Dancover 2m Series User manual

12-02-2018
2m Series
Manual
for
Work Tent

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is
your responsibility to comply with local rules and regulations and to ensure that the
marquee/tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is
safely secured and that the marquee/tent does not cause damage to others.
close to the tent.
The marquee/tent must be safely secured. We recommend you secure your marquee/tent
with straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents
insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow always remove snow from the roof of the marquee/tent regularly to
prevent snow from building on the roof as heavy snow can cause the marquee/tent to
collapse.
In the event of rain there is a risk of rain puddles building up on top of the roof of the
marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility
to ensure rain puddles do not build up. As a precaution, make sure the roof of the
marquee/tent is stretched out properly and adequately over the side frames of the
marquee/tent and remove rain water regularly.
Do not unpack or repack your marquee/tent in freezing temperatures. In case of
temperatures below zero always unpack and repack your marquee/tent indoors to avoid
the risk of cracking parts.
The marquee/tent must be totally dry before you repack and store it to avoid mildew.
Warranty Information
Please visit dancovershop.com for information on warranty.
Please always check our website for the latest safety advice and manuall.

Assembly manual
DEAR CUSTOMER
Assembly with more than one person suggested.
Please use gloves when assembling the metal frame portion of this unit.
The metal components of this product have been treated
with a rust preventive coating that may feel oily to the
touch. This coating is not dangerous, but may dirty your
hands during assembly. We recommend that you wipe
metal parts clean with a mixture of warm water and dish
detergent prior to assembly. Should your hands become
dirty, simply wash with soap and water.

2m Part list
PART NO. DESCRIPTION QTY
2m 3m 4m
No.1 Back leg 2 2 2
No.2 Regular Leg 4 6 8
No.3 corner arch 6 8 10
No.4 Center arch 3 4 5
345
No.5 Cross bar
No.6 Diagonal 2 2 2
No.7 Connecting Pipe 5 5 5
No.8 Connecting Pipe 5 10 15
No.9 Anchoring Bracket 4 4 4
No.10 Anchoring rod 4
8
16
4 4
No.11
No.12
1-3/4" Bolt 10 12
2-1/2" Bolt 21 26
No.13 Wing Nut 24 31 38
No.14
Cover 1 1 1
12-02-2018

1. Assembly of middle arches
a) Take one arch (no. 4); assemble with one main corner arch
(No.3) on the left side.
b) Take the other corner arch (no.3) on the right side.
c) Take one completed arch; put screw 1-3/4" (No.11) through
holes on the right side and attach bar ( no.5) over screw and
tighten wing nut(No.13)
d) Repeat same procedures on the left side.
2. Repeat step 1 for the remaining middle arches.
3. Assembly of end arches (Wing nuts are always on inside of
the shelter)
a) Take one arch (No.4); assemble with one corner arch (No.3) on
the left side.
b)
c)
Take the other corner arch (No.3) on the right side.
Repeat step 3 with the remaining arch.
d) Place one of the last arches assembled at the front of the
shelter, the other at the back.

4. Assembly of legs
a) Insert (No.1) legs into an end arch one side at a time.
b) Insert (No.2) legs to the second arch.
c) Add second arch to assembly connecting (No.8) into (No.7) and
diagonal bar (No.6) with screws 2 ½” (No.12) with wing nuts
(No.13). See sketch at front page. Note: (06-374) should be
placed at last section.
d) Repeat step b) and c) until the whole shelter is completed.
e) Make sure the base is open to 2m.
f) Make sure the distances AD and BC have exactly the same
length as per illustration, lengths depends on the model.
5. Cover installation (Ties are always on the inside)
a) Place the roof in front of the shelter as illustrated.
b) Unfold as illustrated then lift onto shelter as is.
c) Place cover over the completed structure making sure that the
TRIANGLE is at the front of the garage.
d) Attach all straps inside the roof ot the structure poles going
completely around the garage.
e) Tie firmly inside ties to bars.
6. Anchoring garage.
a) Place your garage in the final position you want then close the
doors, front and back if supplied before anchoring, anchor with
brackets (No.9) and nail (No.10) as per diagram on the first
page. Drive anchor into ground.
b) Fix flap to your house (if applicable).
A
B
C
D
2m

Contact information
Head office:
Dancover A/S
Nordre Strandvej 119 G
3150 Hellebæk
Denmark
For more information
please visit:
www.dancovershop.com
National contact
Denmark: 70 26 76 20
[e-mail]
UK: 020 8099 7570
[e-mail]
Spain: 911 436 828
[e-mail]
Italy: 02 479 21 198
[e-mail]
Germany: 041 0266 7040
[e-mail]
Switzerland: 0840 000125
[e-mail]
France: 0975 181 800
[e-mail]
Austria: 0662 626935
[e-mail]
Sweden: 040 233 262
[e-mail]
Finland: 0 931 581 720
[e-mail]
Nederland: 0 858 880 524
[e-mail]
Poland: 22 300 8602
[e-mail]
Ireland: 0 151 33 003
[e-mail]
Luxembourg: [phone]
[e-mail]
Portugal: 308 800 899
[e-mail]
Belgium: 0 28 08 08 09
[e-mail]
Norway: 231 00 690
[e-mail]