Danfoss CVP User manual

Installation guide
Pilot valves
CVP, CVPP, CVC, CVE and EVM
027R9594
027R9594
© Danfoss | DCS (MWA) | 2017.03
DKRCI.PI.HN0.P3.02 | 520H10898 | 1
CVP
CVPP CVC
CVE
EVM NC EVM NO
Fiber:
x3 - ICS3
x1 - ICS1
CVP, CVPP, CVC, CVE,
EVM NC & EVM NO:
50 Nm (35 ft-lbs)
32 mm
(1¼ in.)
O-ring
CVP, CVPP, CVC:
10 Nm (7 ft-lbs)
CVPP, CVC:
40 Nm (28 ft-lbs)
CVPP:
50 Nm (35 ft-lbs)
WWYY (Week/Year)
Product label:

© Danfoss | DCS (MWA) | 2017.03
DKRCI.PI.HN0.P3.02 | 520H10898 | 2
Range Range Factory setting 1 Rev (360°) ~
-0.66 →7 bar 19.5 in Hg →102 psig ~ 0.8 bar/11.6 psig 1 bar/ 14.5 psig
4 →28 bar 58 →406 psig ~ 12 bar/174 psig 3.1 bar/ 45 psig
25 →52 bar 363 →754 psig ~ 26.6 bar/386 psig 4.1 bar/ 59.5 psig
CVP
Range Range Factory setting 1 Rev (360°) ~
-0.66 →7 bar 19.5 in Hg →102 psig ~ 0.7 bar/10.2 psig 1 bar/ 14.5 psig
4 →28 bar 58 →406 psig ~ 7.6 bar/110 psig 3.1 bar/ 45 psig
CVPP
Range Range Factory setting 1 Rev (360°) ~
-0.66 →7 bar 19.5 in Hg →102 psig ~ 0.8 bar/11.6 psig 1 bar/ 14.5 psig
4 →28 bar 58 →406 psig ~ 12 bar/174 psig 3.1 bar/ 45 psig
CVC
Open Close
See installation guide
DKRCI.PI.HV0.K
CVE
-1
0
1
2
3
4
5
6
7
8
0% 20%40% 60%80% 100%
Non-setting area*
Non-setting area*
barg
0
14.5
29.0
43.5
58.0
72.5
87.0
101.5
psig
116.0
-29.5 in. Hg
ICAD reading (spring decompression)
barg -0.66 012345678
psig 19.5 in. Hg 0 14.5 29.0 43.5 58.0 72.5 87.0 101.5 116.0
mA 18.3 17.1 15.9 14.7 13.5 12.3 11.1 9.9 8.7 7. 5
ICAD reading % 90% 83% 75% 67% 60% 53% 45% 37% 30% 23%
CVE Pressure setting (see DKRCI.PI.HVO.J for ICAD setup)
* These areas are dedicated regulation band for the pilot. It is recommended not
to exceed the limits in above table
Valve sealingPacking gland leak tightening
(CVP, CVPP & CVC)
Max.
20 Nm (15 ft-lbs)