Dake SE-10 DM User manual

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
Phone: [phone]
Fax: [phone]
www.dakecorp.com
[email protected]
DAKE SEMI-AUTO DUAL MITERING BANDSAW
SE-10 DM
INSTRUCTIONAL MANUAL
WARNING!
Read and understand all instructions and responsibilities before operating. Failure to follow
safety instructions and labels could result in serious injury.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 1 REV112019
TABLE OF CONTENTS
DAKE STANDARD LIMITED WARRANTY............................................................ 2
RETURN & REFUND POLICY..............................................................................4
SPECIFICATIONS ................................................................................................5
SAFETY WARNINGS............................................................................................ 6
MAIN MACHINE CONTROLS............................................................................... 9
SET UP............................................................................................................... 10
TRANSPORTATION OF MACHINE........................................................... 10
ADJUSTMENTS.................................................................................................. 11
TOOTH SELECTION ................................................................................. 11
BLADE SPEED.......................................................................................... 12
OPERATIONS..................................................................................................... 13
STARTING SAW........................................................................................ 13
USAGE OF THE QUICK RELEASE & TRAVERSING VISE....................... 13
QUICK HEAD ADJUSTMENT FOR ANGLE CUTS.................................... 14
CUTTING SPEED ADJUSTMENT ............................................................. 15
DOWN FEED CONTROLS ........................................................................ 15
HEAD FRAME BALANCE ADJUSTMENT ................................................. 16
MAINTENANCE.................................................................................................. 17
CHANGING BLADE................................................................................... 17
TROUBLESHOOTING........................................................................................ 18
ELECTRICAL DIAGRAM .................................................................................... 20
EXPLODED VIEWS & PART LIST...................................................................... 21
ORDERING INFORMATION............................................................................... 22

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 2 REV112019
DAKE STANDARD LIMITED WARRANTY
Finished Machines
Dake warrants to the original purchaser the finished machine manufactured or distributed by it to be free
from defects in material and workmanship under normal use and service within 1 year (12 months) from
the delivery date to the end user.
Parts
Dake warrants to the original purchaser the component part manufactured or distributed by it to be free
from defects in material and workmanship under normal use and service within 30 days from the delivery
date to the end user.
The standard limited warranty includes the replacement of the defective component part at no cost to the
end user.
Sale of Service (Repairs)
Dake warrants to the original purchaser the component part repaired by Dake Corporation at the
manufacturing facility to be free from defects in material and workmanship under normal use and service
within 90 days from the return date to the end user, as it pertains to the repair work completed. The
standard limited warranty includes repair of the defective component part, at no cost to the end user.
Warranty Process
Subject to the conditions hereinafter set forth, the manufacturer will repair or replace any portion of the
product that proves defective in materials or workmanship. The manufacturer retains the sole right and
option, after inspection, to determine whether to repair or replace defective equipment, parts or
components. The manufacturer will assume ownership of any defective parts replaced under this
warranty.
All requested warranty claims must be communicated to the distributor or representative responsible for
the sale. Once communication has been initiated, Dake Customer Service must be contacted for
approval:
Phone: [phone]
Email: [e-mail]
When contacting Dake, please have the following information readily available:
- Model #
- Serial #
- Sales Order #
Purchasers who notify Dake within the warranty period will be issued a Case number and/or a Return
Material Authorization (RMA) number. If the item is to be returned per Dake’s request, the RMA number
must be clearly written on the exterior packaging. Any item shipped to Dake without an RMA will not be
processed.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 3 REV112019
Warranty Exceptions:
The following conditions are not applicable to the standard limited warranty:
(a) Part installation or machine service was not completed by a certified professional, and is not
in accordance with applicable local codes, ordinances and good trade practices.
(b) Defects or malfunctions resulting from improper installation or failure to operate or maintain
the unit in accordance with the printed instructions provided.
(c) Defects or malfunctions resulting from abuse, accident, neglect or damage outside of prepaid
freight terms.
(d) Normal maintenance service or preventative maintenance, and the parts used in connection
with such service.
(e) Units and parts which have been altered or repaired, other than by the manufacturer or as
specifically authorized by the manufacturer.
(f) Alterations made to the machine that were not previously approved by the manufacturer, or
that are used for purposes other than the original design of the machine.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 4 REV112019
RETURN & REFUND POLICY
Thank you for purchasing from Dake! If you are not entirely satisfied with your purchase, we are
here to help.
Returns
All Dake manufactured / distributed machines, parts and couplings include a 30-day return
option. These policies are valid from the date of final shipment to the end user.
To be eligible for a return, the item must be unused and in the same condition as received.
