Dancing Wings Hobby Night Devil User manual

Suggested Equipment
Motor: 2216 900-1100KV
ESC: 20A
Propeller: 9-10 inch
Servos: 9g*4
Battery: 3s 2200-2600mAh
Radio≥4CH
Speci�ication
Wingspan: 1000mm
Length: 820mm
Flying Weight≈730g
Accessories include
Power System（Optional）
Preparation Tool
A：wood sheets B1：steel wire pushrod
B2：cabon sheets C1：front landing gear
C2：middle landing gear D1-7：EPP sheets
E：screws,EZ-Connector,servo horn
F1：wireless remote switch (optional)
F2：JST extension wire G：wood sticks
H：propeller I：rubber band
How to Assemble
1.Paste the wood sheet A3 and A1 onto the D1 by foam
glue,pay attention to aim at the preserved holes and put
in the right direction.(paste the other side of D1 in same
way)
2.Take down the wood sheet A2,A4 and A5,and assem-
ble as picture shown.(Do not glue them now)
3.Paste together the finished D1 and components from
step 2,pay attention to the direction of wood sheets A4
and A2.Adjust and paste by glue 502.
Night Devil Instruction Manual EPP Airplane
B1
AA
B2
C1
C2 I
D1 D2
D3
D4
D5
D6
D7
E
F1
F2
G
H
A3
D1
A1
A5X2
A4
A2X2
fuselage head direction
pay attention to the gap direction
alignment hole

4.Assemble the motor and front landing gear onto the
A2 (as picture shown below),fix the motor with screws,-
fix the landing gear with screws and nuts,connect the
landing gear arm with steel wire pushrod,which insert
through the preserved hole on A4,and finally connect
with the servo.
6.Paste the D5 at the bottom of the fuselage by foam
glue,and pull the JST connector out of the wood sheets.
7.Assemble the landing gear as per the bottom preserved
hole,and fix with screws.
8.Assemble the tail reinforcement,and paste with glue
502.
9.Paste the tail reinforcement at the tail of the fuselage
by foam glue,and pull the JST connector out of the hole.
5.Paste the A6 onto the A5 by glue 502,and assemble the
nuts in the preserved holes on the back side of the A5.
Night Devil Instruction Manual EPP Airplane
upward
pay attention to the
gap direction nut
A9
A9-1
A10
A11
steel wire push rod
nuts
insert
D5
A6
Wheel stopper A7
A2
A4
A4

10.Paste the vertical and horizontal tail D3 (as picture
shown below)
11.Connect the both JST plug together respectively
from tail wing and fuselage tail.
12.Paste the D7 in the middle of the fuselage,insert the
push rod through the guiding tube,pull the tube through
the D7 hole till fuselage tail;The right push rod comes
out from the right side board and the Z-shape end face
the tail.
13.Paste the A8 onto the D4,take care to aim the
preserved hole,paste the D4 and tail wing onto the tail of
the fuselage by foam glue;The left push rod comes out
from the upper hole of the D4(as picture shown).
Night Devil Instruction Manual EPP Airplane
D7
right push rod comes out
left push rod comes out
14.Paste the D2 onto the head of the fuselage by foam
glue,insert the wood sticks through the preserved hole
of the cabin.
15.Install the servo inside the cabin,install the servo arm
and EZ-connector,and connect the EZ-connector with
push rod.
16.Install the horn on the horizontal and vertical
tail,connect the servo horn with Z-shape push rod.
17.Paste together the wing D6,insert the carbon sheet in
the preserved slot and fix by foam glue.
18.Install the servo arm,paste the servo into the
preserved holes on the back of the wing by foam
glue,and insert the servo wires into the slot.
19.Install the servo horn onto the aileron,install the
EZ-connector onto the servo arm,plug the Z-shape push
rod into the servo horn,the other end connect with
EZ-connector.
D2
wood sticks
alignment hole A8
D4
Steering Wheel push rod
Steering Rudder
push rod
Elevator push rod
Embed the fortified carbon plate,
reinforce it with glue.
glue

22.Fasten the wing with rubber band onto the fuselage.
Adjust the C.G, C.G is 66mm from the leading
edge.Then start your flight.
C.G
≈66mm
Night Devil Instruction Manual EPP Airplane
20.Install and fix the propeller onto the motor.
21.Connection diagram for remote switch,electronics and LED plugs.
*connection diagram for remote switch
This is the battery cabin at the bottom of the
fuselage,you need to bind the battery by ribbon.
Set the remote switch signal on the
second gear of any driving lever,move
the driving lever could turn on or off the
switch;Once connected,you could turn
on or off the LED lights during flight.
F 2（ JST extension wire）
JST plug for
connecting the wing.
connect with LED JST connector
connect with remote
switch JST connector
connect the remote
switch power supply
(12V) with battery
F1(remote switch)
remote switch
3S Battery
ESC
JST connector
balancing
connector LED strips
Rx.