Dante DLZ6830 User manual

DLZ6830
Explosion Proof Heavy Duty
Pan/Tilt System
Installation and Operations Manual
Model Number: DLZ6830
Description: Explosion Proo Pan/Tilt System

TA LE OF CONTENTS DLZ6830 page
1. Installation 3
1.1 Foreword 3
1.2 Sa eguards 3
1.3 Description & Features 3
1.4 Wall Mount Installation 5
1.5 Technical Parameters 6
1.5.1 Structure parameters 6
1.5.1.1 Wall Mount Bracket 7
1.5.1.2 Pole Mount Bracket 8
1.5.1.3 IR Lamp Support Bracket 9
1.5.2 Rotating parameters 10
1.5.3 Electrical parameters 10
2. Operation 10
2.1 Basic Description 10
Appendix A Troubleshooting 11
A.1 PTZ Controls 11

1. INSTALLATION MANUAL
1.1 FOREWORD
This manual introduces the unction, installation and operation o the ex-proo
Pan/Tilt in details. Please thoroughly amiliarize yoursel with the in ormation in this
manual prior to installation.
This series pan/tilt is specially designed or lammable，explosive atmosphere,
homeland security and customs etc. It has many eatures: reliable, stable, airproo ,
waterproo , acid water proo , able to withstand high temperature, aging, strong wind and
so on. It adapt to the ollowing harsh conditions, such as high wind power, wide
changing temperature conditions, high electromagnetism and lightning and continuous
operating conditions.
This series Pan/Tilt can match with all kinds o ex-proo camera. It can turn le t, right,
up and down according to the orders o the decoder. This manual will not explain the
operation o other devices i connecting with system, please read the manual o the
inter acing product or device.
1.2 SAFEGUARD AND WARNINGS
Prior to installation and use o this product, the ollowing WARNING should be
observed. This product may be only used in speci ied range in order to avoid any
damage or danger.
Installation and servicing should only be done by quali ied service personnel;
It may not be used in temperature range, humidity and power supply outside
the speci ications.
Only use replacement parts recommended by actory.
No use o strong or corrosive cleanser to avoiding scu ing.
Never open the Pan/Tilt on a using occasion to avoid the danger o the
explosion.
The installation bracket should be capable o supporting our times the total
weight o the integrated camera.
Please thoroughly read this manual prior to installation and operation.

1.3 DESCRIPTION AND FEATURES：
：：
：
1.3.1 Description
DLZ6830 Series are Explosion Proo Pan Tilt Positioning Systems that
represent state-o -the art, rugged and corrosion resistant surveillance
technology equipment. Units eature Stainless Steel 316 construction or
installation o Ex proo camera housing assembly, optional Ex proo IR Lamp
(as shown in photo) and is controlled by Ex proo DLZ6500 series
Receiver/Driver via RS-422/RS-485. With IP67 outdoor rating and 24VAC and
85-265VAC input voltages, the DLZ6830 series Explosion proo Pan Tilt
Camera Positioning Systems are designed to meet the most demanding
commercial and hazardous industrial video surveillance installations.
1.3.2 Features
The Pan/tilt is made o high strength 316L stainless steel, waterproo , and able to
withstand high temperature, aging, and corrosion
Wall mounting installation
Gear speed reducer, stable operation and accurate orientation
Pan rotation: 0 ~ 3600 rotation.
Tilt rotation: -900 ~ +900 rotation
Manual control speed or pan: 60/sec.
Manual control speed or tilt: 60/sec.
Maximum load 30Kg
Complies with Exd II CT6(H2) and IP67 standards
Working temperature: -40 °C ~ +50 °C
Indoor or outdoor or all weather use
Power Consumption 135W

1.4 WALL MOUNT INSTALLATION
The wall installation camera contains ollowing parts. Inspect each package to make
sure all parts are present.
Ex-proo pan/tilt wall bracket
Steps of wall installation
STEP 1 Install the Φ10mm screws on the wall (re er to the ollowing picture)
STEP 2 Install the bracket directly on the wall.
Pan/tilt 1 pc
wall bracket 1 pc
connecting cables 1 pc
pedestal water joint 1 pc
manual 1 set
Glove 1 pair
Fixed screw Φ6X20mm ( or Pan/Tilt)) 4 sets
Φ10X40mm bolts 12 sets

STEP 3 Use the our Φ6×20 screws ix the Pan/Tilt on the wall bracket.
STEP 4 connect the cables. Connect the cable according to the ollowing pinout
diagram:
STEP 5 Turn on the power to check operation
1.5 TECHNICAL PARAMETERS
1.5.1 Structure parameters
Ex-proo pan/tilt 316L stainless steel
Bear weight mode side
standard bear weight 30Kg
installation wall mount,
bracket requirement 4 times o the pan tilt’s weight
operating temperature -40ºC ~ 50ºC
Dimension as the ollowing dimension picture

1.5.1.1 Wall Mount racket
For wall mount installations, the steel wall bracket DLZ1871 is used or support o
DLZ6830 Pan/Tilt System as per diagram below:

1.5.1.2 Pole Mount racket
For pole mount installations, the steel wall bracket DLZ1877 is used or support o
DLZ6830 Pan/Tilt System as per diagram below:
DLZ6830 Pole Mount Bracket
DLZ6560 Receiver Driver
vi ew
vi ew

1.5.1.3 IR Lamp racket Diagram
When the IR Lamp DLZ69000 Series is required as an option to the integrated Pan/Tilt
and Housing camera system, there is an additional steel wall bracket included. This
bracket supports the IR Lamp as per diagram below.

1.5.2 Rotating parameters
Pan rotation 0~3600 rotation
Tilt rotation -90~ +900 rotation
Manual control speed
Pan 60/sec manual operation
Tilt 60/sec manual operation
1.5.3 Electrical parameters
Input voltage 12VDC, 24VAC, 230VAC, 50/60Hz
Input power 50VA
Cable requirement: RVV5X0.5mm2
2. OPERATION
2.1 ASIC DESCRIPTION
A ter connecting wires as per instructions in previous section and turning on power, the
pan/tilt will work according to the order o the decoder.
Upon success ul con iguration, user may operate the Pan/tilt as the ollowing way:
OPERATION PROCEDURE
Pan/Tilt 1. To move via control keyboard, Pan/Tilt will rotate to the
operation direction i the joystick leans to one direction o
up/down/le t/right. The Pan/Tilt will move to the operation
direction in 60/sec. The Pan/Tilt will stop when the joystick
returns to the center.

Appendix A TROU LESHOOTING
1. PTZ Controls - use with DLZ6560 Series Receiver/Driver
Problem: the Pan/Tilt may not be controlled by keyboard or other control equipment?
→First check i control line RS-485 is well connected to designed position with right
direction. Then check the control equipment and P/T control protocol, baud rate
and address. I it still may not be controlled, use elimination to check whether the
control equipments or Pan/Tilt has a problem.
Problem: other controls are normal except it may not rotate in one direction.
→First check i any mechanical troubles without powering unit. I it may run well,
check i the belt broke or loose. I yes, it is caused by the control receiver/driver
(decoder) board has a problem.
Problem: the Pan/Tilt may be controlled normally in the morning and evening, but it
may not be controlled in summer mid-day hours.
→High temperature may cause lower down o control line anti-jamming or change
to control equipment and CMOS chips parameters to create problems. Check i the
temperature is over than the speci ied limit and i an is unctioning.