All requested warranty claims must be communicated to the distributor or representative
responsible for the sale. Once communication has been initiated, Dake Customer Service must
be contacted for approval:
Phone: [phone]
Email: [email protected]
Once the return request has been approved by Customer Service, a representative will supply a
Return Material Authorization (RMA) number. The returned item must have the provided RMA
number clearly marked on the outside packaging. Any item received without an RMA number
clearly visible on the packaging will not be processed.
An RMA number can only be provided by the Dake Customer Service team and must be
obtained prior to the return shipment.
Refunds
Once the item has been received and inspected for damages, a representative will notify the
requestor referencing the provided RMA number.
If the return is approved, a refund will be issued to the original method of payment, less a 20%
restocking fee. The restocking fee may be waived if an order is placed at the time of return with
like-value merchandise.
Transportation costs are the responsibility of the end user and will not be credited upon return
approval.
Any item that is returned after the initial 30 days or has excessive/obvious use will not be
considered for a full refund.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 5 REV112019
SPECIFICATIONS
Machine Type
Hydraulic controlled feed
horizontal mitering band
saw
Weight
770 lbs.
Blade Size
108” x 1”
Work Height
37”
Blade Speeds
115/230 FPM
Overall Height,
Open / Closed
74” open / 62” closed
Head Feed
Hydraulic controlled down
feed with
Base Width
28”
Vise
Manual with quick release
Depth
66”
Miter Cutting
Capabilities
Up to 60° right / 45° left
Lubricant
Flood type unit built into the
machine (electric)
Controls
CE Certified
Voltage
Available 220-volt three
phase
Horsepower
2.75
AMP
20-amp service for 230-volt
machine
CUTTING CAPACITIES
Degree
Round
Square
Flat
90°
10”
7-1/2”
12-1/2” x 7-3/4”
60°
5”
5”
4-3/4” x 5-1/4”
45° R/ L
8” / 8”
7-1/2” / 6-3/4”
8-14” x 3-1/8” /
6-1/2” x 7-3/8”
In the space provided record the serial number and model number of the machine. This
information is only found on the black Dake tag. If contacting Dake this information must be
provided to assist in identifying the specific machine.
Model No:
SE-10 DM
Part No:
983112
Serial No:
Date of Purchase:

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 6 REV112019
SAFETY WARNINGS
WARNING: FAILURE TO FAOLLOW THESE RULES
MAY RESULT IN SERIOUS PERSONAL INJURY
As will all machinery there are certain hazards involved with operation and use of the machine.
Using the machine with respect and caution will considerably lessen the possibility or personal
injury. However, if normal safety precautions are overlooked or ignored, personal injury to the
operator may result.
This machine was designed for certain applications only. We strongly recommend that this
machine NOT be modified and/or used for any application other than for which it was designed.
If you have any questions relative to its application DO NOT use the machine until you contact
with us and we have advised, you.
Your machine might not come with a power socket or plug. Before using this machine,
please ask your local electrician to install the socket or plug on the power cable end.
SAFETY RULES FOR ALL TOOLS
USER:
•Wear proper apparel: No loose clothing, gloves, rings, bracelets, or other jewelry to get
caught in moving parts. Non-slip foot wear is recommended. Wear protective hair
covering to contain long hair.
•Always wear eye protection. Refer to ANSLZ87.1 standard for appropriate
recommendations. Also use face or dust mask if cutting operation is dusty.
•Do not overreach. Keep proper footing and balance at all times.
•Never stand on the machine. Serious injury could occur if the machine is tipped or if the
cutting blade is accidentally contacted.
•Never leave the saw running unattended. Turn off power. Don't leave saw until it comes
to a complete stop.
•Do not operate the tool while under the influence of drugs, alcohol, or any medication.
•Make sure the saw is disconnected from power supply while motor is being mounted,
connected, or reconnected.
•Always keep hands and fingers away from table.
•Stop the machine before removing any chips or debris.
•Shut off power and clean the band saw and work area before leaving machine.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 7 REV112019
USE OF MACHINE:
•Remove adjusting keys and wrenches. Form a habit of checking to see that keys and
adjusting wrenches are removed from the saw before turning it on.
•Do not force the saw. It will do a more efficient and safer job at the rate for which it was
designed.
•Use correct blade. Do not force blade or attachments to do a job for which it was not
designed.
•Secure work. Use clamps or a vise to hold work when practical. It is safer than using your
hands.
•Maintain blade is in top condition. Keep blades sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
•Use recommended accessories. Consult the owner’s manual for recommended
accessories. The use of improper accessories may cause hazards.
