Daniela DAN64GTG User manual

Appliance User Manual
GAS ON BLACK GLASS COOKTOPS
DAN64GTG, DAN75GTG, DAN95GTG/2
DAN2GTG, DAN1GTG
danielaappliances.com.au

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 2
Daniela Appliances started in 1988. Formally known as Italnova,
the company began operating by selling other major leading brands.
Since then, Daniela Appliances has it’s own range, continuously
evolving, striving on delivering leading-edge quality products at
very competitive prices.
From an Italian heritage our brand Daniela was then established in
2005 from a father’s love to a daughter and naming it after Daniela,
now the new proprietor. Daniela has worked closely with her father for
many years learning from his decades of industry experience. Daniela
with her extensive knowledge and understanding of appliances, now
continues her father’s legacy with a modern flare.
Our products are extensively tested and come with ISO certification
certificates prior to importation. Daniela Appliances continuously
designs and sources the best parts, to bring you an elegant feel that
will last the test of time and for a third of the cost from a major brand.
Daniela Appliances is dedicated to offering our customers exceptional
products with exceptional service. Our commitment is to provide our
valuable customers the very best in technology with the very best in
safety that combines both the values that brings us market success.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 3
DAN64GTG
60CM 4 BURNER GAS GLASS COOKTOP
DAN75GTG
70CM 4 BURNER GAS GLASS COOKTOP
DAN95GTG
90CM 5 BURNER GAS GLASS COOKTOP

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 4
SAFETY PRECAUTIONS
BEFORE INSTALLING AND OPERATING THE HOTPLATE, READ THESE INSTRUCTIONS
COMPLETELY AND CAREFULLY!!
IMPORTANT - Save these instructions for the customer & local authority’s inspector’s reference.
IMPORTANT INSTALLATION - Observe all governing codes e.g. AS5601, council ordinances and
local authority rules.
IMPORTANT - The hotplate must be installed by an authorised person.
IMPORTANT - Remove all packing material and literature from the hotplate before connecting
the gas and electrical supplies
IMPORTANT TO THE INSTALLER - After connecting the gas supply, turn on the gas and check
for leaks at all the joints with soapy water or other approved methods.
UNDER NO CIRCUMSTANCE USE A NAKED FLAME IN CHECKING FOR LEAKS.
ELECTRICAL SHOCK HAZARD
• Disconnect the appliance from the mains electricity supply and gas supply before carrying
out any work or maintenance on it.
• Connection to a good earth wiring system is essential and mandatory.
• Alterations to the domestic wiring system must only be made by a qualified electrician.
• Failure to follow this advice may result in electrical shock or death.
SAVE THIS INSTRUCTION IN A SAFE PLACE FOR FUTURE REFERENCE
Thank you for choosing Daniela appliances!
Please read all instructions before using this appliance. This book contains valuable
information about operation, care and service. Keep it in a safe place for future
reference. Should the appliance be sold or transferred to another owner, or should
you move house and leave the appliance, always ensure that the book is supplied with
the appliance in order that new owner can be acquainted with the functioning of the
appliance and relevant warnings.
The manufacturer cannot be held responsible for any inaccuracies due to printing or
transcription errors that may be found in this handbook.
N.B.: the pictures shown in the figures in this manual are purely indicative.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 5
CUT HAZARD
• Take care - panel edges are sharp.
• Failure to use caution could result in injury or cuts.
OPERATING INSTRUCTIONS - WARNINGS
• Appliance to be operated only by competent persons. Do not allow children or the infirm
near or to operate this appliance.
• DO NOT MODIFY THIS APPLIANCE.
• DO NOT USE THIS APPLIANCE AS A SPACE HEATER.
APPLIANCES OPERATING ON L.P.G.
Where the hotplate is installed in marine craft of caravans, it must incorporate a flame
failure device.
• DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN
OPERATION.
• DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
• If the hotplate fails to operate correctly, contact Daniela Appliances Pty Ltd or their
approved service agents.
DO NOT ATTEMPT ANY REPAIRS OR SERVICE YOURSELF.
SERVICE TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON!
