Delta DVS-103I02C-DLR User manual

www.deltaww.com
EtherNet/IP DLR
Industrial Ethernet Switches
DVS-103I02C-DLR
Operation Manual

Industrial Automation Headquarters
Delta Electronics, Inc.
Taoyuan Technology Center
No.18, Xinglong Rd., Taoyuan District,
Taoyuan City 33068, Taiwan
TEL: [phone] / FAX: [phone]
Asia
Delta Electronics (Shanghai) Co., Ltd.
No.182 Minyu Rd., Pudong Shanghai, P.R.C.
Post code : 201209
TEL: [phone] / FAX: [phone]
Customer Service: 400-820-9595
Delta Electronics (Japan), Inc.
Tokyo O󰀩ce
Industrial Automation Sales Department
2-1-14 Shibadaimon, Minato-ku
Tokyo, Japan 105-0012
TEL: [phone] / FAX: [phone]
Delta Electronics (Korea), Inc.
Seoul O󰀩ce
1511, 219, Gasan Digital 1-Ro., Geumcheon-gu,
Seoul, 08501 South Korea
TEL: [phone] / FAX: [phone]
Delta Energy Systems (Singapore) Pte Ltd.
4 Kaki Bukit Avenue 1, #05-04, Singapore 417939
TEL: [phone] / FAX: [phone]
Delta Electronics (India) Pvt. Ltd.
Plot No.43, Sector 35, HSIIDC Gurgaon,
PIN 122001, Haryana, India
TEL: [phone] / FAX : [phone]
Delta Electronics (Thailand) PCL.
909 Soi 9, Moo 4, Bangpoo Industrial Estate (E.P.Z),
Pattana 1 Rd., T.Phraksa, A.Muang,
Samutprakarn 10280, Thailand
TEL: [phone] / FAX : [phone]
Delta Energy Systems (Australia) Pty Ltd.
Unit 20-21/45 Normanby Rd., Notting Hill Vic 3168,Australia
TEL: [phone]
Americas
Delta Electronics (Americas) Ltd.
Raleigh O󰀩ce
P.O. Box 12173, 5101 Davis Drive,
Research Triangle Park, NC 27709, U.S.A.
TEL: [phone] / FAX: [phone]
Delta Greentech (Brasil) S/A
São Paulo O󰀩ce
Rua Itapeva, 26 – 3˚ Andar - Bela Vista
CEP: 01332-000 – São Paulo – SP - Brasil
TEL: [phone]
Delta Electronics International Mexico S.A. de C.V.
Mexico O󰀩ce
Vía Dr. Gustavo Baz No. 2160, Colonia La Loma,
54060 Tlalnepantla Estado de Mexico
TEL: [phone] #3050/3052
*We reserve the right to change the information in this catalogue without prior notice.
EMEA
Headquarters: Delta Electronics (Netherlands) B.V.
Sales: [e-mail]
Marketing: [e-mail]
Technical Support: [e-mail]
Customer Support: [e-mail]
Service: [e-mail]
TEL: [phone]
BENELUX: Delta Electronics (Netherlands) B.V.
De Witbogt 20,5652 AG Eindhoven,The Netherlands
Mail: [e-mail]
TEL: [phone]
DACH: Delta Electronics (Netherlands) B.V.
Coesterweg 45,D-59494 Soest,Germany
Mail: [e-mail]
TEL: [phone]
France: Delta Electronics (France) S.A.
ZI du bois Challand 2,15 rue des Pyrénées,
Lisses, 91090 Evry Cedex, France
Mail: [e-mail]
TEL: [phone]
Iberia: Delta Electronics Solutions (Spain) S.L.U
Ctra. De Villaverde a Vallecas, 265 1º Dcha Ed.
Hormigueras – P.I. de Vallecas 28031 Madrid
TEL: [phone]
Carrer Llacuna 166, 08018 Barcelona, Spain
Mail: [e-mail]
Italy: Delta Electronics (Italy) S.r.l.
U󰀩cio di Milano Via Senigallia 18/2 20161 Milano (MI)
Piazza Grazioli 18 00186 Roma Italy
Mail: [e-mail]
TEL: [phone]
Russia: Delta Energy System LLC
Vereyskaya Plaza II, o󰀩ce 112 Vereyskaya str.
17 121357 Moscow Russia
Mail: [e-mail]
TEL: [phone]
Turkey: Delta Greentech Elektronik San. Ltd. Sti. (Turkey)
Şerifali Mah. Hendem Cad. Kule Sok. No:16-A
34775 Ümraniye – İstanbul
Mail: [e-mail]
TEL: + 90 216 499 9910
GCC: Delta Energy Systems AG (Dubai BR)
P.O. Box 185668, Gate 7, 3rd Floor, Hamarain Centre
Dubai, United Arab Emirates
Mail: [e-mail]
TEL: [phone]
Egypt + North Africa: Delta Electronics
511 Cairo Business Plaza, North 90 street,
New Cairo, Cairo, Egypt
Mail: [e-mail]
DVS-022BA20-01
2019/11/30