•Avoid accidental starting. Make sure the switch is in the “OFF” position before plugging in
the cord.
•Direction of feed. Feed work into the blade against the direction of rotation of the blade.
•Adjust and position the blade guide arm before starting the cut.
•Keep blade guide arm tight. A loose blade guide arm will affect sawing accuracy.
•Make sure blade speed is set correctly for material being cut.
•Check for proper blade size and type.
•Stop the machine before putting material in the vise.
•Always have stock firmly clamped in vise before starting the cut.
•Ground all tools. If tool is equipped with three-prong plug, it should be plugged into a
three-hole electrical receptacle, the adapter plug must be attached to a known ground.
Never remove the third prong.
ADJUSTMENTS:
•Make all adjustments with the power off. In order to maintain the machine, precision and
correct ways of adjustment while assembling, the user should read the detailed
instruction in this manual.
WORKING ENVIRONMENT:
•Keep work area clean. Cluttered areas and benches invite accidents.
•Do not use in dangerous environment. Do not use power tools in damp or wet locations
or expose them to rain. Keep work area well-lighted.
•Keep children and visitors away. All children and visitors should be kept a safe distance
from work area.
•Do not install or use this machine in an explosive, dangerous environment.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 8 REV112019
MAINTENACNE:
•Disconnect machine from power source when making repairs.
•Check damaged parts. Before further use of the saw, a guard or other part that is
damaged should be carefully checked to ensure that it will operate properly and perform
its intended function check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condition that may affect its operation. A
guard or other part that is damaged should be properly repaired or replaced.
•Disconnect tools before servicing and when changing accessories such as blades, bits,
cutters, etc.
•Make sure that the blade tension is properly adjusted. The gauge when properly
tensioned will show the needle in the “green” zone.
•Re-check blade tension after initial cut with new blade.
•To prolong blade life always releases blade tension at the end of each work day.
•Check coolant daily. Low coolant level can cause foaming and high blade temperatures.
Dirty or weak coolant can clog pump. This can cause low cutting rate and permanent
blade failure. Dirty coolant can cause the growth of bacteria with ensuring skin irritation.
•When cutting magnesium never use soluble oils or emulsions (oil-water mix) as water will
greatly intensify any accidental magnesium chip fire. See your industrial coolant supplier
for specific coolant recommendations when cutting magnesium.
•To prevent corrosion of machined surfaces when a soluble on is used as coolant, pay
particular attention to wiping dry the surfaces where fluid accumulates and does not
evaporate quickly, such as between the machine bed and vise.
SPECIFIC USAGE:
This machine is used for general metals cutting within the range of cutting capacity.
SAFETY DEVICE:
By the time the saw arm cover is opened, the interlock switch will function to stop the all
involvement. Do not remove this switch from machine for any reason and check its function
frequency.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 9 REV112019
MAIN MACHINE CONTROLS

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 10 REV112019
SET UP
TRANSPORTATION OF MACHINE
This machine weighs 770lbs.
Transport to desired location before unpacking, please use lifting jack.
Transportation after unpacking, please use heavy duty fiber belt to lift up the machine.
Always keep proper footing and balance while moving this machine.
Minimum space required for machine operation below:
INSTALLATION:
Assemble saw pedestal and bolt saw on the pedestal.
1. Tighten all locks before operation.
2. Turn off the power before wiring, and be sure machine is properly grounded. Overload
and circuit breakers are recommended for safety wiring.
3. Check carefully if the saw blade is running in counterclockwise direction, if not, reverse
the wiring per circuit diagram then repeat running test.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 11 REV112019
ADJUSTMENTS
TOOTH SELECTION
For maximum cutting efficiency and lowest cost per cut, it is important to select the blade with
the right number of teeth per inch for the material being cut. The material size and shape dictate
tooth selection.
You need to consider:
The width of the cut. That is, the distance in the cut that each tooth must travel from the point it
enters the work piece until it leaves the work piece, and the shape of the work piece. Use the
chart above to assist with tooth selection.
•Squares, Rectangles, Flats (Symbol: ■)
Locate the width of your work piece on the chart. (Inches on the outer circle and
millimeters on the inner circle.) Select the tooth pitch on the ring marked with square
which aligns with the width of the cut.
Example: 6” (150mm) square, use a 2/3 Vari-Tooth.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 12 REV112019
•Round Solids (Symbol: ●)
Locate the diameter of your work piece on the chart. Select the tooth pitch on the ring
marked with the circle which aligns with the size of stock you are cutting.
Example: 4” (100mm) round, use a 3/4 Vari-Tooth.
