Delta VFB080D4LED1 User manual

MODEL VFB080D4LED1
P
a
g
e 1.
INSTALLATION AND OPERATING INSTRUCTIONS
FAN / LED LIGHT / LED NIGHT LIGHT
READ AND SAVE THESE INSTRUCTIONS
GENERAL SAFETY INFORMATION
1. Make sure that the electric service supply voltage is AC
120V, 60Hz.
2. Follow all local electrical and safety codes, as well as the
Nation Electrical Code (NEC) and the Occupation Safety
and Healthy Act (OSHA).
3. Always disconnect the power source before working on or
near the ventilating fan, motor or junction box.
4. Protect the power cord from sharp edges, oil, grease, hot
surfaces, chemicals or other objects.
5. Do not kink the power cord.
6. Do not install the unit where ducts are configured as shown
in Fig. A.
7. Provide suction parts with proper ventilation.
8. This unit is UL listed for use over a bathtub or shower
when installed in a GFCI protected branch circuit.
9. These ventilating fans are intended for residential usage
only.
10. Do not install this ventilating fan where air temperature
may exceed 40°C (104°F).
Turning angle too large Duct shrink
Too many elbows Elbow near the body
Body
Fig. A
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
2. Before servicing or cleaning unit, switch power off at
service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the
service panel.
3. Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction.
4. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
of Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE) and local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted ventilating fan must always be vented to the
outdoors.
7. If this unit is to be installed over a tub or shower, it must be
marked as appropriate for the application and be connected
to a GFCI (Ground Fault Circuit Interrupter) – protected
branch circuit.
8. Do not use this unit with any other solid-state control
device. Solid-state controls may cause harmonic distortion,
which can cause motor humming noise.
9. NEVER place a switch where it can be reached from a tub
or shower.
10. Not to be installed in a ceiling thermally insulated to a
value greater than R40. (This is required for installation in
Canada only)
11. Do not open/disassemble the LED light engine or tear off
the warranty label for protect the life and performance.
CAUTION
1. To reduce the risk of electric shock, please disconnect the
electrical supply circuit to the fan before installing light kit.
2. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
3. Not for use in cooking area. (Fig. B)
4. This product must be properly connect to the grounding
conductor of the supply circuit.
Cooking area
Fig. B

MODEL VFB080D4LED1
P
a
g
e 2.
SUPPLIED ACCESSORIES
Part name Appearance Quantity
Grille
(Include LED
Light Engine)
1
Long Screw
(M4×25) 6
Screw
(M4×12) 3
Suspension
bracketⅠ
(6.10 inch) 1
Suspension
bracketⅡ
(11.81 inch) 1
Suspension
bracketⅢ
(13.98 inch)
1
INSTALLATIONS
A. Install with wood frame
Model No. VFB080D4LED1
Install Dim. (in.) 10.2 ╳10.2
1. Body installation
1-1. Construct the wood frame(not provided) with 30mm square
bar and attach it to the ceiling joist.
1-2. Attach the duct connector to the wood frame with taping
screw.
1-3. Insert the body into the wood frame and connect it to the
duct connector. Secure the body on wood frame with taping
screws.
B. Install with joist
1. Choose the installation type according to the fig as below:
SpacingA on center joists Insert Suspension bracket Suspension bracket No.
12.0 inch Refer to Fig B-01, B-02 I,II
16.0 inch Refer to Fig B-03, B-04 I,II,III
19.2 inch Refer to Fig B-03, B-04 I,II,III
24.0 inch Refer to Fig B-03, B-04 I,II,III
1-1 TypeⅠ－12 inches between joists
1-1.1 Insert the suspension bracketⅠinto the bracket cover of
adaptor side and select one of suspension bracketⅡof the
back of the fan body.
1-1.2 Insert the fan between joists. Make sure the fan body is
level and perpendicular with the joist.
1-1.3. Ensure the distance between ceiling and fan body for the
thickness of grille.
1-1.4 Secure the all suspension bracket to joists by using
tapping screw on the tab.
1-1.5 Secure the suspension bracket I and II to fan body by
using screw(M4×12-2pce each).
1-2 TypeⅡ－16/19.2/24 inches between joists
B-01
B-02
Suspension Bracket I
Suspension Bracket II
Long Screw(M4×25)
JoistJoist
Joist
Joist
Main Body
Long Screw(M4×25)
12.0
Screw M4×12
Tab
Duct connector
Wood frame
Taping screw
Wood frame

