decoflame WESTMINSTER DS Manual



™

FRAME StAndARd FiniSh
This impressive bioethanol replace is the perfect solution
when challenged with the task to restore an old, reduant re-
place or merely the opening remaining in a chimney breast
from a previously model.
It is a one-piece bioorelplace easing the installation. It comes
complete with a metal frame, insert, basket and the e-Ribbon
Basic burner.
The frame and decor can be manufactured in di󰀨erent n-
ish and materials but comes standard in black/black or black/
brushed stainless steel.
tEchnicAl inFoRMAtion
Capacity: 4L
Burning time: 7-20 hours (Depending on ameintensity)
Heat e󰀩ency: 1.2 - 3.2 kW/h
Net weight: Depends on material
Minimum room size: 64m3
Burner: Denver e-Ribbon Basic 720
Flametray: 500mm long in aluminium
Materials: Aluminium and steel
Hardened diamond clear glass 80mm high, 6mm
Finish: Powder coated black
Standard nish frame Powder coated black
Brushed stainless steel (BSS)
Power supply: 220V - 240V / 50 Hz
Fuel: Use bioethanol at 96.5 - 97.5%
FEAtuRES
• e-Ribbon™ technology
• Safety Sensors / Safety Chamber
• Fuel Level Indicator / Flame Level Indicator
• Remote control
• Bluetooth / App
• 6 ame levels (1-5 + ECO-Wave)
• No chimney required - no smoke, ash or soot
BioEthAnol

(Please be aware that bioethanol is essential to a proper use and gurantee of your product).

FRAME optionAl on REQuESt
850mm
760mm245mm



 










Subject to typing errors, typos and technical faults, production- and product tolerances. Decoame ApS reserves the right to make changes without notice. We refer to Decoames Ordinary Terms and Conditions.


1. Download and install the Decoame App by
scanning the QR code above corresponding to
your smart device’s operating system.
4. Once you have selected your replace, you
can turn it on by pressing ‘START’.
If the replace has already been turned on us-
ing the control panel, you can now monitor the
fuel level and the consumption.
5. For the ‘Turn O󰀨 Timer’ press the clock icon
in the lower right corner. To adjust the remain-
ing time, slide the dot to the left and right and
select ‘SET TIMER’.
The remaining burning time can be changed
by repeating the above mentioned steps. To
cancel the timer select ‘CLEAR TIMER’.
6. For adjusting the ame intesity, select the
desired level on the left side of the screen.
(1-lowest and depending on model 5-highest
+ Eco-Wave or 6-highest). Should there not be
enough fuel for the selected burning time - the
replace will shut down automatically.
Select ‘STOP’ to turn o󰀨 the replace.
2. In order to pair your replace with your
smart device, start the replace by pressing
the ‘ON’ button.
Start the App and choose your replace.
Insert the code from YOUR rating plate, like
the one highlighted above.
3. Once your device is paired, the replace
should be visible on the app.
You are now able to change the name of the
replace.

Control Panel Flame level indicator
1-5 + ECO-Wave
Fuel level indicator
START/STOP the replace
Adjust the ame level up
Service USB
On / Off
Adjust the ame level down
Fuel tank
Use the supplied remote
control or download the
Decoame App to your
mobile device for con-
trolling the bioreplace.
Step 1 Turn on the electronics of your Denver e-Ribbon Basic™ by pressing the button.
Step 2 Fill in the right amount of bioethanol in the fuel tank by verifying the level on the fuel level indicator.
Step 3 To ignite the replace: Press the button on the control panel.
After about 3 minutes, the rst ames will appear around the centre of the ame tray.
Step 4 When the lament no longer is red/glows (approx. 10 min) it is possible to adjust the ames.
Step 5 To switch o󰀨 the re at any time – also during the warming-up phase – press the button on the
control panel. The ames will disappear within few minutes.
Filament