EtherNet/IP DLR Industrial Ethernet Switches
DVS-103I02C-DLR Operation Manual
Revision History
Version
Revision
Date
1
st
The first version was published.
2019/12/18

i
EtherNet/IP DLR Industrial Ethernet Switches
DVS-103I02C-DLR Operation Manual
Table of Contents
Chapter 1 Introduction
1.1 Introduction ......................................................................................1-2
1.2 General Specification.........................................................................1-3
1.3 Functional Specification.....................................................................1-4
1.4 Communication Interface Specification .............................................1-4
1.4.1 Ethernet/IP ....................................................................................1-4
1.5 Power, Weight and Electric Specification...........................................1-4
1.6 Dimensions and parts descriptions....................................................1-5
1.7 Pin Definition and Wiring...................................................................1-6
1.8 Installation........................................................................................1-8
1.9 Network Topology .............................................................................1-9
Chapter 2 Software Configuratio
2.1 Software Configuration......................................................................2-2
2.1.1 Software description........................................................................2-2
2.1.2 Procedures.....................................................................................2-2
2.2 Parameter Settings............................................................................2-4
2.2.1 Device Parameters..........................................................................2-4
2.2.1.1 Ring Status..................................................................................2-5
2.2.1.2 Port 1, Port 2, and Device Port........................................................2-6
2.2.1.3 Alarm..........................................................................................2-6
2.2.2 EIP Parameters ..............................................................................2-7
2.2.2.1 Module Status ..............................................................................2-7
2.2.2.2 IP Setting ....................................................................................2-7
2.2.2.3 Connection ..................................................................................2-8
2.2.2.4 Port Status ..................................................................................2-8
2.2.2.5 DLR ............................................................................................2-8

ii
Chapter 3 Operation on the Web
3.1 Overview........................................................................................... 3-2
3.2 Getting Started..................................................................................3-2
3.2.1 Exploring the webpage.................................................................. 3-2
3.2.2 Using the Webpage....................................................................... 3-3
3.2.3 Login .......................................................................................... 3-4
3.2.4 Menu.......................................................................................... 3-5
3.3 Information.......................................................................................3-6
3.3.1 Device Information ....................................................................... 3-6
3.4 Network Configuration ......................................................................3-7
3.4.1 Account Management.................................................................... 3-7
3.4.2 Firmware Update.........................................................................3-10
3.5 EtherNet/IP DLR Status .................................................................. 3-10
3.6 Save Configuration.......................................................................... 3-12
Chapter 4 Troubleshooting
4.1 Troubleshooting................................................................................4-2
4.1.1 Clear the Error States ................................................................... 4-2
4.1.2 DLR Status Indicator..................................................................... 4-2
4.1.3 Alarm Status Indicators................................................................. 4-2

1-1
Chapter 1 Introduction
Table of Contents
1.1 Introduction....................................................................1-2
1.2 General Specification ......................................................1-3
1.3 Functional Specification ..................................................1-4
1.4 Communication Interface Specification...........................1-4
1.4.1 Ethernet/IP....................................................................................1-4
1.5 Power, Weight and Electric Specification ........................1-4
1.6 Dimensions and parts descriptions..................................1-5
1.7 Pin Definition and Wiring ................................................1-6
1.8 Installation .....................................................................1-8
1.9 Network Topology...........................................................1-9
1
1

DVS-103I02C-DLR Operation Manual
1-2
_1
1.1 Introduction
Thank you for choosing Delta DVS-103I02C-DLR. Before using the module, please read this manual for proper
installation and operation.
The DVS-103I02C-DLR is an EtherNet/IP DLR Industrial Ethernet Switch, supporting EtherNet/IP Device Level Ring
(DLR). The DLR protocol provides high network availability in various topologies, including ring topology, linear topology,
and start topology. You can use Delta EtherNet/IP communication software, EIP Builder to configure communication
settings through EtherNet/IP network.
DVS-103I02C-DLR features the followings:
1. Supports EtherNet/IP protocol
2. One built-in digital input point and one output point for alarm
3. Redundant power input point
4. Uses external DIP switch to set up IP communications (software, DHCP, BOOTP), restore default values and
enable/disable DLR function
5. Provides DLR indicators, showing the status of the ring topology

