DELTA DORE DME 90 Tyxal+ User manual

* Up to 10 years valid under the conditions of use specied in the installation instructions and the General Conditions of Sale
EN Outdoor motion detector
DME 90 Tyxal+

- 2 - - 3 -
EN
Do not direct the lower detection zone towards
reflecting surfaces (puddle, window, etc.).
Do not direct the detector towards moving objects
(leaves, bushes, flags, etc.).
N°1
N°6
N°4
N°3
N°2
N°5
N°7
Install the motion detector vertically, with its
high detection zones parallel to the ground.
If the detector is installed at an angle,
detection reliability may be compromised.
Install the motion detector vertically, with
both high and low detection zones parallel
to the wall.
To make sure the device functions properly,
attach the motion detector to the wall.
Do not install close to a heat pump or heat
evacuation outlet (dryer, etc.).
3. Location
Instructions
Important
Product
Informations
1. Contents
N°1
N°6
N°4
N°3
N°2
N°5
N°7
Installation height: between 0.8 m and 1.2 m
2. Presentation
TYXAL+ DME 90 is a passive infrared motion detector, designed to detect the infrared
radiation emitted by human bodies.
This motion detector aims to protect the outside of a building by detecting intrusions prior to
penetration into the premises.
As soon as a presence is detected, it raises the alarm.
TYXAL+ DME 90 has an automatic system to protect it against being opened or ripped from
its mount.
It is also equipped with anti-masking detection, to prevent attempts to mask the lens.
• Paired with a control unit:
- alarm signal.
- pre-alarm signal: as soon as a person enters the protected zone, a sound and visual
signal (outdoor siren) warns you of the imminent alarm.
Read the entire guide before starting
to install the device.
!
Note
This product detects temperature differences between moving and background targets
within the detection zone.
If the target remains motionless, the motion detector cannot detect it. This may affect the
detector's maximum detection range.
For optimal operation, please comply with the following recommendations:
In the event of non-compliance, the product may present malfunctions or may not function
optimally.
3. Location

- 4 - - 5 -
EN
Do not touch the lenses.
!
❶Unlatch the top cover.
❷Remove the top cover.
❸Remove the fixing screws
Remove the sensor/electronic card assembly
❺
Do not touch the mirrors.
❹Remove the fixing
screws and remove
the base from the rear
mount.
4. Mounting
Support mural Support poteau
Bande de métal
25 mm max.
❻Attach the rear mount to the wall
using the fixing screws provided,
then attach the base onto the rear
mount
5. Commissioning / Detection test
❶Plug the battery cable into the card
connector.
Set the (Tyxal+) alarm control panel to
‘pending pairing’, then press the pairing
button on the card. ❷Reposition the sensor/elec-
tronic card into the rear mount
and secure in place
Only the blue parts are actionable.
❸Close the product up again
Wall-mounted Pole mount
Collar (not sup-
plied)
❹A 3-minute detection test launches
automatically.
Let it run for 3 minutes.
Check where the detection zone is a,d
whether you are detected as desired.
❺ With each detection, the LED ashes for 5 seconds.
Test mode automatically stops after 3 minutes and the
system returns to "Normal" mode.

- 6 - - 7 -
EN
❸
To conceal the zones:
Remove the lens
from the top cover
Conceal the concerned section using stickers
from sheet 1.
You have a choice of 5 lens masking kits (see
§ special detection zone). Reposition the lens in the top
cover
Hindrance
(e.g. tree)
6. Detection zone seings
Principle:
The high beam always remains parallel to the ground.
The low beam can be adjusted as shown below.
The range is limited by the angle of the low beam as the high and low beams must be
intercepted simultaneously in order to activate the detector.
7. Detector range seings
To change these settings:
Change the detection range by sliding the lower infrared cell to the desired position.
If only the high beam is intercepted:
No detection
The high and low beams are intercepted:
Detection
If only the low beam is intercepted:
No detection
Principle: Because the protection zone can be disrupted by various elements (leaves,
reflective surface...), you have the ability to select its orientation.
To change the orientation and detection zones:
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
D
ABCEFG
Change the detection zone's settings
by pivoting the system on its axis.
Position
D
(by default)
Position
A
Position
Ë
Position
C
Position
G
Position
B
Position
F

