DeLonghi HOR KH590715 User manual

instructions
Please retain these instructions for future reference
Electric oil Filled Radiator

Electric oil filled radiator
2
A
B
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
13
18
17
14
15
16
Single notch
Arrow indicator
Operating time
Fig.3
Fig.1
Fig.4
Fig.2
Fig.5 Fig.6 Fig.7
Fig.8

3
Thank you for choosing this De’Longhi radiator. To get the
very best out of your new radiator it is advisable to read
these instructions before using it.This will ensure that you
gain optimum results and use the appliance safely.
General instructions
Ta ke the radiator out of its packing box and remove any polstyrene
pieces or any other packaging material that might be lodged inside it.
Make sure that the radiator has not been damaged during transit and that
the mains cable is in working order.Do not operate the radiator if damaged.
Fitting the feet
Remove the feet and the castors from the polystyrene packing.
Fit the castors to the spindles on the feet and push firmly until they click
into position (fig. 1). Pull each castor to check that it is fitted correctly.
In certain models, the castors are already mounted on the feet.
Using the threaded u-bolt and wing nuts, fit the feet to the bottom of the
radiator between the last two elements as shown in figures 2, 3 and 4.
Depending on the type supplied, type Aor type B,mount the feet as
shown in figure 5 or 6.
Models with “Easy wheel” sytem
Turn the radiator upside-down on a rug or a soft surface in order to
prevent damaging the paint finish. Fully unfold the castors by turning
them outwards (Fig.7).Turn the radiator back to its upright position.
Important
When in use, the radiator should always be kept vertical (wheels at the
bottom, controls at the top).Any other position could be dangerous!
Electrical connection
-Before plugging the radiator into the mains, check that your supply
voltage is the same as that shown on the rating plate of the appliance.
- If using more than one radiator at a time, it is important to ensure
that the ring main is adequate to cope with the power requirements.
- It is important to ensure that the socket is adequately earthed.
- This radiator complies with EEC Directive 89/336 relating to elec-
tromagnetic compatibility.
Switching on
Plug into the mains socket.Turn the thermostat to maximum. Switch
the radiator on using the switch/switches following the procedures
given in points a) - b).
a) Models with single switch (1 power level):
-button in position «I» = Total power on (indicator light on);
-button in position «O» = (indicator light off)
b) Models with double switch (3 power levels)
-button in position «l» = minimum power (indicator light on);
-button in position «ll» = intermediate power (indicator light on);
-both buttons in position «l» «ll» = maximum power (indicator lights on)
To turn appliance off, switch off both switches or remove plug from
wall socket.
Electric oil filled radiator

Adjusting the thermostat
When the room has reached the required temperature, turn the
thermostat slowly anticlockwise until the indicator light goes out (or
until you hear a "click") and no further.The set temperature will then
be regulated automatically and kept constant by the thermostat.
Frost protection function
With the thermostat in position and the switches pressed, the
appliance maintains the room at a temperature of about 5˚C, pre-
venting freezing with minimum energy consumption.
c) Models with a 24 hour time-clock (fig. 8)
To programme heating, proceed as follows:
-Look at the time on your clock or watch. If it is 10.00, turn the
numbered timer disk clockwise until the number 10 on the disk
coincides with the pointer ▲on the timer. Set the periods of
time when you want the appliance to work by pushing the teeth
inwards. Each tooth corresponds to a period of 15 minutes.This
will leave visible sectors which correspond to the periods of
operation. When set, the radiator will operate automatically
each day during the times programmed (important: the radiator
must always be plugged into the socket).
-To change the programming, move the teeth back into the initial
position and set the new periods of functioning.
-If you want to make the appliance operate without program-
ming, push all the teeth into the centre. In this case, to turn the
appliance off completely, as well as turning the switches off, you
must also unplug it from the mains to avoid continued operation
of the timer.
Turbo heating
Some models are fitted with a heating fan which heats the room more
quickly. To turn this function on, push the button into the position.
Important: a safety device cuts in and switches off the appliance if it
overheats due to an accumulation of dust on the air intake and out-
put grills.To restart it, unplug from the mains and leave the applian-
ce to cool down. Clean the air intake and output grills with a vacuum
cleaner, then replug into the mains and turn on again.
Cleaning and Maintenance
Before carrying out any maintenance, unplug the radiator from the mains
and wait for it to cool. The oil-filled electric radiator requires no particu-
lar maintenance. It is sufficient to remove the dust with a soft, dry cloth.
Never use abrasive powders or solvents. If necessary remove concen-
trated areas of dirt with a vacuum cleaner.
Warnings
-Do not use your radiator in the vicinity of showers, bathtubs,
sinks, swimming pools etc.
-Never use your radiator to dry laundry.
-Never place the power cable on top of the radiatorwhile it is hot.
-Only use the heater in an upright position.
*
3
Electric oil filled radiator

