Dancing Wings Hobby 1.6M Fieseler Fi 156 Storch User manual

  
S21

飞行参数
Specification
翼展:1600mm（63inch）
机长:1000mm（40inch）
起飞重量: 1.7-1.9kg
推荐配置
Suggested Equipment
推荐马达: 2814-2820 KV800-1000
推荐桨叶: 10-12寸
推荐电调: 40A
推荐舵机: 9gx8pcs
推荐电池 4S 2200-2800mAh
推荐6通道以上接收机
舵机延长线15cm 6根
Y线 3根
舵机反向器 2个
选配配件
Optional Parts
Servo extension wires 6pcs
Y-wire 3pcs
Servo Reverser 2pcs
Wingspan: 1600mm（63inch）
Fuselage Length: 1000mm（40inch）
Flying Weight: 1.7-1.9kg Suggested Motor: 2814-2820 KV800-1000
Suggested Propeller: 10-12inch
Suggested ESC: 40A
Suggested Servo: 9gx8pcs
Suggested Battery: 4S 2200-2800mAh
Radio:more than 6CH
The Fi-156 was created as a reconnaissance, liaison and air-ambulance aircraft in 1936 by Dr. Gerhard Fieseler. This unique
airplane’s legs, struts and windows stuck out everywhere, and its landing gear hung down, looking very much like a long-legged,
big-winged bird, so it was given the nickname “Storch” (the German word for stork).
Virtually nothing about a Storch is streamlined. It was a purpose-built, short takeoff and landing (STOL) aircraft which, with a bit of
headwind, could become airborne in less than 200 feet, and when its low landing speed was combined with a strong headwind,
the Storch appeared to land vertically, and sometimes looked like it was flying backwards.
Fi-156于1936年由Gerhard Fieseler博士设计为侦察，联络和空中救护飞机。这架飞机有着独特的起落架，从支柱和窗户向外伸出，它的起落
架垂下，看起来非常像一只长腿的大鸟，所以它被赋予了绰号“Storch”（德语中的鹳）。
几乎没有任何关于Storch的简化。这是一架专门建造的短距离起飞和降落（STOL）飞机，在逆风时，可以在不到200英尺的高空飞行，当它以
低速着陆与强逆风相结合时，Storch几乎可以垂直降落，有时看起来像向后飞。
历史背景
● 这个产品不是玩具，而是一个复杂的具有难度的飞行器。您和您身边人的安全取决于您如何操作它，您需要了解相关知识，并谨慎操作。禁止
没有成人陪伴的儿童独自操作该设备。不适合14岁以下人群使用。再次强调，这不是一个玩具。
● This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends
on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be
accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A
TOY.
● 不要在机场，军事基地，居民区或其他任何受限制的地方飞行。
● Do not fly around some restricted location like airports, military bases, residential areas, etc.
● 您需要对发射机进行距离检查，以确保没有收到任何干扰。
● You will need to range check the transmitter to be sure you are not experiencing any interference.
● 始终保持先打开发射机后打开接收机，先关闭接收机后关闭发射机的步骤。
● Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.
● 如果您是初学者，建议您在有经验玩家的协助下调试和飞行。
● If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from
advanced expert fliers.
● 请将相关物品放置在孩子们够不到的地方
● Keep relevant items out of reach of children.
● 这个设备的设计已经超过我们正常使用所需要刚性要求，但若您需要以超出我们推荐的动力飞行时，请合理控制动作幅度并适当增加机体强度。
● This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform
any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body
strength.
● 您的设备中可能包括一些玻纤和碳纤雕刻的部件，这些纤维部件所带的粉尘可能会引起眼睛，皮肤的不适，请您在需要的时候带上护目镜或者防尘服。
● This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the
goggles or dust-proof clothes when needed.
● 因航空运输安全管制，您收到的产品可能没有清单中出现过的胶水，请您理解无法发送胶水给您的原因。您可以在当地文具店很方便的购买到您所需要
的胶水。
● Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the
glue you need at your local stationery store.
Balsawood Airplane
注意事项
SAFETY PRECAUTIONS
http://www.dwhobby.com/
Historical Background