- 8 - - 9 -
EN
❹Select a masking sticker (2 to 6),
according to the shape of the
chosen zone (see diagram).
Stick it to the lens.
Use masking stickers 2 to 6.
You can define a special detection zone for horizontal positions A or G.
❶Set the lower
detection zone to
position 1
❷Set the zone's
direction (A or G)
❸If another position is used,
cut off the part to be eliminated
in the lens' lower mount.
8. Special detection zone
8. Special detection zone
7. Detector range seings
Select the desired position (1,2,3,4 or 5).
The low beam can be adjusted to control the range, as per the table below.
Put the top cover in its place to perform an automatic detection test.
The LED flashes with each detection.
1m
1m
1m
1m
1m
Position 5 (2.5m)
Position 1 (12 m)
Position 2 (8.5 m)
Position 3 (6 m)
Position 4 (3.5 m)
* Installation height = 1 m.
Standard environment = T° of 20°C with
no direct sunlight.
** The maximum range may be influenced
by ambient thermal conditions.
Position Standard
range *(m)
Maximum
range ** (m)
112 10 - 17
28,5 7 - 12
36 5 - 8,5
43,5 3 - 6
52,5 2 - 3,5
a
b
c
d
e
fghi
j
k
l
m
na
b
c
d
e
fghi
j
k
l
m
n
a
b
c
d
e
fghi
j
k
l
m
n
a
b
c
d
e
fghi
j
k
l
m
na
b
c
d
e
fghi
j
k
l
m
n
m21m21
12 m
m01m01
10 m
m5m5
5 m
m21m21
12 m
m01m01
10 m
m5m5
5 m
m21m21
12 m
m01m01
10 m
m5m5
5 m
m21m21
12 m
m01m01
10 m
m5m5
5 m
m21m21
12 m
m01m01
10 m
m5m5
5 m
Both sides
5 × 10 m 1.5 × 10 m
10 × 5 m 10 × 1.5 m
G A
G A
G A
G A
G A
3
2
4
5 6
❺Put the top cover in place to launch an automatic detection test.

- 10 - - 11 -
EN
9. Function seings
The sensitivity can be set to 3 different positions:
• L (low),
•M(medium),
•H(high),
The chosen position will depend on environmental
conditions.
Detection sensitivity settings
We recommend that you set the sensitivity level
to H (high):
• When the detection beams were tilted horizontally.
• When higher sensitivity is required towards the end
of the detection zone (12 m).
to L (low):
• When the device is installed in a mediocre location
(bad conditions).
• When there is a high risk of faulty detection.
Switches 1, 2 and 3 must remain in the
OFF position
Do not change this setting.
Anti-masking function
• OFF position: Function inactive
• ON position: Function active
The masking of the lens is indicated by an
Auto-Protection fault.
Switch settings
Switch 4
1
ON
2 3 4
OFF ON
• Association with an alarm system
• Pre-alarm
• Selection of triggering method
• Test
Read system
installation guide
10. Operation with an alarm system
11. Baery replacement
The LED flashes continuously, the battery is dead.
Before opening the unit, the alarm control unit must be in "Maintenance" mode (refer to
system installation guide).
❶ ❷ ❸
Problem Probable cause Sustainable
The LED flashes
continuously. Incorrect power supply. Change the battery.
Triggered detection
without any objects
moving
The motion detector was not
installed
perpendicularly to the ground.
Install the motion detector
correctly.
A reflecting object is located within
the detection zone.
Eliminate all reflecting surfaces
from the detection zone, or conceal
part of the detection zone.
The lower beam is longer than
expected.
Check and readjust the detection
beam.
The lower detection beam is
exposed to direct sun rays or to car
headlights.
Readjust the detection beam
so it is no longer exposed to direct
light sources.
Presence of a heat source (heating
device, etc.) in the detection zone
that may cause the temperature to
change.
Readjust the detection beam or
eliminate the heat source in the
detection zone.
An object is moving (washing hung
up on a line, plants, etc.).
Readjust the detection beam or
remove moving objects.
In the event of heavy rain, water
may pour through the detection
zone (overflowing gutter, roof/
terrace/balcony drainage, etc.)
Readjust the detection beam
so it is no longer directly exposed
to the flowing water.
Occasionally no
detection.
Occasionally no detection. Readjust the detection beam
correctly.
Sensitivity is set to L (low). Readjust the sensitivity level
to M (medium) or H (high).
12. Troubleshooting

www.deltadore.com
Caractéristiques techniques / Technical characteristics / Technische Daten
Caraeristiche tecniche / Características técnicas / Technische kenmerken
2xLS 14500 - 3.6 V / 5.2 Ah - Lithium
Consumption stand-by : 9 µA
Consumption : 4 mA max / 3 Vcc
[868 - 868.6] MHz and
[868.7 - 869.2] MHz
100 m Ý 300m
Maximum power radio < 10 mW,
receiver category: 2
-10°C / +70°C
-20°C / +60°C
IP IP 55
95%
81,6 x 199,3 x 109,3 mm
500 gr.
Important product
information (❸)