Davaon Pro Switch 1 in 1 Ratchet Anvil Loppers Installation guide

Note: Always take care when using tools with sharp blades. These are extremely sharp.
Thank you for purchasing our Davaon Pro Switch Ratchet Anvil Loppers. We hope you en-
joy using it.
Support—Should you have any queries you can contact us 24/7 by sending a message via
your marketplace account or via our [e-mail] and we aim to answer any
questions within 2 hours of receiving your message.
User & Care Instructions
Reminder Of Some Key Features
Pro Switch 1 in 1 Ratchet Anvil Loppers
Page 1

Page 2
Note: Always take care when using tools with sharp blades. These are extremely sharp.
User & Care Instructions
Pro Switch 1 in 1 Ratchet Anvil Loppers
General Care Instructions
1) CLEANING
 Clean carefully after use using a damp soft cloth to clean handles and blades
ensuring you clean away from the sharp edges (NOT INTO THEM). Mind your
fingers
 Then dry using another cloth if required
2) Ensure they are closed after use - See below for instructions
3) Oil cutting mechanism and blade from time to time
4) STORE IN A SECURE, SAFE PLACE
5) If the blade gets stuck in a branch, open the handles, gently move the loppers
so the blade moves up and down. DO NOT Twist the loppers/blade to release.
6) Check bolts/nuts for ghtness from me to me
Instructions
Page 2 - General Care
Page 3 - Opening and Closing
Page 4 - Selecting Ratchet or Single Cutting Mode
Page 5 - Using Ratchet Mode
Page 6 - Using Single Cut Mode, Warranty and other
Page 7 - Product Range
Note:
These are capable of cutting up to 6cm branches. The handles will open wide for
6cm cuts.

Page 3
User & Care Instructions
Opening
1) Remove plastic sleeve
2) Release lock latch by squeezing the
handles together a little and moving
the lock downwards towards the
handles (NOT upwards towards cut-
ting mechanism)
3) The lock latch can be removed if
required
4) NOTE: The latch is not designed to
be a secure lock.
Pro Switch 1 in 1 Ratchet Anvil Loppers
Closing Instructions
Closing In Ratchet Mode (Button in ON position)
1) Open and close handles (as if you were cutting something) until blade is closed.
2) This allows the ratchet mechanism to engage and keep the loppers closed
3) Put the plastic cover over the blades and move latch in to place
4) Store in a dry, safe place
Closing In Single Cut Mode (Button in Off position
1) Close handles
2) Put the plastic cover over the blades and move latch in to place
3) Store in a dry, safe place

Page 4
User & Care Instructions
Pro Switch 1 in 1 Ratchet Anvil Loppers
2 Cung Modes In 1 Lopper
1)Close Handles
2)Press and Move the buon
ON for Ratchet Mode or
OFF for One Cut Mode
Buon ON = RATCHET MODE
✓Cuts Up To 60mm
✓In Several Pressure Increasing Steps
✓Reduces Eort Required
✓Increase User Power To Up 50%
Buon O = ONE CUT MODE
✓Cuts Up To 30mm
✓In One Cut
✓Compound Cung Acon Helps Reduce
Eort Required
✓Increases User Power

Page 5
User & Care Instructions
Using In ’Ratchet’ mode - Max 60mm Cut
Using a lopper with a Ratchet Mechanism is very simple and it adds power to your hands.
If you are used to using a non ratchet lopper then it may take just a few cuts to get used
to the mechanism. But there is nothing to worry about as this is normal.
1) Move red button to On and
then open the loppers.
2) Squeeze handles fully together
to start cutting the branch. When
the handles are fully closed, Open
them again until you hear the
Ratchet mechanism click. Then
stop opening them
Pro Switch 1 in 1 Ratchet Anvil Loppers
Ratchet Mode Closing Instructions
1) Open and close handles (as if you were cutting something) until blade is closed.
2) This allows the ratchet mechanism to engage and keep the loppers closed
3) Put the plastic cover over the blades
4) Store in a dry, safe place
3) Now the 1st stage of the ratchet
mechanism is engaged.
4) You can now close the handles, fully again
and cut.
5) Continue repeating stage 2 and 3 until the
branch is fully cut

Page 6
User & Care Instructions
Using In ’Single One Cut ’ mode - Max 30mm Cut
Single, one cut, mode is great for branches up to 30mm when ratchet mode is not required.
The advanced compound cutting action is used here, when you move button to ‘Off’
1) With the loppers closed, move red button to Off position and then open the loppers.
2) The blades will be set to open for max. 3cm diameter branches
3) The cutting mechanism will be set to advanced compound cutting action
4) Cut the branch in one squeeze of the handles
Pro Switch 1 in 1 Ratchet Anvil Loppers
Warranty
1) We offer a 5 year guarantee against any manufacturing defects
2) Contact Davaon customer care at [e-mail] with your original order
number, description of fault and photos. We aim to respond in less than 2 hrs
3) We are fair with our guarantee and will always try to help as much as we can
Some of what is not covered by the guarantee?
1) Misuse or accidental damage
2) Damage caused by cutting branches thicker than recommended or twisting blade/
handle during use
3) General wear and tear
4) Guarantee will be void if the loppers show signs of not being looked after and
maintained correctly

Page 7
Davaon Garden Tools Range
User & Care Instructions
Why not check out the rest of our Davaon Garden Tools Range
Pro Switch 1 in 1 Ratchet Anvil Loppers