Dakota Digital LED Tail Lights for 1969 Camaro LAT-NR111 User manual

MAN#650170
INSTALLATION INSTRUCTIONS
LAT-NR111
LED Tail Lights for 1969 Camaro
MAN#650170
Kit Includes:
Installation:
1. Remove the original bulb connectors from the bottom side of the housing.
2. Remove the plastic housing from the vehicle.
3. Remove the tail light lens by gently prying the housing away from the lens tabs.
4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is
recommended.
5. Note that the screws and mounting plates are assembled differently for the driver side set and
passenger side set. The LED assemblies will sit in the housing at an angle similar to the back
side of the original lens.
driver side(screws and mounting plate offset to the left)
passenger side(screws and mounting plate offset to the right)

MAN#650170
6. Insert each new LED assembly through the hole where the original bulb and connector were
located. Use caution when feeding the wires through the socket opening to avoid damaging
the wire insulation.
7. Feed the wires through the large hole in the back plate and attach the
back plate onto the back side of the housing. The flat side of the
mounting plate should be toward the outside and the side with the
slight raised center should go in towards the housing. This will align
the mount in the original housing.
8. Secure the LED assembly into the housing with the supplied back plate and #6 lock nuts.
9. Place the original lens gasket into place and replace the tail light lens.
10.Cut off the existing light socket as it will not be used. Do not strip the wires. Trim the wires
from LED assembly to appropriate length once mounted, making sure wires are routed cleanly
and securely.
11.Use the supplied moisture resistant pigtail connectors* to attach the wires from the new LED
assembly to the existing vehicle harness. Insert the appropriate wire from vehicle harness and
mating LED assembly wire into a connector and crimp following instructions below.
*For the best connection, soldering is recommended. But to simplify installation, the supplied connectors will
provide a fast weather resistant connection.
The correct crimp method for the supplied connectors is:
1.) Insert UNSTRIPPED wires into the connector and ensure they are all they way in by
observing the clear bottom of the connector to see the wires are touching the end.
2.) Use pliers to push the blue cap down flush with the edge of the clear body, completing the
connection. The connection will only be correct if pressed firmly down with pliers.

MAN#650170
LED light
Vehicle harness
Tail light
Brown
Brown
Driver’s Turn
Green
Green
Passenger’s Turn
Green
Yellow
Ground
Black
Black or chassis
12.Repeat for the other side.
13.Test the tail lights, brake lights, and turn signals. If the turn signals do not flash you will need
to upgrade your flasher. If you are replacing only the rear turn signals you should be able to
use a heavy duty electronic flasher from your local parts store. If you are replacing both front
and rear or do not have front bulbs you will need a no-load flasher, Dakota Digital part number
LAT-NLF.
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is available to help you work through any questions or
problems you may be having installing one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to most problems.
Should you ever need to send the unit back for repairs, please call our technical support line, [phone], to request a Return Merchandise Authorization
number.Package the product in a good quality box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure to include the RMA
number on the package, and include a complete description of the problem with RMA number, your full name and address (street address preferred), and a telephone number
where you can be reached during the day. Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase. Send no money. We will
bill you after repair.
Dakota Digital Limited Lifetime Warranty
DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under normal use and condition, be proven defective in material or
workmanship for the lifetime of the original vehicle it was installed in, such defect(s) will be repaired or replaced at Dakota Digital’s option.
This warranty does not cover nor extend to damage to the vehicle’s systems, and does not cover removal or reinstallation of the product. This Warranty does not
apply to any product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling, misuse, neglect, or
accident. This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties, including any implied warranty of merchantability, shall be limited to
the duration of this written warranty. No person or representative is authorized to assume, for Dakota Digital, any liability other than expressed herein in connection with the
sale of this product.
4510 W. 61ST St. N., Sioux Falls, SD 57107
Phone: [phone] FAX: [phone]
www.dakotadigital.com
[e-mail]
©Copyright 2008 Dakota Digital Inc.