IMPORTANT SAFETY AND CARE INSTRUCTIONS
• Read these instructions carefully before installing or using this appliance.
• The manufacturer disclaims all responsibility if these instructions are not followed.
Should youhave any doubts, seek the assistance of an authorised person.
• No combustible material or products should be placed on this appliance at any time.
• Please make this information available to the person responsible for installing the appliance
as it could reduce your installation costs.
• In order to avoid a hazard, this appliance must be installed according to these instructions
for installation.
• This appliance is to be properly installed and earthed only by a suitably qualified person.
• This appliance should be connected to a circuit which incorporates an isolating switch providing
full disconnectionfrom the power supply.

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 6
To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:
• Call only Service Centres authorized by DANIELA APPLIANCES PTY LTD
• Always use original Spare Parts.
1. This appliance is intended for non-professional use within the home and it is intended
commencing date of purchase. Commercial warranty on Daniela Appliances are strictly
3 months from date of purchase.
2. After you remove the packing, check that the appliance is not damaged. If you have any
doubts, DO NOT USE OR INSTALL the appliance, contact Daniela Appliances Pty Ltd or
warranty options.
3. Never leave the packing components within the reach of children since they are a source of
potential danger.
4. The appliance must be installed only by a qualified person in compliance with the
instructions provided. The manufacturer declines all responsibility for improper installation
which may harm persons and animals and damage property.
5. The Appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervised instruction concerning use of the appliance by a responsible person
for their safety. Cleaning and maintenance operations must not be carried out by children
without supervision.
6. The electrical safety of this appliance can only be guaranteed if the appliance is correctly
and installed, in compliance with current regulations on electrical safety. Always ensure that
system. The manufacturer declines all responsibility for damage resulting from a system
which has not been installed correctly, plastic bags, foam polystyrene, nails, etc.
7. Check that the electrical capacity of the system and sockets will support the maximum power
of the hob, as indicated on the rating label. If you have any doubts, call in a qualified technician.
8.
9. The user must not replace the supply cable of this appliance. Always call an after-sales servicing
centre authorized by Daniela Appliances in the case of cable damageor replacement.
10. This appliance must be used for the purpose for which it was expressly designed. Any other
use is considered to be improper and consequently dangerous. The manufacturer declines
all responsibility for damage resulting from improper and irresponsible use.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 7
11. A number of fundamental rules must be followed when using electrical appliances
The following are of particular importance:
• Never allow the Mains Cable to be stretched or pulled. Do not use the appliance if the
Mains Cable is damaged, consult a qualified electrician.
• Do not modify or attempt to modify any of the characteristics of this appliance.
This would be dangerous to your safety.
• Do not leave the appliance outside under the sun, rain, etc.
• Do not touch any electrical appliance if hands or feet are wet or damp.
• Do not use the appliance bare footed.
• Do not allow the appliance to be used unsupervised by children or
persons unfamiliar with it.
• Do not use steam cleaners, as this may cause moisture build up.
•
• Always clean after every use to avoid build up and the necessity
of stronger cleaning products.
12. To avoid accidental spillage do not use cookware with uneven or deformed bottoms on
the burners or on the electrical plates.
13. Special care should be taken when using cheap pans etc. with care being taken to avoid
splashing or spillage of hot oil. They should not be used unattended since overheated oil
may boil over and could also ignite.
14. Parts of this appliance and its cooking surfaces, retain heat for considerable periods
cooled down.
15. When the appliance is in use, the heating elements become extremely hot. Make sure you
don't touch them and keep children well away.
16.
(If the hob surface is of glass-ceramic or similar material and protects live parts).
17. Do not cook on a broken or cracked cooktop. If the cooktop surface should break or crack,
qualified technician.
18.
19. Failure to follow this advice may result in electrical shock or death.
PLEASE ENSURE YOU READ THESE INSTALLATION GUIDES, RULES, TERMS AND
CONDITIONS BEFORE CALLING FOR A SERVICE, FAILURE IN DOING SO MAY RESULT
IN DAMAGES TO THE APPLIANCE AND JOINERY - CHARGES MAY BE APPLICABLE
AND WARRANTY WILL BE VOIDED.