MODEL VFB080D4LED1
P
a
g
e 3.
1-2.1 Insert the suspension bracketⅠinto the bracket cover of
adaptor side and insert the suspension bracketⅡand Ⅲ
into the back of the fan body.
1-2.2 Insert the fan between joists. Make sure the fan body is
level and perpendicular with the joist.
1-2.3 Ensure the distance between ceiling and fan body for the
thickness of grille.
1-2.4 Secure the all suspension bracket to joists by using
tapping screw on the tab.
1-2.5 Secure the suspension bracket I to fan body by using
screw(M4×12).
1-2.6 Secure the suspension bracket to fan body by using
screw(M4×12) between II and III.
2. Duct connection
2-1. Insert the duct into the duct connector and tape all
ductworks connection to make them secure and air tight.
2-2. Install the duct with a gradient 1°~2° to the outside.
3. Connect wiring
3-1. Follow all local electrical and safety codes.
3-2. NEVER place a switch where it can be reached from a tub
or shower.
3-3. Connect wires as shown in wiring diagrams.
3-4. Using wire nuts, connect house power cable to ventilating
fan, light and night light wires.
3-5. 14 AWG (2.1 mm2) is the smallest conductor that shall be
used for branch-circuit wiring.
4. Test run and grille attachment
4-1. Insert the LED light engine power source connect into the
installation location of main body.
4-2. When the power on, check for abnormal vibration or sound.
4-3. Insert the mounting springs into the slots and mount the
grille to the body.
B-04
B-03
Compartment
Power cable
Wire nut
Suspension
Bracket I
Suspension
Bracket II
JoistJoist
Suspension
Bracket III
Joist
Joist
16.0
19.2
24.0
Screw M4×12
Tab
Tab
Outside
Inside
Duct
Foil Tape
Body
Grille
Ceiling
Inspection Hole
Gradient 1°~2°

MODEL VFB080D4LED1
P
a
g
e 4.
5. Operation
Model: VFB080D4LED1
Turn on/off the power to operate fan / light / night light
on/off.
MAINTENANCE
WARNING:
Disconnect power source before working on unit. Routine
maintenance must be done every year.
CAUTION:
1. Never use gasoline, benzene, thinner or any other such
chemicals for cleaning the ventilating fan.
2. Do not allow water to enter motor.
3. Do not soak resin parts in water over 60°C.
CLEANING：
1. Remove the LED light engine from grille module carefully.
Disassemble the light power connections to remove grille.
2. Wash and clean grille. CAUTION: Do not let water into the
LED light engine. (Use non-abrasive kitchen detergent,
wipe dry with a new cloth.)
3. Remove dust and dirt from ventilating fan using a cleaner.
4. Replace grille.
DIMENSION
SPECIFICATIONS-VENTOLATION FAN
Model No. Voltage
(V) Frequency (Hz) Power (W) Air Flow @ 0.1SP (CFM) Weight (lb.) Note
VFB080D4LED1 120 60 25 80 8LED Light
/ LED Night
Light
SPECIFICATIONS-LED LIGHT ENGINE
（AT FULL LIGHT OUTOUT）
ITEM SPEC.
DIMENSION（INCH）8L×4.4W×1.4H
POWER CONSUMPTION（W）16
CORRELATED COLOR TEMPERATURE (K) 4000
LIGHT SOURCE LIFE （HOURS）25000（MIN.）
TRANSIENT PROTECTION CLASS A
OPERATING FREQUENCY（HZ）120
FCC QUALIFIED YES
ENERGY QUALIFIED YES
ROHS QUALIFIED YES
SAFETY REQUIREMENTS UL/cUL
WARRANTY
DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY
Delta Electronics Inc.(“Delta Electronics”) warrants to the original consumer purchaser in the USA
that the Breez ventilation fan products will be free from defects in material or workmanship. This
warranty is limited to three (3) years from the original date of purchase.
Limitations and Exclusions
1. During the warranty period, a replacement for any defective product will be supplied free of charge
for installation by the consumer. The warranty provided herein does not cover charges for labor or
other costs incurred in the troubleshooting, repair, removal, and installation service.
2. All returns of defective parts or products must include the product model number, and must be
made through an authorized Delta Electronics distributor. Authorized returns must be shipped
prepaid. Repaired or replacement products will be shipped by Delta Electronics F.O.B. shipping
point.
3. Delta Electronics shall not be liable for any indirect, incidental, consequential, punitive, or special
damages arising out of or in connection with products use or performance, regardless of the form of
action whether in contract, tort (including negligence), strict product liability or otherwise.
4. This warranty does not extend to fluorescent lamp starters and tubes.
5. The warranty does not cover if user does not comply with manufacture’s installation manual.
6. To qualify for warranty service, you must notify Delta Electronics at the address or telephone
number below.
7. Delta Electronics shall have no liability to the original owner-user with respect to any defect caused
by abuse, misuse, neglect, improper transportation or storage, improper testing, improper installation,
improper operation, improper use, improper maintenance, improper repair, improper alteration,
improper modification, tampering or accident of products or parts thereof, or unusual deterioration or
degradation of products or parts thereof due to a physical environment beyond the requirements of
products’ specifications.
Address: 4405 Cushing Parkway, Fremont, CA94538
US Toll Free Number: 1-888-979-9889
Grille
Slots
Spring
LED Light
Power Connect