DELTA DORE Tyxal+ DME 180 User manual

* Up to 10 years valid under the conditions of use specied in the installation instructions and the General Conditions of Sale
EN
Outdoor motion detector
DME 180 Tyxal+

- 2 - - 3 -
EN
N°1
N°6
N°4
N°3
N°2
N°5
N°7
3. Location
1. Contents
Instructions
Important
Product
Informations
2. Presentation
TYXAL+ DME 180 is a passive infrared motion detector, designed to detect the infrared
radiation emitted by human bodies.
This motion detector aims to protect the outside of a building by detecting intrusions prior to
penetration into the premises. As soon as a presence is detected, it raises the alarm.
TYXAL+ DME 180 has an automatic system to protect it against being opened or ripped from
its mount.
It is also equipped with anti-masking detection, to prevent attempts to mask the lens.
2 installation heights are possible:
- low position, between 0.8 and 1.2 m: 180° detection, 12 m range.
- high position, 2 m : 180° detection, 9 m range.
• Paired with a control unit:
- alarm signal.
- pre-alarm signal: as soon as a person enters the protected zone, an audible and visual
signal (outdoor siren) warns you of the imminent alarm.
Read the entire guide before
starting to install the device.
!
Note
This product detects temperature di󰀨erences between moving and background targets
within the detection zone.
If the target remains motionless, the motion detector cannot detect it. This may a󰀨ect the
detector's maximum detection range.
N°1
N°6
N°4
N°3
N°2
N°5
N°7
For optimal operation, please comply with the following recommendations:
In the event of non-compliance, the product may present malfunctions or may not function
optimally.
2 installation heights are possible:
- low position, between 0.8 and 1.2 m: 180° detection, 12
m range.
- high position, 2 m : 180° detection, 9 m range.
3. Location Do not direct the lower detection zone towards
reecting surfaces (puddle, window, etc.).
Do not direct the detector towards moving objects
(leaves, bushes, ags, etc.).
Install the motion detector vertically, with
both high and low detection zones parallel
to the wall.
To make sure the device functions properly,
attach the motion detector to the wall.
Do not install close to a heat pump or heat
evacuation outlet (dryer, etc.).
Install the motion detector vertically,
with its high detection zones parallel
to the ground.
If the detector is installed at an angle,
detection reliability may be
compromised.
An integrated spirit level enables
optimal installation.

- 4 - - 5 -
EN
Do not touch the lenses.
!
❶Unlatch the top cover to open it.
❷Press on the "Push" strip to separate the
detector from its base.
❸Secure the base to the mount
using suitable screws and dowels.
The tamper is triggered when the
bottom is broken and remains on the
wall.
Do not touch the mirrors.
4. Mounting
Only the blue parts are
actionable.
Wall-mounted On a post
Use screws and dowels that are compatible
with the mount.
You can mount it onto a post
using clamps (not provided).
0.8 - 1.2 m
5. Activation
❶Plug the battery cable into the card connector.
Set the (Tyxal+) alarm control panel to ‘pending
pairing’, then press the pairing button on the card.
Important: only the blue/green wires must be
connected to the wireless car (and not the grey/
yellow wires).
❷Reposition the sensor/electronic
card on the base
Attention: lock the detector part by
pushing the "Push" strip until you
hear a "click".
❸Close the cover
❹A 3-minute detection test launches
automatically.
Check that you are detected by moving into the
detection zone.
❺ With each detection, the LED ashes for 5
seconds.
Test mode automatically stops after 3 minutes
and the system returns to "Normal" mode.

- 6 - - 7 -
EN
6. Detection zone seings
abc
e
f
g
h
i
j
k
l
m
n
d
f
g
h
i
j
e
abc
Blue
The detection zones from a to n can be easily
masked by turning the masking shutter.
The masking of a zone enables the prevention
of false alarms.
h
abc
e
f
g
i
j
k
l
m
n
d
1
2
Zone h
masked
Masking plate option
You have 5 masking plates to block out specidic detection zones.
Example: masking of zone h.
7. Detector range seings for each side
Principle:
The high beam always remains parallel to the ground.
The low beam can be adjusted as shown below.
The range is limited by the angle of the low beam as the high and low beams must be
intercepted simultaneously in order to activate the detector.
If the high beam alone is cut through:
No detection
The high and low beams are intercepted:
Detection
If only the low beam is intercepted:
No detection
The detection distance can be easily independently adjusted
between 2.5 m and 12 m, by sliding the control button on the PIR.
For example: you can select 12 m on the left and 6 m on the right
to adjust the installation to suit environmental constraints.