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 8
WARNING!!
Failure to install the appliance correctly could void any warranty or liability claims.
HEALTH HAZARD
• This appliance complies with electromagnetic safety standards.
• However, persons with cardiac pacemakers or other electrical implants (such as insulin
pumps) must consult with their doctor or implant manufacturer before using this appliance
HOT SURFACE HAZARD
• During use, accessible parts of this appliance will become hot enough to cause burns.
• Do not let your body, clothing or any item other than suitable cookware be in contact
with the glass until the surface is cool.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob
surface since they can get hot
• Keep children away.
• Handles of saucepans may be hot to touch. Check saucepan handles do not overhang
other cooking zones that are on. Keep handles out of reach of children.
• Failure to follow this advice could result in burns and scalds.
CUT HAZARD
• The razor-sharp blade of a cooktop scraper is exposed when the safety cover is retracted.
Use with extreme care and always store safely and out of reach of children.
• Failure to use caution could result in injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS
• Never leave the appliance unattended when in use. Boil over causes smoking and greasy
spillages that may ignite.
• Never use your appliance as a work or storage surface.
• Never leave any objects or utensils on the appliance.
• Never use your appliance for warming or heating the room.
•
(i.e. by using the knobs or touch controls).
• Do not allow children to play with the appliance or sit, stand, or climb on it.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 9
• Do not store items of interest to children in cabinets above the appliance. Children
climbing on the cooktop could be seriously injured.
• Do not leave children alone or unattended in the area where the appliance is in use.
• Children or persons with a disability which limits their ability to use the appliance should
have a responsible and competent person to instruct them in its use. The instructor
should be satisfied that they can use the appliance without danger to themselves or their
surroundings.
• Do not repair or replace any part of the appliance unless specifically recommended in the
manual. All other servicing should be done by a qualified technician.
• Do not use a steam cleaner to clean your cook top.
• Do not place or drop heavy objects on your cooktop.
• Do not stand on your cooktop.
• Do not use pans with jagged edges or drag pans across the glass surface as this can
scratch the glass.
• Do not use scourers or any other harsh abrasive cleaning agents to clean your cooktop,
as these can scratch the glass.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
WARNING
• The appliance and the accessible parts of it will become hot during use. Be careful not to
touch the heated elements. Children must not be allowed to touch the appliance, unless
they are supervised continually.
• Only a qualified person in compliance with the instructions provided must install the
appliance. The appliance must be fully assembled as in normal operation without any parts
removed. Daniela Appliances Pty Ltd declines all responsibility for improper installation,
which may harm persons and animals and damage property.
•
WARNING!!
• Unattended cooking with fat or oil can be dangerous and may result in fire.
e.g. with a lid or a fire blanket.
• Danger of fire: do not store items on the cooking surfaces.

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 10
SAFETY WARNINGLABELSEXPLANATION
INSTALLATION INSTRUCTIONS
1. The requirements of the local Gas and Electrical authorities must be adhered to:
• Consult AS5601 (AG601) as appropriate
• Consult SAA Wiring rules for electrical installations as appropriate
2. Location of gas inlet
• ***64GTG located 125mm from left side at rear
• ***75GTG located 175mm from right side at rear
• ***95GTG located left side, 250mm from front 30mm in from edge.
3. Electrical connection
• 240mm C/L from RH side (as viewed from front)
• 40mm C/L from rear
• Connection is by means of flexible cord and plug.
MODEL HEIGHT WIDTH DEPTH
95GTG 75mm 865mm 510mm
75GTG 75mm 700mm 510mm
64GTG 75mm 600mm 510mm
4. Overall
dimensions
of hotplate
5. Daniela Appliances Pty Ltd and their appointed agents decline any responsibilities
in the case of installation is not according to these instructions.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 11
INSTALLATION
The cooktop is to be installed as detailed below.
• Remove any packaging, plastic film etc from appliance.
• Before placing the cooktop in position fit the foam sealing strip on the underside, around
the perimeter. This will prevent spillage entering the cupboard under the hotplate.
• DO NOT USE SILICONE WHEN INSTALLING YOUR COOKTOP.
