De La Espada BRETTON User manual

0
1
M
A
T
T
H
E
W
H
I
L
T
O
N
PARTS
HARDWARE
(4x) Universal connector (4x) M8x40 Metal dowel
(12x) M6x20 bolts (10x) M6x45 bolts
(26x) M5 bolts (26x) M5 washers
YOU WILL NEED
-8mm socket/ratchet set OR cordless drill with the appropriate
attachment
-Phillips head screwdriver
-6mm and 5mm Allen Key
-The help of a friend
NOTES
NOTE 1: Be certain that all assembly is carried out on a at
and stable surface. This will ensure a good nal result.
Reverse the steps to disassemble the piece.
NOTE 2: Your furniture arrives packed in numerous layers that
protect it during transport. It is important that you remove
the packaging carefully to avoid damaging your furniture. Refer
to our information sheet “Unpacking Your Furniture” for further
details.
NOTE 3: Great care is required when assembling our products .
Use blankets to soften the assembly surface - hard surfaces
such as wood or stone ooring may damage the furniture if in
direct contact.
NOTE 4: We advise that assembly and disassembly of De La Espada
furniture is undertaken by a minimum of 2 people.
ASSEMBLY INSTRUCTIONS
BRETTON BED BY MATTHEW HILTON
[e-mail] M
DELAESPADA.COM
1x Headboard
1x Central beam
2x Side beams
13x Timber slats
(14 for Cal King)
4x Metal feet
1x Footbeam
1x Headbeam

0
2
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
BRETTON BED
1. ATTACH CENTRAL BEAM TO HEADBEAM AND FOOTBEAM
a) Unpack components and lay them face down on the oor, so
they are in the correct orientation. Check for number markings.
b) Place cutout of central beam onto the cutout on the head-
beam, by slotting the wooden dowels into the corresponding
holes.
[e-mail] M DELAESPADA.COM
NOTE 5: When screwing in bolts, tighten well, but be sure
NOT TO OVERTIGHTEN. This can cause the thread to strip thus
resulting in a poor connection.
NOTE 6: All mating parts are numbered so they correspond to
the appropriate part around the frame of the bed. you will
ensure the best possible t if all parts are mated with the
corresponding numbered parts. While you work, be sure all
connections are ush with no gaps.
INSTRUCTIONS
c) Place cutout of central beam onto the cutout on the foot-
beam, by slotting the wooden dowels into the corresponding
holes.

0
3
M
A
T
T
H
E
W
H
I
L
T
O
N
2. ATTACH SIDEBEAMS
a) Lay the sidebeams face down on the oor, so they are in the
correct orientation. Check for number markings.
ASSEMBLY INSTRUCTIONS CONTINUED
BRETTON BED
[e-mail] M DELAESPADA.COM
b) At each corner, place a Universal Connector in the rebate in
the headbeam and footbeam, and insert a metal dowel into each
end of each sidebeam. Guide the metal dowels into the Universal
Connectors and tighten rmly with an Allen Key.

0
4
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
BRETTON BED
3. ATTACH METAL FEET
a) Place a metal foot into the recess in each corner and secure
with three M6x20 bolts, tightened with an Allen Key.
[e-mail] M DELAESPADA.COM
b) The frame should now look like this.

0
5
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
BRETTON BED
c) With the help of a friend, carefully turn over the frame so
it is in its natural upright position.
[e-mail] M DELAESPADA.COM
4. SECURE CENTRAL BEAM
a) Secure the central beam by inserting 2x M6x45 bolts through
the headbeam and footbeam and into the central beam. Tighten
with an Allen Key.

0
6
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
BRETTON BED
5. ATTACH THE TIMBER SLATS TO THE PLATFORM BASE
a) Space out the bed slats so they are aligned with the
corresponding holes on the timber lip on the inner face of
the side beams. The underside of the each slat has a threaded
sleeve xed inside. If the sleeve drops out, there are spares
you can use. The top of each slat has a recess for the washer.
b) Place a washer in the recess of each slat and insert an M5
bolt through the slat and into the sidebeam. Using a cordless
drill or socket set, tighten the bolts. Tighten the slats well,
so they are not wobbly, but be very careful not to overtighten.
[e-mail] M DELAESPADA.COM

c) The platform base should now look like this.
0
7
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
BRETTON BED
6. ATTACH THE HEADBOARD
a) Place the headboard onto the platform base at the headbeam
end, being sure to align the pre-drilled holes.
b) From below, insert 6x M6x45 bolts through the platform base
and into the headboard, tightening with an Allen Key.
[e-mail] M DELAESPADA.COM

c) Assembly is now complete and the bed is ready to receive a
mattress. 0
8
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
BRETTON BED
[e-mail] M DELAESPADA.COM