•Tubing, Pipe, Structural (Symbols: O, H, ˄)
Determine the average width of cut by dividing the area of the work piece by the distance
the saw blade must travel to finish the cut. Select the tooth pitch on the ring marked with
the tubing and structural shape which aligns with the average width you are cutting.
Example: 4”(100mm) outside diameter, 3” (75mm) inside diameter tubing.
4"(100mm) OD =12.5 in2(79 cm2)
3"(75 mm ) ID = 7.0 in2(44 cm2)
Area = 5.5 in2(35 cm2)
5.5 in2(35 cm2) / 4" (100mm) distance = 1.38”(35 mm) average width 1.38" (35 mm),
use a 4/6 Vari-Tooth.
BLADE SPEED
The band speeds are to be used as a starting point for most application. For exact parameters
consult your saw blade supplier.
Material
Speed (FPM)
Tool, Stainless, Alloy Steels, Bearing Bronze
114
Med. to High Carbon Steels, Hard Brass or Bronze
114
Low to Med. Carbon Steel, Soft Brass
230
Aluminum, Plastic
230
TELLTALE CHIPS
Chips are the best indicator of correct feed force. Monitor chip information and adjust feed
accordingly.
Thin or powdery chips –increase feed rate or reduce band speed.
Burned heavy chips –reduce feed rate and/or band speed.
Curly silvery and warm chips –optimum fed rate and band speed.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 13 REV112019
OPERATIONS
STARTING SAW
Trigger switch located on control handgrip of the saw used for starting the blade in manual or
semi-automatic mode.
CAUTION: NEVER OPERATE SAW WITHOUT BLADE GUARDS IN PLACE.
Be sure the blade is not in contact with the work when the motor is started. Start the motor,
allow the saw to come to full speed, then begin to cut by letting the head down slowly onto the
work. DO NOT DROP OR FORCE. Let the weight of the saw head produce the cutting force.
The saw automatically shuts off at the end of the cut.
USAGE OF THE QUICK RELEASE & TRAVERSING VISE
The workpiece is places between the vise jaws with the amount to be cut off extending out past
the blade. Your machine is equipped a handwheel and quick release lever that moves the
clamping jaw forward and backwards. With material in place run the vise jaw up to where it just
touches the material, then back off the jaw a quarter turn or enough so the material, can slightly
move. (Make sure when you adjust the vise that the quick release lever is in the up position).
Now push the lever down to lock the material for cutting. Pull up on the lever to release the
material.
The vise can also be positioned left or right of the blade, so you can miter cut in both directions.
This is accomplished by pulling the traversing lever to unlock the vise then you can slide the
vise left or right. Lock vise down with the lever.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 14 REV112019
QUICK HEAD ADJUSTMENT FOR ANGLE CUTS
1. Loosen head swivel lock handle.
2. Rotate head to the required angle by aligning the indicator to the scale. Three presets
can be used or any angle in between.
3. Lock head back down.
For mitering left or right flip up the stop located on the left side attached to the base or the
stop pin on the right side of the base.
m
Head
swivel lock

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 15 REV112019
CUTTING SPEED ADJUSTMENT
CAUTION - Always allow blade to achieve speed before starting your cut and never
change speeds while cutting.
DOWN FEED CONTROLS
Head feed speed control:
These controls regulate the speed at which the head descends and the pressure. The head feed
rate control speeds up when turned counter-clockwise and slows down when rotated clockwise.
Head lock control:
Rotating this knob allows the head to descend down to the material. Always stop before coming
in contact with the material. Open this knob when you are ready to start the head feed down for
your cut. This control can be closed at any time to stop the head without going all the way up or
down.
Mode Switch:
Allows cutting either in the manual or semi-automatic mode. When cutting in manual mode
adjust your cut rate with the “head feed speed control”. That will control the maximum down feed
rate you can use while keeping the trigger pulled. For semi-auto hands free cutting adjust your
head height speed and feed. Pull the trigger and release. The saw will stop at the end of the cut.
Speed selector switch located on thee control box
and has two blade speeds 1 & 2.
1 = 115 FPM
2 = 230 FPM
Select 1 or 2 and activate the trigger switch on
the handle to begin your cutting operation.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 16 REV112019
HEAD FRAME BALANCE ADJUSTMENT
Manual Cutting:
With the mode selector switch set to manual cutting selection the counterbalance weight should
be set as shown below. At this tension the counterbalance springs allowing for greater control
when manual cutting and returning the head to the rest position.
Automatic Cutting:
When cutting in automatic mode selector switch must be in the auto selection. The spring
tension must be released as shown below, this gives the appropriate head weight for
unattended cutting.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 17 REV112019
MAINTENANCE
CAUTION - WARNING
Make certain that the unit is disconnected from the power source before attempting to
service or remove any component.