THIS WILL VOID YOUR WARRANTY.
• WHEN THE HOTPLATE IS INSTALLED ABUTTING A SIDE OR REAR WALL, THE WALL MUST
BE OF NON-COMBUSTABLE MATERIAL, e.g. CERAMIC TILES.
The following minimum clearances to combustible materials must be observed:
• Minimum clearance from hotplate edge (Burner) to side wall must be 200mm
• Minimum clearance from the hotplate (burner) edge to rear wall must be 200mm
• Minimum clearance from the hotplate to cupboard above the hob burners must be minimum
of 600mm.
• Range hoods and overhead exhaust fans must be installed according to the manufacturers’
instructions and AS5601, but in no case shall clearance from hob burners be less than
700mm for the range hood and 750mm for the overhead exhaust fan.
• It is recommended that the adjacent kitchen surfaces should be capable of withstanding
temperatures of 100ºC.
• Refer also AS5601 for installation requirements.
The hotplate must be secured to the bench using the supplied brackets to ensure hotplate
does not move.
Cut out dimensions (95GTG example only)
MODEL WIDTH DEPTH
95GTG 827mm 475mm
75GTG 552mm 474mm
64GTG 552mm 474 mm
865
475
510
827

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 12
INSTALLATION – GAS CONNECTION
These Technical Instructions have been prepared for use by Authorised persons.
PLEASE RECORD YOU PLUMBERS DETAILS AT THE BACK OF THIS BOOK – INCORRECT
INSTALLATION OF GAS FITTINGS AND APPLIANCES ARE NOT COVERED UNDER WARRANTY!!!
• This unit must only be installed by an Authorised person e.g. licensed plumber and gasfitter
– FAILURE IN DOING SO WILL RESULT IN ALL WARRANTIES BEING VOIDED.
• This appliance is for use with connections using rigid copper connection or;
• This appliance is suitable for installation with a flexible hose connection. Hose connection
must be to AS1869 – Class B; and be no more than 1.5 metres in length. Hose must be
support independent of any surface which may become hot.
• Gas Inlet fitting is ½” BSP (male) thread.
• Fit the appliance inlet elbow and sealing washer and tighten, attach the regulator supplied
for Natural Gas (if applicable) as close as possible to inlet of the hotplate.
• For LPG appliances, the test point adaptor (supplied) must be fitted. The supply connection
is to be accessible with the appliance installed.
NOTE: It is recommended that an isolating valve
and union be fitted, to enable disconnection for
servicing. These are to be in an accessible location.
Check connections are gas tight with soapy water
or other approved method.
UNDER NO CIRCUMSTANCES ARE YOU TO USE
A NAKED FLAME WHEN CHECKING FOR LEAKS.
Ensure the appliance operating pressure is
adjusted and set according to these instructions
and local authority requirements. When satisfied
that the hotplate is operating correctly, instruct the
customer in its safe operation. Ensure the customer
understands fully by having them operate the
hotplate and all its functions.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 13
INSTALLATION – ELECTRICAL CONNECTION
BEFORE CONNECTING THE PLUG INTO THE POWER SOCKET, FOLLOW THESE INSTRUCTIONS:
• The electrical supply for the upright cooker must be a 240Volt 50 Hz.
• The fuse and electrical wiring of the home / premises must support the load of the
appliance.
• The 3-pin plug, used to connect the electricity, must be easily reached when the hotplate is
in its installed position.
• The hotplate must be earthed. Connect the hotplate to a properly earthed and rated power
socket, as appropriate.
• The flexible cord of the appliance must not be subject to direct heat and must be positioned
after installation of the hotplate so that its temperature does not exceed 75ºC.
IMPORTANT: If a power socket needs to be installed or relocated, the work must be
carried out by a licensed electrician.
INSTALLATION –
GAS CHECKS AND BURNER ADJUSTMENTS
IMPORTANT: Set appliance operating pressure, to that indicated on appliance data plate.
The test point is located on the appliance regulator (or adaptor for LPG).
