Delta DOP-A series User manual

English
-
1
Preface
Thank you for purchasing DELTA’s DOP-A, AE and AS series. This uick start will be helpful in the
installation, wiring and inspection of Delta HMI. Before using the product, please read this uick start
to ensure correct use. You should thoroughly understand all safety precautions before proceeding
with the installation, wiring and operation. Place this uick start in a safe location for future
reference. Please observe the following precautions:
Install the product in a clean and dry location free from corrosive and inflammable gases or
li uids.
Ensure that all wiring instructions and recommendations are followed.
Ensure that HMI is correctly connected to a ground. The grounding method must comply
with the electrical standard of the country.
Do not modify or remove wiring when power is applied to HMI.
Do not touch the power supply during operation. Otherwise, it may cause electric shock.
For the information of HMI software operation, software installation and hardware wiring,
please refer to the HMI software manual.
If you have any uestions during operation, please contact our local distributors or Delta sales
representative.
The content of this uick start may be revised without prior notice. Please consult our distributors or
download the most updated version at 0H http://www.delta.com.tw/industrialautomation.
Safety Precautions
Carefully note and observe the following safety precautions when receiving, inspecting, installing,
operating, maintaining and troubleshooting. The following words, DANGER, WARNING and STOP are
used to mark safety precautions when using the Delta’s HMI product. Failure to observe these
precautions may void the warranty!
Installation

Comply with uick start for installation. Otherwise it may cause e uipment
damage.
 Do not install the product in a location that is outside the stated specification for
the HMI. Failure to observe this caution may result in electric shock, fire, or
personal injury.
Wiring
 Connect the ground terminals to a class-3 ground (Ground resistance should not
exceed 100Ω). Improper grounding may result in communication error, electric
shock or fire.
Operation
 The users should use Delta Screen Editor software to perform editing in Delta's HMI
product. To perform editing and confirming HMI programs without using Delta
Screen Editor software in Delta's HMI product may result in abnormal operation.

English
-
2

Do not modify wiring during operation. Otherwise it may result in electric shock or
personal injury.
 Never use a hard or pointed object to hit or strike the screen as doing this may
damage the screen and let the screen has not respond at all, and then cause HMI to
work abnormally..
Maintenance and Inspection

Do not touch any internal or exposed parts of the HMI as electrical shock may
result.
 Do not remove operation panel while power is on. Otherwise electrical shock may
result.
 Wait at least 10 minutes after power has been removed before touching any HMI
terminals or performing any wiring and/or inspection as an electrical charge may
still remain in the HMI with hazardous voltages even after power has been
removed.
 Turn the power off before changing backup battery and check system settings after
finishing change. (all data will be cleared after changing battery).
 Be sure the ventilation holes are not obstructed during operation. Otherwise
malfunction may result due to bad ventilation or overheating troubles.
Wiring Method

Remove the terminal block from the HMI before wiring.
 Insert only one wire into one terminal on the terminal block.
 If the wiring is in error, perform the wiring again with proper tools. Never use force
to remove the terminals or wires. Otherwise, it may result in malfunction or
damage.
 For the power line that forced to take out, ensure to check wiring again and restart.
Communication Wiring
 Comply with communication wiring specification for wiring.
 Wiring length should comply with the stated specification for the HMI.
 Proper grounding to avoid bad communication uality.
Installation and Storage Conditions
The product should be kept in the shipping carton before installation. In order to retain the warranty
coverage, the HMI should be stored properly when it is not to be used for an extended period of time.
Some storage suggestions are:
Store in a clean and dry location free from direct sunlight.
Store within an ambient temperature range of -20°C to +60°C (-4°F to 140°F).
Store within a relative humidity range of 10% to 90% and non-condensing.
Do not store the HMI in a place subjected to corrosive gases and li uids.
Correctly packaged and placed on a solid and durable surface.
Do not mount the HMI adjacent to heat-radiating elements or in direct sunlight.
Do not mount the HMI in a location subjected to corrosive gases, li uids, or airborne dust
or metallic particles.
Do not mount the HMI in a location where temperatures and humidity will exceed
specification.
Do not mount the HMI in a location where vibration and shock will exceed specification.
Do not mount the HMI in a location where it will be subjected to high levels of
electromagnetic radiation.