- 8 - - 9 -
EN
Low mounting
2.5 m (8 ft.)
3.5 m (12 ft.)
6.0 m (20 ft.)
8.5 m (28 ft.)
12.0 m (40 ft.)
1.0
(3)
12.0 10.0 5.0 0
(40) (33) (17)
12.0 10.0 5.0 0
2.5 m (8 ft.)
3.5 m (12 ft.)
6.0 m (20 ft.)
8.5 m (28 ft.)
12.0 m (40 ft.)
1.0
(3)
0 5.0 10.0 12.0
(17) (33) (40)
0 5.0 10.0 12.0
12.0 10.0 5.0 0
12.0 10.0 5.0 0
12.0 10.0 5.0 0
0 5.0 10.0 12.0
0 5.0 10.0 12.0
0 5.0 10.0 12.0
L2.5
L3.5
L6.0
L8.5
L12
/H9
(m)
L8
L12
L20
L28
L40
/H30
(ft.)
Right side
Left side
2.0 m (6’7”)
L8
L12
L20
L28
L40
/H30
(ft.)
HIGH MNT
nml
k
j
i
h
g
f
e
d
c
b
0 5.0 9.0
(17) (30)
9.0
(30)
5.0
(17)
0
5.0
(17)
9.0
(30)
0 5.0 9.0
(17) (30)
a
1.0 (3’ 3” )
2.0 (6’ 7” )
High mounting
8. Detector range seings
If the detector is installed at a height of 2 m.
In this case, the detection distance is limited to max. 9 m.
You must perform the following steps:
❶Position the cursor at L12/H9 (left side)
and L40/H30 (right side).
❷Reassembly the entire assembly to
make the "HIGH MNT" marking appear.

- 10 - - 11 -
EN
9. Function seings
The sensitivity can be independently adjusted for
each side, (L) left and (r) right, to 3 positions:
• L (low),
•M(medium),
•H(high),
The chosen position will depend on environmental
conditions.
Detection sensitivity settings
We recommend that you set the sensitivity level
to H (high):
• When the detection beams were tilted
horizontally.
• When higher sensitivity is required towards the
end of the detection zone (12 m).
to L (low):
• When the device is installed in a mediocre
location (bad conditions).
• When there is a high risk of faulty detection.
The switches must be positioned towards the
bottom during normal operation.
Switch 8: anti-masking function
• OFF position: Function inactive
• ON position: Function active
The masking of the lens is indicated by an Auto-
Protection fault.
Switch settings
12345678
KSD82S
• Association with an alarm system
• Pre-alarm
• Selection of triggering method
• Test
Read system installation
guide
10. Operation with an alarm system
12345678
KSD82S
11. Baery replacement
The LED ashes continuously, the battery is dead.
IMPORTANT: Before opening the unit, the alarm control unit must be in Maintenance mode
(refer to system installation guide).
❶Unlock the cover to open it.
❷Press on the "Push" strip to separate the
detector from its base.
Problem Probable cause Solution
The LED ashes
continuously. Incorrect power supply. Change the battery.
Triggered
detection without any
objects moving
The motion detector was not installed
perpendicularly to the ground.
Install the motion detector
correctly.
A reecting object is located within
the detection zone.
Eliminate all reecting surfaces from
the detection zone.
The lower beam is longer than
expected.
Check and readjust the detection
beam.
The lower detection beam is
exposed to direct sun rays or to car
headlights.
Readjust the detection beam
so it is no longer exposed to direct
light sources.
Presence of a heat source (heating
device, etc.) in the detection zone
that may cause the temperature to
change.
Readjust the detection beam or
eliminate the heat source in the
detection zone.
An object is moving (washing hung
up on a line, plants, etc.).
Readjust the detection beam or
remove moving objects.
In the event of heavy rain, water
may pour through the detection zone
(overowing gutter, roof/terrace/
balcony drainage, etc.)
Readjust the detection beam
so it is no longer directly exposed to
the owing water.
Occasionally no
detection.
Occasionally no detection. Readjust the detection beam
correctly.
Sensitivity is set to L (low). Readjust the sensitivity level to M
(medium) or H (high).
12. Troubleshooting

www.deltadore.com
Caractéristiques techniques / Technical characteristics / Technische Daten
Caraeristiche tecniche / Características técnicas / Technische kenmerken
2xLS 14500 - 3.6 V / 5.2 Ah - Lithium
Consumption stand-by : 19 µA
Consumption : 4 mA max / 3,6 Vcc
[868 - 868.6] MHz and
[868.7 - 869.2] MHz
100 m -> 300m
Maximum power radio < 10 mW,
receiver category: 2
-10°C / +70°C
-30°C / +60°C
IP IP 55
95%
91,7 x 201,5 x 124,3 mm
730 gr.
Important product
information (❸)