PRESSURE ADJUSTMENT
•
• Remove the sealing screw from the regulators test point at the rear of the appliance and
place the hose of the Manometer onto it. Turn the gas on to the appliance and light the
Wok Burner and Small Burner at maximum setting. Check the pressure and adjust at the
regulator if necessary to the settings in the table on the last page or on the Data plate.
• For Propane Gas, adjust at the regulator on the gas supply cylinder – Turn regulator
adjusting screw clockwise increase pressure whilst anti-clockwise decrease pressure.
Refit the test point sealing screw when finished. Check installation for correct operation.

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 14
LOW FLAME SETTING
• Check the lowflame setting for each hob burner with the control engaged in the minimum
position. Turnthe control until it engages in the minimum position & remove the control knob.
Insert a screwdriver in the adjusting screw (located next to the gascock flame failure shaft).
• To increase the flame, turn the adjusting screw anti-clockwise.
• To decrease the flame, turn the adjusting screw clockwise. Adjust for a minimum, stable and
clear flame.
ENSURE THAT THE MINIMUM FLAME WILL NOT BE EXTINGUISHED BY AIR DRAUGHTS
IGNITER OPERATION
• Check that the igniter for each burner successfully ignites the gas and that the burner
remains alight.
• If anigniter fails to work or a burner fails to remain alight:
1. first remove the electrical supply plug from the electrical power outlet (GPO),and then check
that all the electrical connections are clean, dry and in place.
2. Also check burner to ensure portsare not blocked or dirty.
3. If the hotplate fails to operate correctly, contact Daniela Appliances Pty Ltd or their
appropriate agent for service.
ANCILLARY SERVICE INFORMATION
• SERVICE TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON!
• DO NOT ATTEMPT ANY REPAIRS YOURSELF.
• DO NOT MODIFY APPLIANCE!
• ALWAYS ENSURE THAT THE GAS AND ELECTRICAL SUPPLY IS DISCONNECTED
BEFORE SERVICINGAPPLIANCE.
It is also recommendedthat this appliance be serviced at 12-month minimum intervalsor
sooner if required. This service is not covered by warranty.
ELECTRICAL EQUIPMENT AND COMPONENTS
ALWAYS ENSURE THAT THE POWER SUPPLY IS DISCONNECTED BEFORE
SERVICING THE APPLIANCE.
• The electrical component is primarily located below the hob surface. Removal of the hob is
straightforward by removing the control knobs, the trivets, the burner caps and burner head
assemblies and skirts.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 15
• Using aflat bladed screwdriver remove the five screws, one in each corner of the hotplates
left and right spillage bowls andone centrally located at the rear of the centre spillage bowl.
• Then lift the hob upwards. Replacement is a reversal of the above procedure.
• Care must be taken to ensure that no damage occurs to the spark ignition leads or the
igniters. The electronic ignitionpack is easily accessible for service or replacement below
the hob centrally at the rear.
GAS CONTROLS AND GAS MANIFOLD
• Removal of the gas manifoldis initially accomplished by removing the control knobs, the
trivets,the burner caps and burner head assemblies and skirts.
• Using aflat bladed screwdriver remove the five screws, one in each corner of the hotplates
left and right spillage bowls andone centrally located at the rear of the centre spillage bowl.
• Care must be taken to ensure that no damage occurs to the spark ignition leads, igniters
or thermocouples, if fitted. Disconnect all ancillary gas piping. Remove the two securing
brackets at the front and also the securing bracket near the gas inlet point to the burner
compartment. The gas manifold may then be extracted.
• Replacement is reversal of the above procedure.
CONVERSION TO ANOTHER GAS TYPE
• If the gas appliance is to be used with another gas type e.g. either Propane Gas or Natural
Gas, it must be convertedby an Authorised Person.
• Contact Daniela Appliances Pty Ltd or their authorised agent for information and parts.
