DeLonghi HWB Series User manual

FAN HEATER

A) If your appliance comes tted with a plug, it will incorporate a 13 Amp fuse. If it does not t your socket, the plug should
be cut o from the mains lead, and an appropriate plug tted, as below.
WARNING:Very carefully dispose of the cut o plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in
the house as this could cause a shock hazard.
With alternative plugs not incorporating a fuse, the circuit must be re-tted when changing the fuse using a 13 Amp Asta
approved fuse to BS 1362. In the event of losing the fuse cover, the plug must NOT be used until a replacement fuse cover
can be obtained from your nearest electrical dealer.The colour of the correct replacement fuse cover is that as marked on
the base of the plug.
B) If your appliance is not tted with a plug, please follow the instructions provided below:
Important
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which si marked with the letter L or coloured red.
ELECTRICAL CONNECTION (UK ONLY)

45
IMPORTANT INFORMATION
Danger!
Failure to observe the warnings may result in life-threatening
injury by electric shock.
- The device should not be placed im-
mediately under a xed power socket.
- Do not use the appliance near show-
ers, bathtubs, sinks, swimming pools,
etc.
- If the power cable is damaged, it must
be replaced by the manufacturer, its
service centre or a qualied electrician
so as to eliminate all risk.
- Theappliance mustbeinstalled so that
the controls are not accessible by those
who are using a bath or shower.
Important!
Failure to observe the warning could result in injury or dam-
age to the appliance.
-This appliance can be used by children
at least 8 years old and by persons with
reduced physical, mental and sensory
capacities or with inadequate experi-
ence and knowledge, as long as they
are carefully supervised or instructed
on how to safely use the appliance and
the hazards involved.
Make sure that children do not play
with the appliance. Cleaning and
maintenance performed by the user
must not be performed by children
without supervision.
- Children less than 3 years old should
be kept away from the appliance un-
less continuously supervised.
- Children between 3 and 8 years old
may only switch the appliance on and
o, provided that it has been placed or
installed in its normal operating posi-
tion, they are carefully supervised and
instructed concerning use of the ap-
pliance in a safe way and they under-
stand the hazards involved.
Children between 3 and 8 years old
should not insert the plug, adjust and
clean the appliance or perform main-
tenance on it.
ATTENTION: Some parts of the ap-
pliance can become very hot and
cause burns. Pay particular atten-
tion when children and vulner-
able persons are present.
- IMPORTANT: To avoid the risk of
the safety cuto device resetting ac-
cidentally, this appliance must not be
powered through an external on/o
device such as a timer, nor connected
to a circuit which is turned on and o
regularly by the energy supplier.
Danger of burns!!
Failure to observe the warning could result in burns.
- IMPORTANT: To avoid over-
heating, never under any cir-
cumstances cover the appliance
during operation as this would lead to
a dangerous rise in temperature.
Note:
This symbol indicates recommendations and important infor-
mation for the user.
- Always use the appliance in an upright position.
- The use of extension leads is not recommended. How-
ever if they cannot be avoided, carefully follow the in-
structions accompanyingthe extension lead,takingcare
to not exceed the power limit marked on the extension
lead.
- There must be no furniture or other objects in the 50 cm
in front of the appliance.
- Do not use the appliance in rooms whose surface area is
less than 4 m².
- Before moving the appliance, make sure it is completely
turned o and it is unplugged from the power socket.
- Do not position it in dusty atmospheres.