1_
Chapter 1 Introduction
1-3
1.2 General Specification
Item Specification
Operation temperature -20°C
~ 70°C
Storage temperature
-40°C ~ 85°C
Operation humidity
5~95%, non-condensing
Storage humidity
5~95%, non-condensing
Operating environment
Corrosive gases do not exist
Installation
Inside a control box
Pollution degree
2
Degree of protection IP40
EMC Standard
(electromagnetic
compatibility)
EMI:
IEC 61000-6-4, EN 55032, AS/NZS CISPR32, FCC 47 CFR, Part 15 Subpart B,
Class A
EMS:
IEC 61000-6-2: 2016
EN 55024: 2010/A1: 2015
IEC 61000-4-2 level 3, IEC 61000-4-3 level 3, IEC 61000-4-4 level 3,
IEC 61000-4-5 level 1, IEC 61000-4-6 level 3, IEC 61000-4-8 level 4
Vibration immunity
Tested with:
5 Hz
≦
f
≦
8.4 Hz, constant amplitude 3.5 mm;
8.4 Hz ≦f ≦150 Hz, constant acceleration 1g
Duration of oscillation: 10 sweep cycles per axis on each direction of the 3
mutually perpendicular axes
International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)
Shock
Tested with:
Half-sine wave: Strength of shock 15 g peak value, 11 ms duration;
Shock direction: The shocks in each direction per axis, on 3 mutually
perpendicular axes (total of 18 shocks)
International standards: IEC 61131-2 & IEC 60068-2-27 (TEST Ea)
Certificates
EN62368-1, UL61010

DVS-103I02C-DLR Operation Manual
1-4
_1
1.3 Functional Specification
Item Specification
Maximum number of Device Level Ring nodes 50
Response time in ring topology
≦3 ms
Ring topology Ring supervisor, ring node
Minimum beacon interval 100 µs
IGMP snooping V1/V2
1.4 Communication Interface Specification
1.4.1 Ethernet/IP
Item Specification
Connector RJ-45
Interface 10/100 Base-T (X), auto MDI/MDI-X (medium dependent interface crossover),
autonegotiate and forced speed / duplex modes
Number of ports 3 (Device port *1, DLR port *2)
Transmission speed 10/100 Mbps
Communication protocol ARP, ICMP, IP, TCP, EtherNet/IP
Communication distance 100 m
Ethernet cable type Category 5e
1.5 Power, Weight and Electric Specification
Item Specification
Power supply voltage 12 ~ 48 VDC
Insulation voltage 500 V
Consumed power 3.7 W
Weight 126 g

1_
Chapter 1 Introduction
1-5
1.6 Dimensions and parts descriptions
3.4
13.5
3
PWR1/PWR2
DLR
DI
A LARM
A CT
LIN K
D V S-103
1
2
110
28
75
1
2
4
1
Unit: mm
No. Name Description
1
PWR 1 LED /
PWR 2 LED
(Green)
Power status indicator
ON: Normal power supply
(as long as any one of the power is normal, the system operates normally)
OFF: No power supply
DLR LED
(Green)
DLR status indicator
OFF: Not in DLR mode
ON: DLR is in operation and ring topology is normal
Blinking (200 ms ON/OFF): DLR is in operation but an error occurs in the ring
topology
DI LED
Digital input status indicator
OFF: No input
ON: Receiving a higher potential input
ALARM LED
Alarm (output) status indicator
OFF: No alarm (no output)
ON: Send out a higher potential output
2
Ethernet
communication port
(RJ45)
Connecting Ethernet cables
Device port: Used for non-DLR connection
Port 1 and 2: Used for DLR network connection

DVS-103I02C-DLR Operation Manual
1-6
_1
No. Name Description
3 Power supply terminal 12~48 VDC power input, digital input and output (alarm)
4 Mode settings
DIP1 & DIP2
OFF / OFF: Use EIP Builder to set up the IP address
ON / OFF: Use BOOTP to set up the IP address
OFF / ON: Use DHCP to set up the IP address
ON / ON: Restore to default values
DIP3 ON: Start DLR supervisor mode
OFF: Use EIP Builder to set up the mode
DIP4 Reserved
1.7 Pin Definition and Wiring
• Power supply terminal block
Diagram Terminal Description
Alarm + (or -) Alarm relay output:
Carry current 2A@24 VDC
Alarm – (or +)
V+ Digital Input: OFF (0~+5 V) / ON (+11~30V)
Max. input current: 6 mA
V-
V1+ Voltage input 1 (12~48 VDC)
0 V 0V
V2+ Voltage input 2 (12~48 VDC)
0 V 0 V
Ground
Ground
Note: Use single-wire cables or two-wire cables in a diameter of 24 AWG ~ 22 AWG and with less than 1 mm
pin-typed terminals. Only use copper conducting wires with a temperature of 85°C.
24-22AWG
< 1mm 8-10mm

