Daytona 37582 User manual

INSTRUCTION MANUAL
1. Read all instructions before use.
2. After installation, check to see if all the parts are correctly
installed, and see if all the screws are torqued properly.
3. Do not adjust the damper while riding.
4. Periodical inspection of the installed parts is required every
500km (300mile). If anything unusual may be found while
riding, pull over at a safe place to check.
Thank you for purchasing DAYTONA STEERING DAMPER KIT.
Product Features
- Stabilizes steering especially at high speed.
- Prevents the front forks from being twisted during high speed
cornering.
- Bolt-on mount. The kit inclides application specific brackets and
all hardware for easy mounting.
Install
37582 / 80674 : 20210915
STEERING DAMPER KIT
for H-D FXST (’00-’07)
PAGE 1 of 2
Before installing, turn the adjustable knob
counter-clockwise to the end.
Fig.1
Softer
*Install stabilizer on the right side of motorcycle.
Install FORK BRACKET
1. Attach fork bracket(#2) on the right front fork tube.
Install FRAME BRACKET
Install DAMPER BODY
3. Install the DAMPER BODY(#1)
with the M8X30 BUTTON HEAD SCREW.
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
#2. FORK BRACKET SET
LOWER TRIPLE CRAMP
L-FORK TUBE
#2. FORK BRACKET
LOWER TRIPLE CRAMP
25-30 degrees
M6X20 CAP SCREW
M6X20 CAP SCREW
#3. FRAME BRACKET SET
FRAME DOUN TUBE
#4. M8X25 BUTTON HEAD SCREW
#1. DAMPER BODY
#2. FORK BRACKET
Apply thread locking fluid
2. Attach frame bracket(#3)
on the right side frame down tube.
FWD.
FWD.
FWD.
FWD.
FWD.

37582 / 80674 : 20210915
8. M8 FLANGE NUT
[ 22N-m / 16lbf-ft ]
Apply thread locking fluid
7. M8x30
BUTTON HEAD SCREW
6. ROD END
3. FRAME BRACKET SET
[ 22N-m / 16lbf-ft ]
9. M8 NUT
[ 22N-m / 16lbf-ft ]
5. BODY CLAMP
2. FRONT FORK BRACKET SET
1. DAMPER BODY
PAGE 2 of 2
[ 10N-m / 7lbf-ft ]
**Each motorcycle has different tolerance. Therefore, different
combination of the fork bracket angle and the body clamp may
be necessary within small range instead of indicated positions
by the diagrams.
Adjust the bracket and the body clamp to the set stabilizer on
the best position if necessery.
Turn the handlebar and check the steering to see if it reaches
both right and left steering stoppers completely.
Make sure the stabilizer does not hit or rub against the fork
tube, frame, engine or the front brake line under the steering
stem.
Tighten all bolts and nuts after to make sure the installation
done right.
Then adjust to your desired level of dampening.
[ 10N-m / 7lbf-ft ]
4. M8x25
BUTTON HEAD SCREW
HIGH PERFORMANCE PARTS AND ACCESSORIES FOR ALL MOTORCYCLE LOVERS.
#5. BODY CLAMP
#1. DAMPER BODY
#3. FRAME CLAMP #7.M8X30 BUTTON HEAD SCREW
#6. ROD END
#8. M8 FLANGE NUT
#9. M8 NUT
Install BODY CLAMP
Adjust the DAMPER
BODY(#1) position. Make
sure DAMPER BODY(#1)
doesn’t hit any part of
motorcycle when turning
the handlebar to the leftmost
and rightmost position.
(see Fig.10)
FWD.
105-115mm
(4.14”-4.53”)
Softer Harder
How to adjust the damping force
Turn the adjustable knob
clockwise → Harder
Turn the adjustable knob
counter-clockwise → Softer
DO NOT over tighten the damper body clamp. The stabilizer
body can be damaged.