散件 KIT
F13
F13-1
F13-2
爪牙螺母
claw nuts
F13-2+爪牙螺母
F13-1（底部 Bottom）
F3
F2
F20
F20
F19
F1
F14
安装另一边的侧板F1，同时安装内侧的F14加强件。
Install the side board F1 at the other side,and install
the inner board F14 as reinforcement.
F18-3
F18-1
F18
F18-1
F18-6F18-7 F18-5
F18-1
F18
F17*2
F17
F25 F17
F15
F2-1*2
F16
F21-1
F21
F6-1
F6-1
F22 F11
F4-2
F4-1
F26
F22-1*2
螺丝拧入预留孔，用螺丝固定PVC片，PVC在窗户背面。您可以完成蒙皮后再拎入螺丝。
Screw the screws into the reserved hole and fix the PVC piece with screws. The PVC
is on the back of the window. You can cover the film and then screw in the screws.
T1
T2
T3 T4
M2
M1
T5
G1 G4
G2
G3
方碳管3*3*495mm
方碳管3*3*390mm
方碳管3*3*375mm
Square Carbon Tube
Square Carbon Tube
Square Carbon Tube
轻木块
F1
F4*2 F5*2
F6 F7 F8 F9 F10
轻木条
Balsawood Strip
注意：进行拼装时，用美工刀从板材下取下各部件，用快干胶水
定型，用白乳胶加固。
Note:While assembling,take down the parts
from the board by knife,pls use the fast dry adhesive as
stabilization and whitelatex as reinforcement.
配件图仅做参考用，您收到的实物可能
因为修改/优化的原因导致与图片有略有
不同。
Photos shown here just for
reference, the product you received
maybe slightly differ from the
photos due to continuous
improvement on products.
工具 Tools Needed
01 机身组装
Assemble the Fuselage
01-1
01-2
01-3
01-4
01-5
01-6
01-7
01-8
01-9
01-10
01-11
01-12
        
1
磁铁
磁铁
Magnet
Magnet
Balsawood Block

F18-6
F18-7
F18-5
轻木条
Balsawood Strip
Balsawood Strip
W17
F1-1
F27
F27
F23
F4-5
磁铁
Magnet
反面 Back正面 Front 机翼组装 Assemble the Wing
尾翼组装
Assemble the Tail
F4-3
F4-6
磁铁
磁铁
磁铁
磁铁
U12
U10U10
U8
U9 U9
U10
U10
U8
U9
U9
机翼组装参照1：1图纸组装，拼装时在平面工作台进行，并保持机
翼平直。部分细节见细节图。
The wing assembly is assembled as per a 1:1 drawing, which
is carried out on a flat table and keeps the wing straight. See
the details for some details.
M1
碳管 Ø12*700mm
碳管 Carbon Tube 6mm*85mm
碳棒 Carbon Rod 3mm*105mm
安装机枪时先把U12用螺丝固定
到舱罩，再对插枪管和枪柄。
When installing the machine gun,
first fix the U12 to the cover, then
insert the gun and grab the
handle.
The cabin cover M1 should be trimmed
and assembled as per the shape of the
fuselage
机舱罩组装根据机身形状修剪仓身罩M1
        
