ring Number

From 1 to 99 rings

010#



41

DL ATP

Dial Attempts

From 0 to 15 times

005#



42

DELAY

Delay Before Dial

Timer

From 0 to 150

000#



43

REDIAL

Redial Timer

From 0 to 10

000#

6

T Sense Keypad Quick User & Installer Manual Rev 2.0

Remark : Based on Communication Option’s Table (Refer previous table, page 6)

- Enter [0000] # to delete/clear CMS account number

Or

-Press [31] to enter command and press [1] # to set receiver type as personal type to disable CMS account number

Zone Circuit Type Setting

50

EOL

End of Line

Zone number ON means the zone

is EOL type else NO/NC type



51

NO NC

Normally

Open/Normally

Close

Zone number ON means the zone

is NO type else NC.



Remark : Based on Zone Circuit Type Setting’s Table (Refer above table)

- Press the number to toggle the setting

Keyswitch and Tamper Setting

52

KEYSET

Keyswitch setting

Zone 1 ON mean enable

keyswitch







X

Zone 2 ON mean the keyswitch is

Momentary else Latch Remote

Control

Zone 3 ON mean keyswitch is NC

type else NO type

Zone 4 ON mean enable

keyswitch Siren toot else Strobe

Light blink

(Toot once/Blink 3 sec: ARM;

Toot twice/Blink 8 sec: DISARM)

53

TAMPER

Tamper Setting

Zone 1 ON mean enable Tamper





X

Zone 2 ON mean Tamper

activated 24 hours else activate

during Arm

Zone 3 ON mean Tamper is NC

type else NO

Remark : Keyswitch and Tamper Setting’sTable (Refer above table)

- Press the number to toggle the setting

Programmable Output Setting

54

OC1

OC1 setting

Zone 1 ON mean enable OC1



X

Zone 2 ON mean enable OC1

with latch high output



X

Zone 3 ON mean enable OC1

with latch low output



X

Zone 4 ON mean enable OC1

with momentary high output



X

Zone 5 ON mean enable OC1

with momentary low output



X

Zone 6 ON mean OC1 activated in

alarm mode else arm & disarm

mode



X

(Zone 2 to zone 5 will toggle)



X

55

OC2

OC2 setting

Zone 1 ON mean enable OC2



X

Zone 2 ON mean enable OC2

with latch high output



X

Zone 3 ON mean enable OC2

with latch low output



X

Zone 4 ON mean enable OC2

with momentary high output



X

Zone 5 ON mean enable OC2

with momentary low output



X

Zone 6 ON mean OC2 activated in

alarm mode else arm & disarm

mode



X

(Zone 2 to zone 5 will toggle)



X

7

T Sense Keypad Quick User & Installer Manual Rev 2.0

56

OC3

OC3 setting

Zone 1 ON mean enable OC3



X

Zone 2 ON mean enable OC3

with latch high output



X

Zone 3 ON mean enable OC3

with latch low output



X

Zone 4 ON mean enable OC3

with momentary high output



X

Zone 5 ON mean enable OC3

with momentary low output



X

Zone 6 ON mean OC3 activated in

alarm mode else arm & disarm

mode



X

(Zone 2 to zone 5 will toggle)



X

57

OC4

OC4 setting

Zone 1 ON mean enable OC4



X

Zone 2 ON mean enable OC4

with latch high output



X

Zone 3 ON mean enable OC4

with latch low output



X

Zone 4 ON mean enable OC4

with momentary high output



X

Zone 5 ON mean enable OC4

with momentary low output



X

Zone 6 ON mean OC4 activated in

alarm mode else arm & disarm

mode



X

(Zone 2 to zone 5 will toggle)



X

Home Automation Setting

64

ET ZN1

Event Trigger

Zone Group 1

Zone LED ON mean the zone is

will turn on Event Trigger Output

when violated



65

ET IO1

Event Trigger

Output Group 1

Zone LED ON mean enable IO

point



66

ET ZN2

Event Trigger

Zone Group 2

Zone LED ON mean the zone is

will turn on Event Trigger Output

when violated



67

ET IO2

Event Trigger

Output Group 2

Zone LED ON mean enable IO

point



Remark : Home Automation Setting’s (Refer above table)

- Press the corresponding number to select the output to be activated (Toggle based)



System Security

70

LOCK C

Keypad Lock

Counter

From 1 to 255 times of password

error before keypad lock

010#

71

LOCK T

Keypad Lock Time

From 0 to 255 minutes

003#

72

INS CD

Change installer

code

5 digits installer code

12345#

8

DAIKIN ELECTRONIC DEVICES MALAYSIA SDN BHD

Daikin T Sense AX1 Instruction Manual

Popular Security System manuals by other brands