De La Espada McQueen User manual

0
1
M
A
T
T
H
E
W
H
I
L
T
O
N
PARTS
HARDWARE
12x M8x20 bolts
YOU WILL NEED
5mm heavy duty Allen Key
The help of a friend
NOTES
NOTE 1: Be certain that all assembly is carried out on a at
and stable surface. This will ensure a good nal result.
Reverse the steps to disassemble the piece.
NOTE 2: Your furniture arrives packed in numerous layers that
protect it during transport. It is important that you remove
the packaging carefully to avoid damaging your furniture. Refer
to our information sheet “Unpacking Your Furniture” for further
details.
NOTE 3: Great care is required when assembling our products .
Use blankets to soften the assembly surface - hard surfaces
such as wood or stone ooring may damage the furniture if in
direct contact.
NOTE 4: We advise that assembly and disassembly of De La Espada
furniture is undertaken by a minimum of 2 people.
NOTE 5: When screwing in bolts, tighten well, but be sure
NOT TO OVERTIGHTEN. This can cause the thread to strip thus
resulting in A poor connection.
NOTE 6: While you work, be sure all connections are ush with
no gaps.
ASSEMBLY INSTRUCTIONS
MCQUEEN CHESTS BY MATTHEW HILTON
These instructions apply to all McQueen chests, with the
exception of McQueen Bedside Chest which is shipped fully
assembled.
SALES@DELAESPAD A.C O M
DELAESPADA.COM
1x Chest body
4x Legs
Drawers

0
2
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
MCQUEEN CHESTS
1) ATTACH FEET
a)Place the chest so its back is against the oor.
b)Locate the pre-drilled holes on the underside of the chest
c)Place one of the feet against the bottom of the chest, align-
ing the holes in each component. Insert an M8x20 bolt into each
hole and tighten rmly with a 5mm Allen Key. Be careful not to
overtighten. Repeat for each foot until complete.
2) TURN THE CHEST INTO AN UPRIGHT POSITON
a) With the help of a friend, turn the chest so it is in a nat-
ural upright position. Be careful to avoid allowing the chest
to rest on one or two legs while turning as this may damage the
connection.
3) INSERT THE DRAWERS
NOTE: You will ensure the best t by making sure all drawers
are placed in the correct position within the cabinet. Each
drawer has a number on it’s back that corresponds to the number
on the internal back panel of the cabinet where it should be
placed.
a) To install each drawer, locate the orange release clips on
the base of the drawer, and pull them toward the front of the
drawer while inserting the drawer into the cabinet. Once the
drawer is halfway in, release your hands from the clips, and
push the drawer closed.
SALES@DELAESPAD A.C O M DELAESPADA.COM

0
3
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
MCQUEEN CHESTS
4)ADJUST DRAWERS AS REQUIRED
a)Check that the gaps between the drawers are even. If re-
quired, adjust them as follows. Pull out the drawer just far
enough to access the small grey plastic locking clips on the
rails underneath. These clips are located on the far left and
far right just near the drawer front. You can move this locking
clip forward or backward until you achieve the desired spacing
between the drawers. Close the drawer after each adjustment to
check the spacing. In most cases, you will achieve best results
by leaving the clip centred.
b) Repeat the above procedure on as many drawers as necessary,
until the desired result is achieved.
5) The assembly is now complete and the chest is ready for use.
SALES@DELAESPAD A.C O M DELAESPADA.COM