2
01-13 01-14
01-16
01-17
02 机翼，尾翼组装
Assemble the Wing and Tail
W27
W28
W27
W24
W25-4
W25
W23
W22
W21
W25-2*4
W21-1*4
W25-1 W26
W21-1*2
机翼连接件组装 Assemble the Wing Connector
机翼连接件安装完成后，需根据外形轮廓打磨圆滑，参考下图示范。
After the wing connector is installed, it needs to be polished according to the
contour. Refer to the following picture for reference
碳管10mm*27MM
碳管12mm*35MM
02-1
02-2 02-3
02-4 02-5
01-15
02-6
W7-4 W7-5
W7-3
W7-1
W7-2
W7-1
长 Long
短 Short
细节1
Detail 1
细节 2
Detail 2
A7
A2
A11*2
打磨
Polish
A10
A9
A12
A3
A14
A5
A3
A7
A4
A4
A6
桐木条 7x11.5x357mm
轻木条 7x11.5x362mm
桐木条 3x3.5x357mm
轻木条 6x9x700mm
A14
A15
A15
襟翼，副翼，可变前缘组装
Assemble the Flap,Aileron and Movable Leading Edge
副翼 Aileron
襟翼 Flap
可变前缘
Movable Leading Edge
剖面图
Sectional view
前缘，副翼，襟翼拼装完成后，需打磨平滑，
打磨时参考剖面A15,A4形状。
After the leading edge, aileron, and flap are
assembled, polishing is required. Pls refer to
the section shape A15 and A4 while grinding.
02-7
02-8
水平尾翼
Horizontal Tail
02-9
尾翼参照1：1图纸进行拼装，
在拼装时使机翼平直。
The tail is assembled as per a 1:1 drawing, making
the wing straight during assembly.
02-10
垂直尾翼
Vertical Tail
Magnet
Magnet
Magnet
Magnet
Carbon Tube
Carbon Tube
反面 Back
正面 Front
Carbon Tube
Paulownia
Paulownia strip
Balsawood Strip
剖面图
Sectional view

U14
U16
橡胶套
Rubber sleeve
U14
U13
U15
U6
U4 U5
航灯
Navigation light
驾驶座
Driver's seat
天线
Antenna
T4
此部位先不粘固
Do not stick this part first
胶水粘合固定
Glue bonding
螺丝+螺母
Screw+nut 螺丝+螺母
顶面
T1
T1
T5*2
螺丝+螺母
此处螺丝固定T1，螺丝拎到步骤
01-1的爪牙螺母上。
Screw the T1 here and screw it
onto the claw nut of step 01-1.
此处自攻螺丝拧到步骤02-6细
节2的轻木条上。
Scew the self-tapping screws
onto the balsawood strip of
02-6 Detail 2.
螺丝
Screw
螺丝
T5*2
自攻螺丝
碳管 8mm*170mm
碳管 10mm*600mm
碳管 10mm*110mm
碳棒 Carbon rod 2mm*25mm
碳管 2mm*51mm
碳管 Carbon Tube 6mm*130mm
碳棒 Carbon Rod 1.5mm*120mm
碳管 Carbon Tube 3mm*190mm
碳棒 2mm*25mm
U1
U2
副油箱
Auxiliary tank
另一边机翼相同步骤安装，安装完后机翼保持平直。
The other wing is installed in the same step, and the
wing remains straight after installation.
        
3
03 像真件组装
Assemble the scale parts
04 Assemble the horizontal and vertical tails
水平尾翼，垂直尾翼安装
03-1
03-2
03-4
03-3
L10
L6
L6
L8
L8
T3
切 开
Cut open
自攻螺丝
另一边相同安装
Same installation
on the other side
支架拼装完成后，需打磨平滑，
打磨时参考剖面L8形状。
方向舵，和升降舵通过纸合页连接到尾翼，如图所示。安装好后使舵面可以
自由摆动。
The rudder and the elevator are connected to the tail through a paper
hinge as shown. After installation, the rudder surface can swing freely.
After the bracket is assembled,
it needs to be smoothed and
polished. When grinding, refer
to the section L8 shape.
04-1 04-2
04-3 04-1
05 Assemble the Wing and Tail
机翼安装
05-1 05-2
05-3 05-4
05-5 05-6
05-7 05-8
05-9
安装垂直尾翼与机身保持垂直，安
装水平尾翼与机身水平并居中，调
整好后再用胶水粘合固定。
The vertical tail is installed
perpendicular to the fuselage,
and the horizontal tail and the
fuselage are horizontally
centered. After adjustment,
glue and fix it.
Carbon Tube
Carbon Rod
Self-tapping screws
Carbon Tube
Carbon Tube
Carbon Tube
反面 Back
Screw+nut
Screw
Screw+nut
Self-tapping screws
自攻螺丝
Self-tapping screws

