Dakota Digital BIM-05-1 User manual

MAN #650343b
BIM-05-1
Bus Interface Module for voltage and current
(Current sensors are sold separately)
0-5 V
0-50 V
0-5 V
0-50 V
Connect to main
chassis ground
+12V KEY ON POWER
(fused 5 - 20 AMP max)
setup/status switch
To gauge control box
or another BIM
SEN-20-3
Ground
Power
Output
www.dakotadigital.com
605-332-6513
Device monitored by Channel 2
Device monitored by Channel 1
+12V KEY ON POWER
(fused 5 - 20 AMP max)
Connect to BIM-05
GND terminal Connect to BIM-05 V LO input
Optional
SEN-20-3
for current
monitoring
(purchased separately)
* Connect VHI or VLO, but not both.
To load to be monitored
V LO #1 V HI #1
BIM-05-1
VOLT / CURRENT
V HI #2 V L0 #2
PWR
GND
www.dakotadigital.com
[e-mail]
605-332-6513
I/O I/O
This Bus Interface Module has inputs for up to two devices to be monitored. Each channel can be configured
individually. There are two interface (I/O) ports on the module. Either one can be connected to the gauge system or to
another module, allowing several units to be daisy chained together. Do not connect the I/O port to anything other
than a Dakota Digital gauge or BIM. Do not mount the module in the engine compartment; it should be mounted in
interior of the vehicle.
Each sensor connected to the bus needs a unique ID number assigned to it. This module has inputs for two channels
so it can use one or two ID numbers. Each of the two channels can be assigned an ID from 1 – 16, or turned off. The
factory default ID numbers are 3 and 4 for the two inputs respectively. The factory default labels are VOLTS for both.
Labels available for each input are:
VOLT - voltage input. This will display VOLT, V, or BIM VOLTAGE.
CURRENT - SEN-20-3 sensor input. This will display AMPS, C, or CURRENT.
Specs for each input are:
Part # Input Range resolution low warning high warning
VOLT none V HI 0 – 50.0 V 0.1 0 – 31 10 – 41
VOLT none V LO 0 – 5.00 V 0.01 0 – 3.1 1.9 – 5.0
CURRENT SEN-20-3 V LO 0 – 250 A 1 none 5 – 320

MAN #650343b
To set or change the ID numbers:
•Hold the switch beside the BIM terminal strip while turning the key on. The BIM display will show the current
revision code while this is held.
•Release the switch. The display will show ì-C-”.
•Press the switch. The BIM display will show “C-1”.
•Release the switch. The display will show the current ID for channel 1.
•Press and release the switch to change the setting from 1-16 or OFF.
•Press and hold the switch to save the setting. The BIM display will show “C-2”.
•Release the switch. The display will show the current ID for channel 2.
•Press and release the switch to change the setting from 1-16 or OFF.
•Press and hold the switch to save the setting. The BIM will restart with the new settings.
The labels and warning points are set up through the gauge display system.
Only VFD3/3X controls with a plastic case support adding BIM’s.
For VFD3, VFD3X, and VHX systems follow these steps:
•If the V HI input is being used, make sure it has voltage applied to it during setup. The BIM unit auto-detects
whether the V HI or V LO is being used by measuring the voltage on each. If both are off it will default to V
LO.
•Make sure the BIM units are all connected to the gauge control box with the 3.5mm data cables.
•Hold the SW1 switch from the gauge system control box while turning the key on. The message display
should show SETUP.
•Release SW1.
•Press and release SW1 until BIM is shown on the message display.
•Press and hold SW1. The message display should show SCAN followed by the number of BIM channels
detected. Release SW1.
•If 0 is shown, check all connections and then press and hold SW1 with SCAN shown to retry reading the
modules.
•Otherwise, if any other number is shown, press and release SW1 until SETUP is shown.
•Press and hold SW1 until the speed display shows “ – ” or the message changes.
•Release SW1. On the VFD3 systems the message display will show the label assigned to the first channel
found and the speed display will show “C” followed by the channel ID number. On the VHX systems the
message display will show “CH” followed by the channel ID number on one line and the label currently
assigned on the second line.
•Press and release SW1 until the desired channel ID number is shown.
•Press and hold SW1. The message display will show “LABEL”.
•Release SW1. The message display will show the label assigned to this channel.
•Press and release SW1 until the desired label is shown.
•Press and hold SW1. The message display will show “WARN”.
•Release SW1. The message display will show “L” followed by the current low warning point or will flash the
warning point.
•Press and release SW1 to change the low warning point to the desired value.
•Press and hold SW1 until the speed display shows “ – ”.
•Release SW1. The message display will show “H” followed by the current high warning point or will flash the
warning point.
•Press and release SW1 to change the high warning point to the desired value.
•Press and hold SW1. The message display will now show “DONE”.
•This can be repeated for additional channels, or the key can be turned off to exit setup.

