Dancing Wings Hobby VX14 User manual

VX14 BLERIOT XI INSTRUCTION MANUAL
材质 Material:
1. 椴木 Basswood
2. 巴尔莎木 Balsawood
3. 桐木 Paulownia
4. 碳杆和其他
carbon rod and others
工具 Tools Needed
各部件用美工刀从板材上取下，按下图图示及步骤拼装，木质部件建议用
快干胶(502)定型，用白乳胶加固。
Pls take down the parts from the board by knife,and assemble
them as per the procedures as below,we suggest you to shape
with 502 glue,and firm withwhite latex.
1.机身组装 Fusalage Installation
L
W
B
1.1 1.2
1.3
1.4
1.5
1.6
1.7
2.1 2.2
2.3
1.8 1.9
2.机轮及滑橇组装 Landing Gear Installation
2.４ 2.5
3.机翼组装 Wing Installation
4.尾翼组装 Tail Assembly
2.6
3.1
3.2
3.3
3.4 3.5
3.6
4.1 4.2
C1
C1
D1
U1
F4
F6
C2
C2
F7
F8
F9
F5
F3
F3 F3-1
F3-1
F3-1
B
B
F2F1
F11
F13
G1
G1
G2-1
G2
F14
F15
F12
粘C2上端板时调整机身后端角度。
Adjust the rear angle of the fuselage
when you stick the C2 upper plate.
在平整工作台面拼装L1-L3，保持机翼平直。
Assemble L1-L3 on a flat work desk and
keep the wing straight.
左右机翼拼装方法相同，注意:请对称拼装，不要拼成顺边。完成后机翼相对插到机身。
The left and right wings are assembled in the same way.Note:please assemble symmetrically
instead of along the edge.After completion,insert the wings into the fuselage
从LX取下木条，安装到机翼翼梁卡口内，按实际长度截取。
Remove the wood strip from LX, install them into the wing
beam bayonet, and cut them according to the actual length.
截取1根83mm 碳杆，如图安装。
Cut one 83mm carbon rod and
assemble as picture shown.
注意：此处机轮为可转动设计，请勿粘固机轮。
Note: the wheel is rotatable ,please do not stick the wheel.
对齐
Align
G10
G3
G4
G3
G3
G4
G3
W
组装2个
Assemble 2 pcs
组装4个
Assemble 4 pcs
G5 G8 G9
G9
G6
F7
L1
L3
L2
W1
F10
R1
R2
W1
W1
W1
W1
W1
W1
W1
W3
W4
W5
W2
F8
12mm
不粘 Non-stick
粘固 Stick 粘固 Stick
正面
front
背面
back
F4粘到机身末端，对齐两侧板。
Stick the F4 to the fuselage end, and align the
2pcs side plate.
对齐
Align
截取2根70mm 碳杆，如图安装。
Cut two 70mm carbon rods
and assemble as picture
shown.
按实际长度截取3根短木杆，如图
粘贴安装并打磨棱角。
Cut three short wooden rods
by actual length,paste as
picture and polish the edges.
截取20mm 碳杆，
如图安装。
Cut one 20mm
carbon rod and
install as picture
shown.

5.螺旋桨组装 Propeller installation
6.拉线安装 Wiring Assembly
4.3
4.4
5.1
5.2
5.3
5.4
5.5
4.5
6.1
6.2
6.3
E1
E2 E3
E3
E2E2
截取130mm 碳杆，如图安装。
Cut one 130mm carbon rod and install as
picture shown.
居中粘贴尾翼到机身。
Paste the tail to the fuselage in the middle.
粘固
Stick
不粘 Non-stick
M1 M2
切除
Cut off
a1
a2
b2
b3
a3
b1
顶部4条拉线
4pcs wirings on the top
a1-a2 a1-a3
b1-b2 b1-b3
底面4条拉线
4pcs wirings on the bottom
a4-a2 a4-a3
b4-b2 b4-b3
a4
a2
a3
b2
b3
b4
a1
c1 d1
c2 d2
b1
6.4
支架处4条拉线
4pcs wirings at the bracket
a1-d1 a1-d2
b1-c1 b1-c2
6.5
6.6
e1
f1
f2
f3
f4
f5
f6
f7
e2
e3
e4
e5
e6
e7
6.7
g1
i1
j1
j2
j3
j4
j5
i2
i3
i4
i5
h1
h2
h3
h4
h5
h6
g2
g3
g4
g5
g6
组装2个
Assemble 2 pcs
组装好的引擎粘贴到机头部标记处。
Paste the assembled engine to the
marking head of plane.
e1-e2-e3-e4-e5-e6-e7 f1-f2-f3-f4-f5-f6-f7
机身左侧，右侧各2条拉线，此处以左侧为例,右侧相同安装。
2pcs wirings each on the left and right side of the fuselage,here
is an example of left side,the installation method is same for
right side.
g1-g2-g3-g4-g5-g6 h1-h2-h3-h4-h5-h6
机身上端2条拉线
2pcs wirings on the upper fuselage
机身下端2条拉线
2pcs wirings on the lower fuselage
i1-i2-i3-i4-i5-i6 j1-j2-j3-j4-j5-j6
机翼拉线左右两边相同安装，此处以单边为例展示。
The left and right wirings are installed in the same way. Here take
one side as an example.
截取1根15mm 碳杆，如
图安装。
Cut 15mm carbon rods
and assemble as
picture shown.