English
-
3
Installation
Installation Note:
Improper installation will result in malfunction and greatly reduce the life of the HMI. Be
sure to follow the guidelines in this uick start when installing the HMI.
In order to ensure the HMI being well ventilated, make sure that the ventilation holes are
not obstructed and must provide sufficient free space around HMI.
For use on a flat surface of a Type 4X "Indoor Use Only" enclosure or e uivalent.
Installation Method [A and AE Series]:
Step 1:
Ensure to put waterproof gasket into HMI and
then insert the HMI into the panel cutout.
Step 2:
Ensure to insert fasteners into the HMI’s insertion
slots and turn the screw till screws touch panel
cutout.
Step 3:
Turn the screw with less than tor ue 0.7N-M to avoid damage to plastic box. Tor ue:
6.17lb-inch(0.7N-M)
Installation Method [AS Series]:
Step 1:
Ensure to put waterproof gasket into HMI and
then insert the HMI into the panel cutout.
Step 2:
Ensure to insert fasteners into the HMI’s insertion
slots and turn the screw till screws touch panel
cutout.

English
-
4
Step 3:
Turn the screw with less than tor ue 0.7N-M to avoid damage to plastic box. Tor ue:
6.17lb-inch(0.7N-M)
Power Line Installation
The specifications for power terminal wiring are shown in the table below:
Type Wire Gauge (AWG) Stripped length Tor ue
Solid 28~12 7~8 mm 5 kg-cm (4.3 lb-in)
Stranded 28~12 7~8 mm 5 kg-cm (4.3 lb-in)
The specifications for communication terminal wiring are shown in the table below (AS Series only):
Type Wire Gauge (AWG) Stripped length Tor ue
Solid 30 ~ 16 5 ~ 6 mm 2 kg-cm (1.7 lb-in)
Stranded 30 ~ 16 5 ~ 6 mm 2 kg-cm (1.7 lb-in)
Be sure to plug power line into HMI according to following arrow direction.
DOP
-
A80THTD1
DOP-AE80THTD
DOP-A(E)10THTD1
DOP
-
AS35THTD
DOP-AS38BSTD
DOP-AS57BSTD

English
-
5
Basic Inspection
Item Content
General Inspection
Periodically inspect the screws of the connection between the HMI and
device. Tighten screws as necessary as they may loosen due to vibration
and varying temperatures.
Ensure that oil, water, metallic particles or any foreign objects do not fall
inside the HMI, control panel or ventilation slots and holes. As these will
cause damage.
Ensure the correct installation and the control panel. It should be free from
airborne dust, harmful gases or li uids.
Inspection before
operation (power is
not applied)
Ensure that all wiring terminals are correctly insulated.
Ensure that all wiring is correct or damage and or malfunction may result.
Visually check to ensure that there are not any unused screws, metal
strips, any conductive or inflammable materials inside HMI.
Ensure to lower electromagnetic interference when devices are influenced
by it.
Ensure that the external applied voltage to HMI is correct and matched to
the controller.
Inspection before
operation (power is
applied)
Check if power LED lights.
Check if the communication among devices is normal.
Please contact our local distributors or Delta sales representative if there
are any abnormal conditions.
Pin Definition of Serial Communication
COM1 Port A, AE and AS57BSTD Series]
COM Port PIN Contact
RS-232
1
2 RXD
3 TXD
4
5 GND
6
7 RTS
8 CTS
9
Note: Blank = No Connection.
Pin

English
-
6
COM2 Port A Series]
COM Port PIN MODE1 MODE2 MODE3
RS-232 RS-422 RS-485
1 RXD- D-
2 RXD RXD+ D+
3 TXD TXD+ D+
4 TXD- D-
5 GND
6 RTS-
7 RTS RTS+
8 CTS CTS+
9 CTS-
Note 1: Blank = No Connection.
Note 2: When selecting Mode3 (for RS-485), D+ indicates that PIN 2 and PIN 3 is connected,
and D- indicates that PIN 1 and PIN 4 is connected.
COM2 and COM3 Port AE, A80THTD1 and A10THTD1 Series]
COM Port PIN
MODE1
MODE2
MODE3
MODE4
MODE5
MODE6
RS-232
RS-422
RS-485
RS-232*
2
RS-422*
2
RS-485*
2
COM2
1 RXD-
D- RXD1-
D1-
2 RXD RXD+
D+ RXD1
RXD1+
D1+
3 TXD TXD+
D+ TXD1
TXD1+
D1+
4 TXD-
D- TXD1-
D1-
5 GND
COM3
6 RTS-
TXD2-
D2-
7 RTS RTS+
TXD2
TXD2+
D2+
8 CTS CTS+
RXD2
RXD2+
D2+
9 CTS-
RXD2-
D2-
Note 1: Blank = No Connection.
Note 2: When selecting Mode3 (for RS-485), D+ indicates that PIN 2 and PIN 3 is connected,
and D- indicates that PIN 1 and PIN 4 is connected. When selecting Mode6 (for
RS-485), D1+ indicates that PIN 2 and PIN 3 is connected, D1- indicates that PIN 1
and PIN 4 is connected, D2+ indicates that PIN 7 and PIN 8 is connected, and D2-
indicates that PIN 6 and PIN 9 is connected.
COM1 and COM3 AS38BSTD, AS35THTD Series]
COM Port PIN MODE1 MODE2
RS-232 RS-232*2
COM1
1
2 RXD RXD1
3 TXD TXD1
4
5 GND
COM3
6
7 RTS TXD2
8 CTS RXD2
9
Note: Blank = No Connection.
Pin
Pin
Pin

