De La Espada JASON MILLER 051 ELLIOTJASON MILLER 056... User manual

0
1
J
A
S
O
N
M
I
L
L
E
R
PARTS
1x Tabletop
2x Leg frames
2x Cross beams
Hardware:
(4x) Universal connector (4x) M8x40 Metal dowel
(18x) M6x30 Screws (18x) M7.5 washers
YOU WILL NEED
-5mm Allen Key
-6mm Allen Key
-The help of a friend
NOTES
NOTE 1: Be certain that all assembly is carried out on a at
and stable surface. This will ensure a good nal result.
Reverse the steps to disassemble the piece.
NOTE 2: Your furniture arrives packed in numerous layers that
protect it during transport. It is important that you remove
the packaging carefully to avoid damaging your furniture. Refer
to our information sheet “Unpacking Your Furniture” for further
details.
NOTE 3: Great care is required when assembling our products.
Use blankets to soften the assembly surface - hard surfaces
such as wood or stone ooring may damage the furniture if in
direct contact.
NOTE 4: We advise that assembly and disassembly of De La Espada
furniture is undertaken by a minimum of 2 people.
NOTE 5: When screwing in bolts, tighten well, but be sure
NOT TO OVERTIGHTEN. This can cause the thread to strip thus
resulting in a poor connection.
NOTE 6: While you work, be sure all connections are ush with
no gaps.
NOTE 7: After assembly, ensure that the table is resting on a
level surface.
ASSEMBLY INSTRUCTIONS
051/056 ELLIOT DINING TABLE BY JASON MILLER
[e-mail] M
DELAESPADA.COM

0
2
J
A
S
O
N
M
I
L
L
E
R
ASSEMBLY INSTRUCTIONS CONTINUED
051/056 ELLIOT DINING TABLE
INSTRUCTIONS
1) ATTACH CROSS BEAMS TO LEG FRAMES
a) Place the leg frames face down on a clean, soft surface on
the oor.
b) Screw the metal dowels into the pre-drilled holes in each
leg frame.
[e-mail] M DELAESPADA.COM
c) Insert the Universal Connectors into the rebates at either
end of each cross beam.
d) While pushing the cross beams toward the leg frames, guide
the metal dowels into the Universal Connectors to connect the
parts.

0
3
J
A
S
O
N
M
I
L
L
E
R
ASSEMBLY INSTRUCTIONS CONTINUED
051/056 ELLIOT DINING TABLE
[e-mail] M DELAESPADA.COM
f) The assembly should now look like this.
e) Tighten the connections rmly with an Allen Key.

0
4
J
A
S
O
N
M
I
L
L
E
R
ASSEMBLY INSTRUCTIONS CONTINUED
051/056 ELLIOT DINING TABLE
[e-mail] M DELAESPADA.COM
2) ATTACH LEG ASSEMBLY TO TABLETOP
a) Place the tabletop face down on a clean, soft surface on the
oor.
b) Place the leg assembly onto the underside of the tabletop,
aligning the pre-drilled holes.

0
5
J
A
S
O
N
M
I
L
L
E
R
ASSEMBLY INSTRUCTIONS CONTINUED
051/056 ELLIOT DINING TABLE
[e-mail] M DELAESPADA.COM
c) Into each of the pre-drilled holes, insert a washer followed
by an M6x30 screw. Tighten the connections rmly with an Allen
Key.

0
6
J
A
S
O
N
M
I
L
L
E
R
ASSEMBLY INSTRUCTIONS CONTINUED
051/056 ELLIOT DINING TABLE
[e-mail] M DELAESPADA.COM
3) TURN THE TABLE INTO AN UPRIGHT POSITION
a) With the help of a friend, carefully turn the table over
into an upright position, taking care not to place any weight/
force on the table legs while turning.
b) The assembly is now complete and the table is ready for use.