De La Espada 395Q/V OVERTON TABLE User manual

0
1
M
A
T
T
H
E
W
H
I
L
T
O
N
NOTE: These instructions are relevant for the Overton Table
in 400 or 450 cm lengths (157 1/2 or 177 1/8 ”). The hardware
quantities may vary according to size.
PARTS
2x Tabletop halves
2x leg frames
1x cross bar
HARDWARE
(6x) Universal connector (6x) M8x40 Metal dowel
(8x) M6x15 Countersunk socket (2x) M8x90 Countersunk socket
screws screws
(4x) M8x20 Countersunk socket (12x) M8x25 Button screws
screws
(12x) M8x20 Button screws (2x) Steel conical plugs
(2x) Metal straps (24x) Washers
YOU WILL NEED
-5mm Allen Key
-4mm Allen Key
-The help of a friend
NOTES
NOTE 1: Be certain that all assembly is carried out on a at
and stable surface. This will ensure a good nal result.
Reverse the steps to disassemble the piece.
NOTE 2: Your furniture arrives packed in numerous layers that
protect it during transport. It is important that you remove
the packaging carefully to avoid damaging your furniture. Refer
ASSEMBLY INSTRUCTIONS
395Q/V OVERTON TABLE BY MATTHEW HILTON
[e-mail] M
DELAESPADA.COM

0
2
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
OVERTON TABLE
to our information sheet “Unpacking Your Furniture” for further
details.
NOTE 3: Great care is required when assembling our products .
Use blankets to soften the assembly surface - hard surfaces
such as wood or stone ooring may damage the furniture if in
direct contact.
NOTE 4: We advise that assembly and disassembly is undertaken
by a minimum of 3-4 people.
NOTE 5: When screwing in hardware, tighten well, but be sure
NOT TO OVERTIGHTEN. This can cause the thread to strip thus
resulting in a poor connection.
NOTE 6: After assembly, ensure that the table is resting on a
level surface.
IMPORTANT! ALWAYS USE GLOVES WHEN HANDLING BRASS PRODUCTS.
Our brass is coated with a thin layer of wax to embrace the
natural patina that will develop over time. Never handle brass
with your bare hands, as the oils in your skin will cause the
surface to oxidise more quickly in the areas you touch, high-
lighting your nger prints. If you ordered your product in
brass, you will nd white gloves in the supplied hardware box.
INSTRUCTIONS
1. ASSEMBLE THE TABLETOP
a) Place the two halves of the tabletop face down on a clean,
soft surface on the oor, aligning the pre-drilled holes.
[e-mail] M DELAESPADA.COM

0
3
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
OVERTON TABLE
b) Insert Universal Connectors into relevant rebates and insert
metal dowels into the corresponding pre-drilled holes.
c) Push the two halves together, guiding the metal dowels into
the Universal Connectors then tighten with an Allen Key.
[e-mail] M DELAESPADA.COM

0
4
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
OVERTON TABLE
d) The assembly should now look like this.
e) Place a metal strap into the rebate at each end of the
tabletop, and secure with the 8x M6x15 Countersunk socket
screws. Tighten with an Allen Key.
f) Place the assembled tabletop to one side while you construct
the leg structure.
[e-mail] M DELAESPADA.COM

0
5
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
OVERTON TABLE
2. ATTACH CROSS BAR TO LEG FRAMES
Note: When performing this part of the assembly, you will need
one person supporting each leg frame, and one to two people
supporting the central beam.
a) At each end of the cross bar, insert an M8x90 Countersunk
Socket Screw into the top and a conical plug into the bottom.
[e-mail] M DELAESPADA.COM
b) Insert the cross bar into the two leg frames. Then insert 2x
M8x20 Countersunk Socket Screws into the pre-drilled holes in
each end where the cross bar meets the leg. Use an Allen Key to
rmly tighten all connections.

0
6
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
OVERTON TABLE
e) The assembled leg structure looks like this.
[e-mail] M DELAESPADA.COM
3. ATTACH TABLETOP TO LEG STRUCTURE
a) With the help of 2 to 3 friends, ip the tabletop over into
its natural upright position and place it on the leg structure,
aligning the holes in each.

5. Assembly is now complete and the table is ready for use.
0
7
M
A
T
T
H
E
W
H
I
L
T
O
N
ASSEMBLY INSTRUCTIONS CONTINUED
OVERTON TABLE
[e-mail] M DELAESPADA.COM
b) Insert 6x M8x25 Button Screws with washers through each leg
frame and into the underside of the tabletop. Tighten each of
the 12 screws with an Allen Key only loosely until all are in
place. Then tighten rmly.
c) Insert 12x M8x20 Button Screws with washers through the un-
derside of the leg structure cross bar and into the tabletop
and tighten rmly.