Dancover Pagoda Tent PRO+ 10x10m EventZone User manual

15-05-2019
for
Pagoda Tent PRO+
10x10m EventZone
Manual

1

1.) Take the eave-connector (1) and a ridge piece (2), slide the beam (3) over
the square tube at the eave-connector (1) on the ridge-piece (2) until it covers
the drilling. Fit through the M16x90 bolt and bolt them together
1
1
2
1
1
2
3
3
3
3
3
3
2

2.) Take the beam (5) with the already fixed inserts (5a). Slide the beam over
the square tube at the eave connector (4) until the drill is covered, fix the
M16x90 bolt and screw it together. Hang the beam (5) with the insert (5a) on
to
the ridge-piece (2) by fixing to bolt (6) through the it.
4
4
5
5a
5
5a
5a
5
4
4
5
2
4
5
5a
6
6
3

3.) Take the beam (5) with the already fixed inserts (5a). Slide the beam over
the square tube at the eave connector (4) until the drill is covered, fix the
M16x90 bolt and screw it together. Hang the beam (5) with the insert (5a) on
to
the ridge-piece (2) by fixing to bolt (6) through the ridge-piece.
7
8
9
9a
9
8
9a
9a
6
2
7
8
9
4

4.) Slide the eave-purlin (10) over the eave-connector (1), (4) and (7) until the
drilling is covered, fit the M12x90 bolt and screw them together. In case the
eave-purlins (10) can not be slid on the corners, loose the connection at the
eave connection (7) to the beam and slide the eave-purlin (10) as well as the
beam (8).
10
10
10
7
7c
4
4
1
1
10
10
10
10
7
5

5.) Take the mast (11) and slide it from top into the ridge-piece (2) fix the top-
cap (12) over the tube.
11
11
12
12
12
11
2
6

6.) Fit the top-cap (5) over the mast (11). Put the roof cover on the frame. Pull
the hooking track device (13) in the channel of the roof cover (14) on all sides.
Hook the track (15) in the eave purlin (10).
13
13
14
10
10
15
7

+
7.) To tension the cover you have to use the pulley (18) by hanging the hook
(18a) onto the ring bolt(16). Take the hook (18b) and hang it on the ring bolt
(17) on the mast (11), now pull the chained (19) until the requested tension is
reached. Fit the bolt (20) into the mast (11), remove the pulley (18).
2
16
11
17
18
18a
18b
19
20
2
8

8.) Lift the frame, slide the 8 legs (21) over the eave-connector (1), (4), (7)
until the drilling is covers in full. Bolt the connection by use of the M16/90 bolt
(22) together. Fix the foot-bolt in the base-plate (23) by. Lower the total frame
to the ground.
21
21
21
21
21
21
7
7
23
22
21
9

9.) Fit the door-part (24). Fix the walls (27) in. Hook the u-profiles (25) to the
door parts (24). Slide the door in the u-profiles, fit the next door-part and fix
the 2nd u-profiles and slide it to the door, now you can fasten the door-post to
the eave purlin.
24
24
24
25
27
26
26
26
26
10

9.) Put the legs straight. Secure the tent by knitting in the anchors to the holes
of the baseplate. The pagoda comes with 16 ground-anchors.
28
28
28
28
28
28
23
23
23
11

Contact information
Head office:
Dancover A/S
Nordre Strandvej 119 G
3150 Hellebæk
Denmark
For more information
please visit:
www.dancovershop.com
National contact
Denmark: 70 26 76 20
[e-mail]
UK: 020 8099 7570
[e-mail]
Spain: 911 436 828
[e-mail]
Italy: 02 479 21 198
[e-mail]
Germany: 041 0266 7040
[e-mail]
Switzerland: 0840 000125
[e-mail]
France: 0975 181 800
[e-mail]
Austria: 0662 626935
[e-mail]
Sweden: 040 233 262
[e-mail]
Finland: 0 931 581 720
[e-mail]
Nederland: 0 858 880 524
[e-mail]
Poland: 22 300 8602
[e-mail]
Ireland: 0 151 33 003
[e-mail]
Luxembourg: [phone]
[e-mail]
Portugal: 308 800 899
[e-mail]
Belgium: 0 28 08 08 09
[e-mail]
Norway: 231 00 690
[e-mail]