English
-
7
COM2 Port AS38BSTD, AS35THTD Series]
COM Port PIN MODE1 MODE2
RS-422 RS-485
R- RXD- D-
R+ RXD+ D+
T- TXD- D-
T+ TXD+ D+
G GND
Note 1: When selecting Mode2 (for RS-485), D+ indicates that R+ and T+ is connected, and
D- indicates that R- and T- is connected.
COM2 and COM3 Port AS57BSTD Series]
COM Port PIN MODE1 MODE2 MODE3
RS-485*2
RS-422*2
RS-422
COM2
R- D- RXD- RXD-
R+ D+ RXD+ RXD+
T- TXD- TXD-
T+ TXD+ TXD+
G GND
COM3
R- D- RXD- CTS-
R+ D+ RXD+ CTS+
T- TXD- RTS-
T+ TXD+ RTS+
Note 1: Blank = No Connection.
Note 2: When using RS-422 flow control, please refer to the COM3 Port signals table above
for pin assignments. At this time, COM2 and COM3 ports cannot be used individually.
Comparison of Flow Control Protocols
COM
Port
DOP-AE Series DOP-A Series
DOP-AS57 Series DOP-AS35 / AS38
Series
COM1
RS-232 flow control
supported
RS-232 flow
control
supported
RS-232 flow control
supported
RS-232 flow control
supported. But, when
RS-232 flow control
function is enabled,
COM3 can not be used.
COM2
RS-422 flow control
supported. But,
when RS-422 flow
control function is
enabled, COM3 can
not be used.
RS-422 flow
control
supported
RS-422 flow control
supported. But, when
RS-422 flow control
function is enabled,
COM3 can not be
used.
RS-422 flow control is
not supported.
COM3
N/A
RS-232 flow control
supported. But, when
RS-232 flow control
function is enabled,
COM3 can not be used.
Note: For more detailed information regarding the pin definition for flow control, please refer
to the pin definition of serial communication of each series.
COM2
COM3
R
-

English
-
8
Dimensions
DOP-AS35THTD / DOP-AS38BSTD
118.8
+0.04+1
(4.68 )
140.8
104.8
0 0
(3.65 ) T=1.6mm(0.06in) ~
92.8
0
+1
3.0mm(0.12in)
NOTE:
0
+0.04
T
4-R3 36.7
DOP-AS57BSTD
0.12in(3.0mm)
T=0.06in(1.6mm) ~
(5.21 )
+1
0 +0.04
0
(6.79 )
0
+1 +0.04
0
144.1(5.67)
184.1(7.25)
6.1(0.24)39.0(1.54)
172.4
132.4
4-R3(0.12)
T
NOTE:
Units: mm
Units: mm

English
-
9
DOP-A80THTD1 / DOP-AE80THTD
T=1.6mm(0.06in) ~
3.0mm(0.12in)
(1.75)
178.1(7.01)
243.1(9.57)
0
+1
231.4
0
(9.11 )
+0.04
+0.04
(6.55 )
0
+1
166.4
0
NOTE:
4-R3.0(0.12)
44.4
T
6.1(0.24)
DOP-A(E)10THTD1
3.0mm(0.12in)
+0.04
(11.22 )
+1
0 0
T=1.6mm(0.06in) ~
(8.27 )
+1
0 +0.04
0
210.2
285.2
4-R3.0(0.12)
NOTE:
T
297.1(11.70)
222.1(8.74)
43.1(1.70) 6.1(0.24)
Units: mm
Units: mm