W29
W30
W30 W30
W31
W30
螺丝+螺母
螺丝+螺母
可变前缘连接舵机
注意舵角方向（如图朝向）
Pay attention to the direction of the servo horn (as shown)
可变前缘舵机
襟翼连接舵机
快装接头
襟翼舵机
舵机线由此导入机身
副翼舵机
L2
L1
L3
L4
G1 G2
轮挡（固定）
wheel block (fixed)
G2
轮挡
wheel block
轮挡
wheel block
轮挡
塑料扣+自攻螺丝
Plastic buckle +
self-tapping screws
G3
短 Short
长 LongG3
G3
G2
自攻螺丝
轮挡
        
4
W32
W32
W32 螺丝+螺母
此处组装完成后，需打磨
平滑，参考截面形状。
After the assembly is
completed here, it needs
to be smoothed and the
reference section shape
is required.
06 Assemble the Landing Gear
起落架安装
后起落架安装
Assemble the Rear Landing Gear
06-1
06-2 06-3
06-5 06-4
拼装打磨好后，2片合
在一起，夹住G2，调
整好位置，用胶水粘合
住。
After assembling and
polishing, the two
pieces are put
together, the G2 is
clamped, adjust the
position and glue it.
尾轮的钢丝插入垂直尾翼，用胶水粘合固
定住，使尾轮可以随尾翼转动。
The steel wire of the tail wheel is inserted
into the vertical tail and fixed with glue
to make the tail wheel rotate with the tail.
G1插入机身，用胶水粘
合固定，G2插入机身后
在内部用轮挡锁定。
G1 is inserted into
the fuselage and
glued, G2 is inserted
into the fuselage and
locked inside by the
wheel block.
06-6
07 Assemble the movable leading edge,flap and aileron
可变前缘，襟翼，副翼安装
08 Install the servo inside the wing
机翼内舵机安装
wheel block
Self-tapping screws
wheel block
Screw+nut
Screw+nut
Screw+nut
The servo wire is thus
introduced into the
Flap servo
Movable leading
edge servo
Aileron servo
快装接头
EZ-Connector EZ-Connector
Movable leading edge connecting servo Flap connecting servo 副翼连接舵机 Aileron connecting servo
另一边相同安装
Same installation
on the other side
快装接头
EZ-Connector

此处安装舵机需用桐木块垫起一定高度
Here the servo should be installed with a
paulownia block to a certain height.
用桐木杆和Z型钢丝制作连杆，如下图，一端为Z型，一端为直头，用线绑
扎，胶水粘固。制作时对比机身内舵机到尾部舵角的距离，调整连杆长度。
The connecting rod is made of paulownia rod and Z-shaped steel wire,
as shown in the following figure, one end is Z-shaped, one end is
straight, tied with wire, and glue is glued. Adjust the distance between
the servo and the tail rudder angle in the fuselage during production,
and adjust the length of the connecting rod.
快装接头
水平尾翼连接舵机
M4
M2R
M3
轻木条
M1L
M5
M0玻纤+M0*2
自攻螺丝
自攻螺丝拧
到轻木条上
Screw the
self-tapping screws
onto balsawood
self-tapping screws
电机安装示范，电机座根据所选电机调整伸出长度，
调整好后用角型铝件固定住。
Motor installation demonstration, the motor mounting
adjusts the extension length according to the selected motor,
and after adjustment, it is fixed by the angle aluminum piece.
        