It is easier to keep the machine in good condition or best performance by means of maintaining
it at any time than remedy it after it is out of order.
Regular Maintenance Schedule:
Daily
Check and fill cutting fluid if needed, before starting the machine every day.
Water soluble cutting fluid is recommended. Avoid cutting oils.
If there is a strange or unusual noise or malfunction, stop the machine
immediately to check it for the problem source. Repairs must be made by
qualified personnel before continuing use.
Clean work area.
Weekly
Clean and coat any machines surfaces with oil to prevent rust.
Check to see if sliding surfaces and turning parts lack of lubricant. If
lubrication is insufficient, fill it.
Monthly
Check electrical cord, plugs, switched at least once a month to avoid
loosening or wearing.
CHANGING BLADE
Check the compatibility of the NEW blade for the saw. Only use a blade with a thickness
between .025” and .035”.
Raise saw head to upper most position and open the blade guards. Loosen tension screw knob
sufficiently to allow the saw blade to slip off the wheels. Install the new blade with the teeth
slanted toward the motor as follow:
1. Place the blade in between each of the guide bearings.
2. Slip the blade around the motor wheel (rear) with the left hand and hold on position.
3. Hold the blade taut against the motor wheel by pulling the blade towards the front wheel
with the right hand and adjust the position of the front wheel by slipping the blade around
the wheel using thumb, index, and little finger as guides.
4. Adjust the blade tension handwheel clockwise until the needle is in the green zone of the
gauge face. Do not tighten excessively.
5. Replace the blade guards. Rear blade cover has interlocks and will not allow the saw to
run without these interlocks engaged.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 18 REV112019
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Excessive Blade
Breakage
1. Materials loosen in vise.
1. Clamp work securely.
2. Incorrect speed or feed.
2. Adjust speed or feed.
3. Blade teeth spacing too
large.
3. Replace with a finer tooth
spacing blade.
4. Material too coarse for
blade.
4. Use a blade at slower speed
with proper teeth spacing.
5. Incorrect blade tension.
5. Adjust to where the green LED
lights up.
6. Teeth in contact with
material before saw is
started.
6. Place blade in contact with
work after motor is started.
7. Blade runs on wheel flange.
7. Adjust wheel alignment.
8. Miss-aligned guide bearings.
8. Adjust guide bearings.
9. Blade is too thick.
9. Use a thinner grade.
10. Cracking at weld.
10. Reweld blade.
Premature Blade
Dulling
1. Teeth too coarse.
1. Use finer teeth.
2. Blade speeds too fast.
2. Reduce speed.
3. Inadequate feed pressure.
3. Adjust pressure setting.
4. Hard spots or scale on
material.
4. Reduce speed, increase feed
pressure.
5. Work hardening of material.
5. Increase feed pressure.
6. Blade twist.
6. Replace with a new blade and
adjust blade tension.
7. Insufficient blade tension.
7. Tighten blade tension
adjustment knob.
8. Blade slips.
8. Tighten blade tension.
Unusual Wear on
Side/Back of Blade.
1. Blade guides worn.
1. Replace.
2. Blade guides not adjusted
properly.
2. Adjust.
3. Blade guides are loose.
3. Tighten.
Teeth Ripping from
Blade
1. Tooth too coarse for work.
1. Use finer tooth blade.
2. Too heavy of pressure; too
slow of speed.
2. Decrease pressure, increase
speed.
3. Vibrating workpiece.
3. Clamp workpiece securely.
4. Gullets loading up.
4. Use coarser tooth blade or
brush to remove chips.

Dake Corporation
724 Robbins Road
Grand Haven, MI 49417
www.dakecorp.com
983112-2 19 REV112019
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Bad Cuts (Crooked)
1. Feed pressure too great.
1. Reduce pressure.
2. Guides not adjusted
properly. Too far from work.
2. Adjust guides closer to work.
3. Inadequate blade tension.
3. Increase blade tension.
4. Dull blade.
4. Replace blade.
5. Blade speed is incorrect.
5. Adjust speed.
6. Blade guide assembly loose.
6. Tighten.
7. Blade tracking too far away
from wheels.
7. Re-track blade.
Bade Cuts (Rough)
1. Too much speed or feed.
1. Decrease speed or feed.
2. Blade is too coarse.
2. Replace with finer blade.
3. Blade tension loose.
3. Adjust blade tension.
Blade is twisting.
1. Cut is binding blade.
1. Decrease feed pressure
2. Too much blade tension
2. Decrease blade tension.