45
- Do not rest anything on the appliance.
- Do not obstruct the air intake and outlet grilles (danger
of overheating).
- Do not use the appliance near walls, furniture, curtains,
etc.
- When you rst use the device it may release an odour
due to heating up. It is advisable to ventilate the room.
Safety features
- Safety device: the appliance is tted with a safety cut-
o device which switches it o in the event of accidental
overheating (e.g. obstruction of air intake and outlet
grilles, motor turning slowly or not at all).
To reset the cuto, disconnect the appliance from the
power socket for a few minutes, remove the cause of
overheating then reconnect to the power supply.
If the problem persists or the appliance does not return
to normal operation, do not use it and contact an au-
thorised service centre to resolve the problem.
Disposing of the appliance
The appliance must not be disposed of with house-
hold waste but must be taken to an authorised waste
separation and recycling centre.
DESCRIPTION
(see p. 3)
A Function selector
B Warning lamp
C Room thermostat
D Timer (if provided)
ETowel rail (select models only)
F Pedestal (select models only)
USE
Electrical connection
-Before plugging into the power socket, make sure that
the voltage of your power system corresponds to the
value in Volts indicated on the appliance and that the
power socket and power line are suitable for the electri-
cal load.
- THIS APPLIANCE COMPLIES WITH DIRECTIVE 2004/108/
EC ON ELECTROMAGNETIC COMPATIBILITY.
Installation
The device should only be used in an upright position.
Models with towel rail
Some models are equipped with a towel rail (E) that provides
a drying function and can be used only with the appliance
xed to the wall.
If the unit is used in a bathroom, to avoid hazards, it must be
installed as shown in g. 4. If installed in another room the
minimum distances shown must be respected.
The wall-mount kit includes:
1 bracket
2 x screws
2 x wall plugs (0.6x30)
Install as follows:
1. Remove the bracket mounted on the back, pulling it
downwards.
2. Choose the point to install the appliance ensuring that:
a. The plug and the socket are easily accessible after instal-
lation.
b. Neither the electrical cables nor other pipework can be
damaged.
c. Curtains or other ammable material are kept away
from the appliance.
3. Before drilling the wall, mark the exact points as shown
in g.1.
4. For brick walls, use a 6 mm masonry bit. Drill and insert
the wall plugs provided. (For plasterboard or false walls
we suggest that you locate the wooden battens behind
and use wood screws size 6 directly into the wood or
special anchors.
For any other type of wall ask the advice of a specialist.
5. Secure the bracket with the two screws provided.
Next, insert the appliance into the top and bottom
hooks of the bracket, and then lightly press the unit
down.
Slowly lift the rail (E) to the rst stop. To avoid overheating
problems in this mode, the heat setting should not exceed
1000W.
At this point you can hang towels or sheets on the rail for dry-
ing. When the appliance is not used in drying mode lift the
arm upwards up to the top which unlocks it and then bring
it down.
Attention! Do not overload the towel rail (E) and pay
special attention to drying of delicate fabrics.
Models with pedestal
Models equipped with pedestal (F) can be used in a portable
version with the pedestal or wall-mounted, excluding the
need for the pedestal in the second case.
To remove the pedestal (F) press the two tabs on the back of
thebase whilepushing theheater forwardsthenraise theap-

6TM
pliance.The two tabs are identied by the word "PUSH" (g-
ure 2/3). If you want to install it to the wall, however, proceed
as described for models with towel rail.
OPERATION AND USE
1. Make sure the appliance is turned o before insert-
ing the plug into the power socket and turning on the
socket switch if necessary.
2. Turn on the appliance by placing the thermostat (C) in
the maximum position and the function selector (A) in
one of the following positions: /1/2.
- Summer (fan only): turn the function selector (A) knob
clockwise to position.
- Min power operation: Turn the function selector (A)
to position "1". The red warning lamp lights up.
- Max power operation: Turn the function selector (A)
to position "2".
- To switch o the appliance: Turn the function selec-
tor to position "l".
Adjusting the thermostat
When the room has reached the desired temperature, slowly
move the thermostat counterclockwise until the indicator
light turns o and no further.
The temperature thus xed will be automatically maintained
by the thermostat.
Freezing prevention
With the thermostat knob at the minimum position and
the function selector at pos. 2 the appliance keeps the am-
bient temperature at about 5°C, preventing freezing with a
minimum expenditure of energy.
MODELS WITH 24-HOUR TIMER (if provided)
To program the heating proceed in the following way:
Look at the time on your watch. If it is 10.00 for example, turn
the numbered programmer disk until the number 10 coin-
cides with the index mark s imprinted on the programmer.
Set the periods of time that you want the appliance to func-
tion, pushing the teeth toward the centre. Each tooth corre-
sponds to a period of time of 15 min. At this point you will see
the red sectors that correspond to the periods of operation.
Set up in this way, the unit will work automatically every day
during the scheduled periods. (Important: the plug must be
always inserted in the power socket and the socket switched
on if necessary).
- To change the programming, simply return the red teeth
to the initial position and set the new operating periods.
- If you want to operate the appliance without program-
ming, push all the teeth toward the centre. In this case,
for total shutdown of the appliance, as well as turning
o the switches, it is also necessary to remove the plug
from the power socket, to avoid unnecessary operation
of the programmer.
MAINTENANCE
- Before cleaning, always remove the plug from the pow-
er socket.
- Regularly clean the air intake and outlet grilles.
- Never use abrasive powders or solvents.
TECHNICAL CHARACTERISTICS
Power supply See appliance rating plate
Power consumption “