De La Espada LIGHT EXTENDING TABLE BY MATTHEW HILTON User manual

0
1
M
A
T
T
H
E
W
H
I
L
T
O
N
PARTS
1x Tabletop
2x Extension leaves
2x Leg frames
1x Cross beam
Hardware:
(4x) Universal connector (4x) Metal dowel
(8x) M8x40 bolts (3x) M8x60 bolts
(11x) washers
YOU WILL NEED
-6mm Allen Key
-The help of a friend
NOTES
NOTE 1: Be certain that all assembly is carried out on a at
and stable surface. This will ensure a good nal result.
Reverse the steps to disassemble the piece.
NOTE 2: Your furniture arrives packed in numerous layers that
protect it during transport. It is important that you remove
the packaging carefully to avoid damaging your furniture. Refer
to our information sheet “Unpacking Your Furniture” for further
details.
NOTE 3: Great care is required when assembling our products .
Use blankets to soften the assembly surface - hard surfaces
such as wood or stone ooring may damage the furniture if in
direct contact.
NOTE 4: We advise that assembly and disassembly of De La Espada
furniture is undertaken by a minimum of 2 people.
NOTE 5: When screwing in bolts, tighten well, but be sure
NOT TO OVERTIGHTEN. This can cause the thread to strip thus
resulting in A poor connection.
ASSEMBLY INSTRUCTIONS
LIGHT EXTENDING TABLE BY MATTHEW HILTON
[e-mail] M
DELAESPADA.COM

0
2
M
A
T
T
H
E
W
H
I
L
T
O
N
b) Match the number on each leg frame with the number marking
on the tabletop and crossbeam.
c) Attach one leg frame to the cross beam by inserting the
metal dowels on the leg into the universal connectors on the
crossbeam. Tighten with an Allen Key.
NOTE: The recessed holes for the M8 bolts on the cross beam
should face downwards.
Repeat the steps to connect the second leg frame.
ASSEMBLY INSTRUCTIONS CONTINUED
LIGHT EXTENDING TABLE
NOTE 6: While you work, be sure all connections are ush with
no gaps.
NOTE 7: After assembly, ensure that the table is resting on a
level surface
INSTRUCTIONS
1. ATTACH LEGS TO THE CROSS BEAM
a) Insert metal dowels into the holes on the side of the leg
frames by screwing them in a clockwise direction until tight.
detail
[e-mail] M DELAESPADA.COM

0
3
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
LIGHT EXTENDING TABLE
2) ATTACH LEGS AND CROSS BEAM TO TABLETOP
Place the tabletop upside down a clean, soft surface such as
blanket or carpet on the oor.
Match the number on the leg frames with the number markings on
the tabletop.
Align the holes on the cross beam and leg frames with the holes
on the tabletop. Insert washers and the M8 bolts (3 long into
the cross beam, 8 short into the legs)and tighten with an Allen
key.
d) Notice on the underside of the tabletop there are two re-
cessed holes. In these holes you will nd a locking mechanism
which allows you to release the tabletop when desired, allowing
it to be opened.
Important: unlock mechanism only when the table is in the up-
right position.
detail
[e-mail] M DELAESPADA.COM

0
4
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
LIGHT EXTENDING TABLE
3) TURN THE TABLE INTO AN UPRIGHT POSITION
With the help of a friend, carefully turn the table over into
an upright position, taking care not to place any weight/force
on the table legs while turning.
Once the table is in an upright position, you can release the
locking mechanism if desired.
4) EXTENDING THE TABLE
a) To extend the table, rst unlock both mechanisms located on
the underside of the table. With the help of a friend, careful-
ly and simultaneously pull both panels from the outer corners
as indicated.
Please take care when opening the tabletops, pulling equally on
each side so that the system is not put under undue stress.
[e-mail] M DELAESPADA.COM

0
5
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
LIGHT EXTENDING TABLE
b) With the table fully open, place one or both extension
leaves (as desired) into position, carefully connecting all
guiding dowels with their corresponding holes.
c) With the extension leaves in place, join the panels by push-
ing the outer corners of the tabletops simultaneously, with the
help of a friend. Next, lock the mechanism on both sides. The
table is now extended and ready for use.
Note: NEVER carry, lift or move the table by the upper leaves
as this may damage the table. Always move the table only by the
angled subframe that sits beneath the top leaves. Remove both
extension leaves, close and lock the tabletop before moving.
guiding dowels
[e-mail] M DELAESPADA.COM

0
6
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
LIGHT EXTENDING TABLE
STORING THE EXTENSION LEAVES
a) When desired, the extension leaves can be stored within the
table as follows. One leaf should be placed face down into the
fabric lined compartment. The other leaf should be placed face
up on top of the rst leaf, so the felt pads on the bottom of
the two leaves meet.
b)Join the panels by pushing the outer corners of the tabletop
simultaneously with help from a friend. Next, lock the mecha-
nism on both sides.
The table is now closed and ready to use.
[e-mail] M DELAESPADA.COM