NATURAL GAS PROPANE GAS
Injector
Diameter MJ/h Gas Pressure
Injector
Diameter MJ/h Gas Pressure
Wok Burner 1.70 13 1.0 kPa 0.98 13 2.75 kPa
Large Burner 1.40 10 1.0 kPa 0.90 10.5 2.75 kPa
Medium Burner 1.10 6.5 1.0 kPa 0.70 6.5 2.75 kPa
Small Burner 0.90 4.2 1.0 kPa 0.55 3.7 2.75 kPa
***64 30.2 MJ/h 29.7 MJ/h
***75, ***95 40.2 MJ/h 40.2 MJ/h
The table above shows the appropriate injector sizes for either Natural Gas or LPG (Propane)

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 16
IMPORTANT! The conversion work must be carried out by a registered gas fitter and in
accordance with the current standards.
WARNING: Always isolate the cooktop from the electricity supply before changing the injectors
and/or adjusting the minimum flow of the burners.
MINIMUM FLOW ADJUSTMENT FOR COOKTOP GAS TAPS
IMPORTANT! All work must be carried out by a registered gas fitter and in accordance with the
current standards.
WARNING: Always isolate the cooktop from the electricity and gas supply before changing the
injectors and/or adjusting the minimum flow of the burners.
• Switch the burner on and set the knob at the minimum position.
• Remove the knob from the tap and place a small bladed screwdriver in the centre of the tap shaft.
• Unscrewthe adjusting screw, in order to increase the gas flow or tighten the adjusting screw
to decrease the gas flow.
• The correct adjustment is obtained when the flame has a length of about 3-4mm.
• For ULP gas, the adjusting screw must be tightly screwed in.
• Refit the control knob.
• Make sure that the flame does not go out by quickly turning
from maximum flow to minimum flow. lf it does then remove
the control knob and make further adjustments to the gas flow,
testing it again once the adjustment has been made.
• Repeat thisprocessfor each one of the gas taps.
• When converting from Narural Gas to ULP gas ensure that the NG
regulator is removed and replaced with the Test Point Assembly. A gas regulator suitable for a
supply pressure of 2.75kPa should be at the inlet to the appliance. Replace the old data plate
with one which is suitable for the type of gas for which the appliance has beenregulated.
IMPORTANT! Where this appliance isinstalled in marine craft or in caravans, it shall not be usedas
a space heater.
• Remove the pan-stands,burners and flame spreaders (A).
• Unscrewthe injector (B) and replace it with the stipulated
injector for the new gas supply (see table on page 15).
• Reassemble all the burners carefully; in particular you
shouldmake sure that the flame spreader is correctly
placedon the burner.
IMPORTANT! The minimum flow adjustment process
must be completed before the appliance is next used.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 17
PRACTICAL HINTS FOR USE:
• Do notuse pots which exceedthe
width of the trivets.
(Note: the trivet is the cast iron frame
with fingers that the potssit on).
• Caution: if the pot size exceeds the edge
of the trivet,flames could cause damage to
stainless steel surfaces either side of the hotplate.
• Do notuse pots which are too small for the burner size, they may become unstable
on the trivet.
• Alwaysuse cookware that is appropriate in size for the size of the burner.
• Neveruse pots that are too small or too large. For wok cooking it is recommended that a
domestic size wok, no larger than400mm in diameter be used.
• Note:use a strong flame to bring liquids to the boil, seal meat and generally for foodwhich
must be cooked rapidly – i.e. whenusing a wok.
• Note:use a low flame for sauces or stews.
• Do not cook food over too strong a heat. Boil fast does not cook any faster but violently stirs
up the food so that it loses its flavour.
• Do not use aftermarket lids or covers with this appliance.
OPERATING – THE GAS HOB
• When the burner is a light, adjust the flame to suit the cooking requirements.
• If the burner still fails to ignite, a match or lighting device can be used, but care must be taken.
• If the problempersists, contact Daniela Appliances Pty Ltd or their authorised service agent
for a service.
• DO NOT TOUCH HOT SURFACES, ALLOW HOB TO COOL BEFORE WIPING SPILLAGE.
• Keep the gas igniters clean and dry.
LIGHTING BURNERS
• Simply press the knob in and turn,
anti-clockwise to maximum.
• Check that the gas has been lit.
•
then try again. Select the right size burner for the required cooking.

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 18
OPERATING AND CLEANING
• DO NOT TOUCH HOT SURFACE, ALLOW HOTPLATE TO COOL BEFORE CLEANING.