-The heater must be positioned at least 50cm from furniture or
other objects.
-If the supply cord is damaged, it must be replaced by the manufac-
turer, its service agent or similarly qualified persons in order to
avoid a hazard.
-It is normal for the heater to make 'crackling' noises during the
first time it is switched on (or in the case of infrequent use)
-The body of your radiator is filled with an exact quantity of oil. If
repairs are necessary which call for the opening of the radiator,
they must be done only by the manufacturer or an authorised
service centre. In the unlikely event of oil leakage, contact the
manufacturer or an authorised service centre.
-Do not use your radiator in rooms which have an area smaller
than 4m2as this may lead to overheating.
-The heater must never be placed immediately under a fixed mains
socket.
-When scrapping the appliance, respect legislation on the disposal of
oil.
-The use of an extension lead is not recommended, however if it is
neccessary then follow carefully the extension lead’s instructions, and
most importantly ensure that the extension lead is correctly rated in
accordance with the heater being used and NEVER overloaded.
-As with any electrical appliance, whilst the instructions aim to
cover as many eventualities as possible, caution and common
sense should be applied when operating your appliance, particular-
ly in the vicinity of young children.
ATTENTION: in order to avoid any danger caused by an accidental
resetting of the safety system, this appliance must not be powered
through an external timer.
IMPORTANT: Never for any reason cover the radiator
during operation as this could lead to dangerous over-
heating.
If this recommendation is not respected, a safety device will
turn the radiator off.To reset, contact the technical assistan-
ce service.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF
THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE
2002/96/EC.
At the end of its working life, the product must not be dispo-
sed of as urban waste. It must be taken to a special local autho-
rity differentiated waste collection centre or to a dealer pro-
viding this service. Disposing of a household appliance separa-
tely avoids possible negative consequences for the environ-
ment and health deriving from inappropriate disposal and ena-
bles the constituent materials to be recovered to obtain signi-
ficant savings in energy and resources.As a reminder of the
need to dispose of household appliances separately, the pro-
duct is marked with a crossed-out wheeled dustbin.
5
Electric oil filled radiator

6
Electric oil filled radiator
Electrical requirements
Before using this appliance ensure that the voltage indicated
on the product corresponds with the main voltage in your
home, if you are in any doubt about your supply contact your
local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug
having a fuse of 13 amp capacity. Should this plug not fit the socket out-
lets in your home, it should be cut off and replaced with a suitable plug,
following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should
therefore be properly disposed of and not left where children might find
it and plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that
can be switched off when the machine is not in use.
important: the wires in the mains lead fitted to this appliance are
coloured in accordance with the following code:
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
The wire which is coloured green and yellow must be connected to the
terminal in the plug which is marked with the letter E or by the earth
symbol or coloured green or green and yellow.
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely
retained in each terminal. Do not forget to tighten the mains lead clamp
on the plug. If your electricity supply point has only two pin socket out-
lets, or if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this
operation be carried out by a qualified electrician and should only be
replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted.
If the fuse cover is lost, the plug must not be used until a replacement
cover is obtained. The colour of the correct replacement fuse cover is
that of the coloured insert in the base of the fuse recess or elsewhere
on the plug. Always state this colour when ordering a replacement fuse
cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362
should be fitted.
This appliance conforms to the Norms EN 55014 regarding the sup-
pression of radio interference.
GREEN ANDYELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
Green and Yellow to Earth
Blue to
Neutral
13 amp
Fuse
Brown
to Live
Cord Clamp
Warning - this appliance
must be earthed
5708012800/07.05