1_
Chapter 1 Introduction
1-7
• RJ-45 terminal block
Diagram Terminal no. Definition Description
1 TX+ Transmit data +
2 TX- Transmit data -
3 RX+ Receive data +
4 -- N/C
5 -- N/C
6 RX- Receive data -
7 -- N/C
8 -- N/C

DVS-103I02C-DLR Operation Manual
1-8
_1
1.8 Installation
Locking screw method: Use M4 for direct screws-fittings (see below).
Pull
Pull
Wall Mount
Installing and dismantling the DIN rail: Attach the back trench of the device to the mounting rail in
arrow ①direction and push the device against the rail in arrow ②direction.
To dismantle, first push down the device in arrow ①direction and follow arrow ③direction to
release the device.
Rail
Note: When installing DVS-103I02C-DLR on the Din Rail, it is required to leave a space of 5 cm among devices.
Do not block top or bottom ventilation openings.

1_
Chapter 1 Introduction
1-9
1.9 Network Topology
Linear Topology
Star Topology
Ring Topology
A DLR function is required to create a ring topology. When a switch is needed for the particular topology, the switch
should support the DLR function. If not, the connection might fail.

DVS-103I02C-DLR Operation Manual
1-10
_1
The EtherNet/IP DLR Industrial Ethernet Switch, DVS-103I02C-DLR, supports DLR function. Use the
communication port named port 1 and port 2 to connect DLR network. Use Device port to connect non-DLR
network. For example, using the Device port to connect to the computer used for setting up.

2-1
Chapter 2 Software Configuration
Table of Contents
2.1 Software Configuration ...................................................2-2
2.1.1 Software description......................................................................2-2
2.1.2 Procedures...................................................................................2-2
2.2 Parameter Settings .........................................................2-4
2.2.1 Device Parameters ........................................................................2-4
2.2.1.1 Ring Status..................................................................................2-5
2.2.1.2 Port 1, Port 2, and Device Port.............................................................2-6
2.2.1.3 Alarm..........................................................................................2-6
2.2.2 EIP Parameters.............................................................................2-7
2.2.2.1 Module Status ..............................................................................2-7
2.2.2.2 IP Setting ....................................................................................2-7
2.2.2.3 Connection ..................................................................................2-8
2.2.2.4 Port Status ..................................................................................2-8
2.2.2.5 DLR ............................................................................................2-8
2

DVS-103I02C-DLR Operation Manual
2-2
_ 2
2.1 Software Configuration
2.1.1 Software description
Users must install two basic software – EIP Builder (V1.07 or later) and COMMGR (V1.10 or later) before operating
the modules. The main function of COMMGR is being the medium software between a PC end and a device that
manages communication interface of devices, while EIP Builder is for setting module parameters.
2.1.2 Procedures
Step 1: For communication type, select Ethernet and name the communication as DLR or any other identifiable
name. When setting is complete, you can close COMMGR window, the software continues to work in the
background; you can still see the COMMGR icon shown in the system list.
Step 2: Next, double-click EIP Builder to open the software.
Step 3: Create a new project.

Chapter 2 Software Configuration
2-3
2__
Step 4: Double-click or drag and drop DVS-103I02C-DLR to add the device to the section of Network View.
Step 5: Select on the toolbar to open the Communication Setting window and select the already set driver from
the drop-down list of the COMMGR Driver
You can click Uploader on the toolbar to view DVS-103I02C-DLR parameters on EIP Builder. Click Downloader
on the toolbar to write modified parameters into DVS-103I02C-DLR. Go to webpage to see DVS-103I02C-DLR
firmware version. Refer to Chapter 3 for more details on the webpage.

DVS-103I02C-DLR Operation Manual
2-4
_ 2
2.2 Parameter Settings
Parameter settings include EIP Parameter and Device Parameter. You need to be in On-Line mode to edit and view
the EIP parameters.
2.2.1 Device Parameters
Click “All Parameters” under the Device Parameter tab, you can see all parameters and status of the device.
You can use the functional icons including Uploader, Downloader , Set to Default ,
Import and Export on the Device Parameter window to upload, download, export, import the device the
device parameters or restore to default values.

Chapter 2 Software Configuration
2-5
2__
2.2.1.1 Ring Status
Click “Ring Status” under the Device Parameter tab, you can see all parameters of the ring topology.
Name Description
Network Topology
Current network topology
1. Linear
2. Ring
Network Status
Current network status
1. Normal
2. Ring fault
Ring Supervisor
Status
If the device is the Ring Supervisor
1. Backup ring supervisor
2. Active ring supervisor
3. Ring node
4. Non-DLR topology
5. Beacon interval or Beacon timeout value not support
Ring Faults Count Number of times that ring fault occurred
Ring Protocol
Participants Count
Number of the devices on the ring topology
Active Supervisor
Precedence
Active supervisor owns high priority