• Alwayswipe spills up when they occur.
• Do not leave spills to dry onto the surface of the hob.
HOB BURNER CAPS
• The hob burner caps simply sit on the burners. Just remove them and clean them with a
moist, slightly soapy sponge.
• Do notput themin water immediately after use. Thermal shock could cause the enamel to
crack, thus causing them to discolour or rust.
• Do not soak or submerge them in water, as this will most definitely cause the cast iron to rust.
Never use abrasives, caustic oven cleaners, steam cleaners or harsh chemical cleaning agents
as they are not recommended and couldpotentially scratch, dull and even damage the surface.
Never use abrasives, caustic oven cleaners, harsh chemicals, scouring pads,steam cleaners or
sharp objects. This will cause irreparable damage to the enamel.
•
clean, dry cloth.The enamel could dull if cleaned while it is still hot.
• Do not soak or submerge them in water, as this will most definitely cause the cast iron to rust.
STAINLESS STEEL AND CHROMED PARTS
• Use commercial products designed for cleaning stainless steel and chromed steel,and
followthe manufacturer’s instructions.
• Care should be taken when cleaning around the graphics.
Never use abrasives, caustic oven cleaners, harsh chemicals, steam cleaners, scouring pads or
sharp objects.

P I 029604 1226 E [e-mail]| danielaappliances.com.au
PA G E 19
TROUBLESHOOTING
• USERS ARE NOT ALLOWED TO PERFORM ANY MAINTENANCE
OPERATIONS ON ANY PARTS OF THIS APPLIANCE.
• MAINTENANCE MUST BE CARRIED OUT EXCLUSIVELY BY AUTHORIZED
TECHNICAL SERVICE PERSONNEL.
To access burners, injectors, valves etc; disconnect gas and power supply from appliance.
Ensure appliance is cool before removing trivets, burners etc.
When you need to access under hob, remove screws which hold the hob in position, located
under each burner. Lift hob to access valves and electrical system.
To re-assemble, carry out work in reverse order, and test operation of appliance before leaving.
TROUBLE POSSIBLE CAUSE
SOLUTION
FOR THE USER FOR THE TECHNICAL
SUPPORT SERVICE
Burner won't light.
Gas and electrical supply
not working.
Check the gas supply
is turned on. Also
ensure electrical
supply is operational.
Test gas pressure
and electrical supply
is correct. Turn on if
necessary.
Pressure drop in gas pipe
Check appliance inlet
supply, pipe sizes,
contact the gas utility
company.
The ignition plug is not
securely fixed, or the
connection with the
cable is wrong.
Check the
connection.
Gas valve damaged. Replace it.
After releasing the
knob, the flame
goes out.
The thermocouple is not
burner flame.
Clean and reapet the
ignition procedure.
Clean burner
assembly.
Thermocouple faulty. Replace the
thermocouple.
Gas valve faulty. Replace it.

P I02 9604 1226 E I [e-mail] W| danielaappliances.com.au
PA GE 20
TROUBLE POSSIBLE CAUSE
SOLUTION
FOR THE USER FOR THE TECHNICAL
SUPPORT SERVICE
After releasing the
knob, the flame
goes out.
Burner flame uneven.
Clean burner by
washing in warm soapy
water, dry and locate
burner correctly.
Check injector for
dirt/spillage. Clean
or replace burner if
necessary.
Pot supports not
correctly positioned.
Pot supports are
designed to go in one
location. Ensure pot
support is correctly
located over burner.
Gas smell.
Gas burner turned on
but not ignited.
wait 5 minutes. Ventilate
area. Attempt to relight
burner and ensure flame
stays lit.
Use approved
methods of checking
and locating gas
leaks. Repair as
required.
and can smell gas appliance isolating valve
and contact gasfitter.
Replace it.
Burner flame uneven.
Clean burner by
washing in warm soapy
water, dry and locate
burner correctly.
Check injector for
dirt/spillage. Clean
or replace burner if
necessary.
Pot supports not
correctly positioned.
Pot supports are
designed to go in one
location. Ensure pot
support is correctly
located over burner.