5
09 Assemble the servo inside the fuselage
机身内舵机安装
10 Install the Motor Mounting and Motor
电机座及电机安装
此处轻木条根据马达座与
角型铝件结合的位置调整
自攻螺丝
11 Install the scale parts
像真件安装
此机型结构为电动马达设计，如您需要安装油动引擎，我们为您提供了2
块油动引擎防火墙，安装需要一定的改装和加固，需要您自己动手修改。
This model is designed for electric motor. If you need to install the
oil engine, we provide you with 2 oil engine firewalls. The installation
needs certain modification and reinforcement. You need to modify it
yourself.
EZ-Connector
Vertical tail connecting servo
垂直尾翼连接舵机
Horizontal tail connecting servo
Here the balsawood strip
is adjusted according to
the position of the motor
mounting and the angled
aluminum piece.
fiberglass
self-tapping screws
另一边相同安装
Same installation
on the other side
Balsawood Strip

重心位置展示
C.G
≈70-75mm
电子设备接线图
Wiring Diagram for Electric Equipment
12 Set and Adjust
设置和调试
常规飞行(Normal Flying) 3D飞行 部分飞机支持(3D Flying only support some models)
副翼 Aileron ±（15°-30°） ±40° 或者更大(or larger)
平尾 Elevator ±15° ±40° 或者更大(or larger)
垂尾 Rudder ±15° ±40° 或者更大(or larger)
常用襟翼 Flap （起飞 take-off）15°-20° （降落 Landing）20°-40°
        
6
部分特殊机型会有V型尾翼，襟翼，前缘机翼或舵面很小等，可以以常规飞行的角度作为参考，在您不确认且没有有经验人员指导
的情况下，我们建议您先以小角度试飞以确认您的设置是否正确。
Some special models will have V-tails, flaps, leading edge wings, etc., which can be used as a reference for conventional
flight angles. If you do not confirm and there is no experienced person to guide you, we recommend that you first test
at a small angle to confirm that your settings are correct.
RudderElevator
Aileron
15°-30°
15°
15°
15°
15°
15°-30°
通常情况下，舵面角度的设置如下：
Usually, the control throws set as below:
≈70-75mm
Display the C.G
CHCHCHCHCHCH
ESC
电调
接收机
Rx.
电池
Battery
舵机反向线
Servo Reverser
Y线
Y-wire
Y线
Y-wire
升降舵
副翼
方向舵

Control Directions Tests
● 安装舵机前，请先将舵机通电让舵机中心点回中，以便能更好的调试舵面。
● Check/adjust servo centering, in order to adjust the control surface better.
● 初次启动电机，您需要确认电机旋转的方向以适配您的机型。
● Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.
● 请将重心（CG）调整至说明书所述位置并尽量靠近。如果有需要，您可以增加机头或者机尾的重量，以确保机体有更
好的飞行姿态。
● Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to
the nose or tail to ensure the best flight performance.
● 检查机身内部，确保所有设备正常连接；检查机身表面，包括但是不限于蒙皮，固定螺丝，舱盖，座舱罩等位置。
● Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the
heat-shrink covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.
● 在飞行前，请检查您电池情况，若有低电压，电池损坏等情况，请您停止操作并马上更换电池。
● Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found
low voltage or damage to battery.
● 机身内部设备连接的方式，会和您的收发设备有关，在一些功能更多的收发设备上，您可以通过设置简化机身内部设
备的连接。详细请查看您的收发设备以确认是否满足您需要的功能。
● The way the internal devices of the fuselage are connected will be related to your transmitter-receiver
device. For those transmitter-receiver devices with more functions, you can simplify the connection of the
internal devices of the fuselage. Check your device for details to see if it meets the features you need.
● 动力设备和收发设备第一次配对时，可能需要设置油门最大行程，请您自行设置。
● When the power system and transmitter-receiver device are paired for the first time, you may need to set
the maximum stroke of the throttle. Please set it yourself.
飞行前的建议
PRE-FLIGHT CHECKS
        
7
Elevator
升降舵
方向舵
副翼
AileronRudder
遥控器动作 飞机反应
升降杆下拉
Direction rod to the left
升降杆上推
Direction rod to the right
Steering rod to the left
Steering rod to the right
Lifting rod up
Lifting rod down
转向杆向右
转向杆向左
方向杆向右
方向杆向左
地面控制方向测试