decoflame Orlando e-Ribbon Fire User manual

®
Decoflame Technical Information
www.decoflame.com
ORLANDO E-RIBBON™ FIRE
Orlandoe-Ribbon Fire™ is part of the made to measure range of Decoflame bioethanol fires. Its simple layout makes
it versatile and adaptable for a large variety of fireplace applications.
Orlando™ fireplaces can be made in varius layouts, e.g. tunnel and others on request. These variations can be seen
on page 5 in this document, where you can also download the 2D autocad drawing of the fireplace.

®
Decoflame Technical Information
www.decoflame.com
ORLANDO E-RIBBON™ FIRE
TECHNICAL INFORMATION
The example illustrated below is an Orlando open to front LxHxD
1400x400x300mm and Flame tray size: 1200mm.
Capacity: 11,4 L
Fuel consumption: 0,5 L - 1,3L
Burning time: 9h - 23h
Heat output: 2,8 kW - 7,7 kW
Net weight: 71,4kg
Minimum room size: 153m 3
Power supply: 220V - 240V - 50 Hz
Finish: Powder-coated aluminum or brushed stainless steel and
optional hardened, optic-white glass
STANDARD FINISHES OPTIONAL
FEATUR ES
•e-Ribbon™ technology
•8mmaluminiumcasingandbaseplate
•Powder-coatedblackfinestructure
•TouchDisplay
•Bluetooth/Appcontrol
•RemoteControl
•6flamelevelsincludingecowave
•Safetysensors
•Nochimneyrequired
•SleepTimer
•Safetychamber
OPTIONAL
•Made to measure
•Glass screens
•Brushed Stainless Steel finish
•RAL colors
•TV temp. sensor
•Smarthomeconnection
Touch Screen
2D Cad Orlando open to front
Fuel Tank MTM
Length MTM
Height MTM
Glass MTM
Depth MTM
Height MTM
205
162
Flame Tray MTM
Touch display
Fuel inlet
2D Cad Orlando open to front and back

Use non-flammable material inside
the cut-out
Height +10mm
Length + 10mm
Fuel Tank Length + 40 mm
Fuel Tank
Height 190 mm
Fuel Tank Depth 225
Depth + 20mm
®
Decoflame Technical Information
ORLANDO E-RIBBON™ FIRE
Cut-out dimensions
Heat Zone
min. 300mm
min. 1000 mm min. 1000 mm
min. 50mm
HeatZone-Upto60C
Use Appropiate Material
www.decoflame.com
WALL CUT-OUT
Example: Orlando open to front LxHxD 1400x400x300mm and Flame Tray size: 1200mm
The wall cut out will be LxHxD 1410x410x320mm and the recess for the fueltank will be LxDxH
1240x225x190. It is not centered. The distance from the front of the wall to the recess is specified in the
drawing for the fireplace.

®
Decoflame Technical Information
www.decoflame.com
ORLANDO E-RIBBON™ FIRE
1
2
3
4
5
6
Step 1: Make sure that the dimensions of
the cut-out correspond to the measure-
ments indicated in the technical drawing
received with your fireplace. Also be sure
the is no draft inside the wall.
Step 2: Recess the fireplace casing into
the wall cut-out according to the indica-
tions in the User’s manual.
Step 3: Connect the burner to a source
of electricity.
Step 4: Carefully lower the burner with
baseplate in place and fit the frame. At-
tach with screws
Step 5: If the case, place the glass screen
on the top plate by fitting the pin holders
into the holes.
Step6: Turn on the display. Fill in the right
amount of bioethanol by verifying the
level on the display.
Step 7: Start the fireplace by pressing the
ON icon on the display.
Decoflame Bluetooth Application Installation
Orlando Installation
1. Download and install the Decoflame
App by scanning the QR code above cor-
responding to your smart device’s operat-
ing system.
4. Once you have selected your fireplace,
you can turn it on by pressing ‘START’. If the
fireplace has already been turned on us-
ing the display, you can now monitor the
fuel leven and the consumption.
5. For the ‘Turn Off Timer’ press the clock
icon in the lower right corner. To adjust the
remaining time, slide the dot to the left and
right and select ‘SET TIMER’. The remainig
burning time can be changed by repeating
the above mentioned steps. To cancel the
timer select ‘CLEAR TIMER’.
6. For adjusting the flame intesity, select
the desired level on the left side of the
screen.(1-lowest,6-highest)
Should there not be enough fuel for the se-
lected burning time - the fireplace will shut
down automatically.
Select ‘STOP’ tu turn off the fireplace.
2. In order to pair your fireplace with your
smart device, start the fireplace by press-
ing ‘ON’ button and insert the code high-
lighted above.
Note: The code will appear only for a few seconds.
Make sure that you write it down or take a picture
of it.
3. Once your device is paired, the fireplace
should be visible on the app. You are now
able to change the name of the fireplace.
Note: You are able to pair more than one fireplace
like described in the step nr. 2 and give them differ-
ent names.

®
Decoflame Technical Information
www.decoflame.com
ORLANDO E-RIBBON™ FIRE
Decoflame strongly recommends installing one or more glass shields in order to protect the flame from draught, while keeping it
vivid. Please see bellow the situations where the glass is optional and where it is mandatory.
The wall cut-out dimensions for the differnt types of
Orlando e-Ribbon Fireplaces can be found in the
drawings for your specific fireplace or in the auto-
cad drawing available for download on this page.
Open to front
Mandatory glass
Open to front and back
Optional glass
2D Cad Orlando open to front
2D Cad Orlando open to front and back

®
Decoflame Technical Information
www.decoflame.com
ORLANDO E-RIBBON™ FIRE
It is imperative to follow the indications in the User’s manual concerning the installation of decorative or electronic items above
the fireplace.
min. 200mm
min. 100mm
min. 800mm

®
Decoflame Technical Information
www.decoflame.com
ORLANDO E-RIBBON™ FIRE
Take a video tour in our showroom Take a virtual tour in our showroom