MAN #650343b
For HDX systems follow these steps:
•Make sure the BIM units are all connected to the gauge control box.
•With the ignition on, press and hold both switches to enter SETUP. With external switches hold either one
while turning the ignition on. Release the switches when SETUP is shown.
•Press and release either switch until BIM is selected. Press and hold either switch to enter BIM setup menu.
•Release the switch. A list of the BIM’s found should be shown. If NONE FOUND is displayed then check
connections to the BIM-05.
•Press and release either switch until BIM-05 is selected.
•Press and hold either switch to enter setup for this module.
•Release the switch. The menu will show FORMAT, LABEL, WARN LO, WARN HI, CALIBRATE, BACK. Any
menu that does not apply to this BIM will be grey and cannot be selected.
•Use either switch to select the option you wish to change, (refer to the HDX manual for specifics).
•When you are finished select BACK to return to the BIM selection menu.
•When you are finished, select BACK to return to the BIM list menu, select BACK to return to the main menu,
and then select EXIT SETUP to return to normal operation.
With HDX systems the setup can also be done with the Dakota Digital app for Apple and Android devices.
Troubleshooting quick tips:
While the BIM is operating, the dot in the upper left corner of the display will indicate the status. On steady indicates it
is powered up but not receiving any bus activity. Flashing indicates it is communicating on the bus.
To see the sensor and channel status on the BIM display, press and hold the switch. The display will cycle through
three screens. The first will show the sensor input status. Each digit on the display will show the status for one of the
channels. ‘E’ indicates there is a bus ID conflict on that channel ID. ‘-’ indicates the sender is connected properly. If
the input is turned off the digit will be blank.
The second screen will show the ID assigned to channel 1. The third screen will show the ID assigned to channel 2.
Troubleshooting guide.
Problem Possible cause Solution _
Sensor does not show on PWR terminal does not have power. Connect to a location that has power.
gauge readout. GND terminal does not have a good Connect to a different ground location.
BIM will not light up at all. ground.
Module is damaged. Return for service. (see instructions) _
Sensor does not show on Interface cable is not connected. Connect the supplied 3.5mm data cable between the BIM unit and
gauge readout. the gauge control box.
BIM has a steady dot lit Interface cable is loose. Make sure both ends of the cable are seated in securely.
On VHX systems, the BIM display Follow instructions in VHX manual to enable the BIM display screen.
for this channel is disabled.
Another BIM is set with the same Test module works when connected to control box alone. Change ID’s
channel IDs. on one of the modules so each module uses unique IDs. _
Gauge lights up, but does Loose connection on sensor wires. Inspect and reconnect wires.
not read correctly. Connector not seated on sensor. Reattach the sensor plug, making sure the locking tab clicks in place.
Channel sensor label setup is incorrect. See “Setting sender setup” in the manual.
Wrong input is being used. Use V HI for 0-50V and V LO for 0-5V.
Voltage or wiring problem in the Check wiring harness for loose or damaged wires.
vehicle wiring harness.
BIM display shows “88:8” Data cable is damaged. Inspect and replace 3.5mm data cable.
Another module on the bus is damaged Inspect other modules on the data bus.
or connected improperly.

MAN #650343b
SERVICE AND REPAIR
DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical
consultation is available to help you work through any questions or problems you may be having installing
one of our products. Please read through the Troubleshooting Guide. There, you will find the solution to
most problems.
Should you ever need to send the unit back for repairs, please call our technical support line, (605)
332-6513, to request a Return Merchandise Authorization number. Package the product in a good
quality box along with plenty of packing material. Ship the product by UPS or insured Parcel Post. Be sure
to include the RMA number on the package, and include a complete description of the problem with RMA
number, your full name and address (street address preferred), and a telephone number where you can be
reached during the day. Any returns for warranty work must include a copy of the dated sales receipt from
your place of purchase. Send no money. We will bill you after repair.
Dakota Digital Limited Lifetime Warranty
DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it, under
normal use and condition, be proven defective in material or workmanship for the lifetime of the original
vehicle it was installed in, such defect(s) will be repaired or replaced at Dakota Digital’s option.
This warranty does not cover nor extend to damage to the vehicle’s systems, and does not cover
diagnosis, removal or reinstallation of the product. This Warranty does not apply to any product or part
thereof which in the opinion of the Company has been damaged through alteration, improper installation,
mishandling, misuse, neglect, or accident. Dakota Digital assumes no responsibility for loss of time,
vehicle use, owner inconvenience nor related expenses.
Dakota Digital will cover the return standard freight once the product has been evaluated for warranty
consideration, however the incoming transportation is to be covered by the owner.
This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties,
including any implied warranty of merchantability, shall be limited to the duration of this written warranty. No
person or representative is authorized to assume, for Dakota Digital, any liability other than expressed
herein in connection with the sale of this product.
WARNING:
This product can expose you to chemicals including lead, which is known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P 5Warnings.ca.gov