Delta UPS602N2004N035 User manual

www.deltapowersolutions.com
Delta UPS - Amplon Family
User Manual
The power behind competitiveness
N Series, Single Phase
6/ 10 kVA
ON OFF
SETUP

II
Amplon N Series
Save This Manual
This manual contains important instructions and warnings that you should
follow during the installation, operation, storage and maintenance of this
product. Failure to heed these instructions and warnings will void the warranty.
Copyright © 2016 by Delta Electronics Inc. All Rights Reserved. All rights of this
User Manual (“Manual”), including but not limited to the contents, information,
and figures are solely owned and reserved by Delta Electronics Inc. (“Delta”).
The Manual can only be applied to the operation or the use of this product. Any
disposition, duplication, dissemination, reproduction, modification, translation,
extraction, or usage of this Manual in whole or in part is prohibited without the prior
written permission of Delta. Given that Delta will continuously improve and develop
the product, changes may be made to the information in this Manual at any time
without obligation to notify any person of such revision or changes. Delta will make
all possible efforts to secure the accuracy and the integrity of this Manual. Delta
disclaims any kinds or forms of warranty, guarantee, or undertaking, either expressly
or implicitly, including but not limited to the completeness, faultlessness, accuracy,
QRQLQIULQJHPHQWPHUFKDQWDELOLW\RU¿WQHVVIRUDSDUWLFXODUSXUSRVHRIWKH0DQXDO

Table of Contents
III
Table of Contents
Chapter 1:Important Safety Instructions--------------------------- 1
1.1 Safety Instructions ---------------------------------------------- 1
1.2 Standard Compliance ------------------------------------------ 4
1.3 Storage------------------------------------------------------------- 4
Chapter 2:Introduction --------------------------------------------------- 5
2.1 General Overview----------------------------------------------- 5
2.2 Exterior & Dimensions ----------------------------------------- 5
2.3 Package List------------------------------------------------------ 6
Chapter 3:Operation Panel---------------------------------------------- 9
3.1 LED Indicators --------------------------------------------------- 9
3.2 Multi-function Buttons -----------------------------------------10
3.3 LCD Display -----------------------------------------------------13
3.4 7-Segment Display---------------------------------------------15
3.5 16-Segment Display-------------------------------------------17
3.6 Error Code Information----------------------------------------18
3.7 LCD Display Flow Chart--------------------------------------19
Chapter 4:Rear Panel ----------------------------------------------------21
Chapter 5:Wiring ----------------------------------------------------------27
5.1 Pre-wiring Warnings -------------------------------------------27
5.2 Input/ Output Wiring -------------------------------------------28
5.3 External Battery Pack Connection -------------------------30
Chapter 6:Operation Modes -------------------------------------------34
6.1 Standby Mode---------------------------------------------------34
6.2 On-line Mode----------------------------------------------------34
6.3 Bypass Mode----------------------------------------------------34
6.4 Battery Mode ----------------------------------------------------35

IV
Amplon N Series
6.5 ECO Mode -------------------------------------------------------35
6.6 Setup Mode------------------------------------------------------35
Chapter 7:Turn-on & Turn-off Procedures------------------------39
7.1 Turn-on Procedures--------------------------------------------39
7.2 Turn-off Procedures--------------------------------------------40
Chapter 8:Alarm -----------------------------------------------------------41
Chapter 9:Optional Accessories-------------------------------------42
Chapter 10:Troubleshooting ------------------------------------------44
Chapter 11:Maintenance------------------------------------------------47
11.1 UPS----------------------------------------------------------------47
11.2 Batteries ----------------------------------------------------------47
11.3 Fans ---------------------------------------------------------------48
$SSHQGL[7HFKQLFDO6SHFL¿FDWLRQV-------------------------------49
Appendix 2:Warranty ----------------------------------------------------51

Chapter 1 Important Safety Instructions
1
Chapter 1:Important Safety Instructions
1.1 Safety Instructions
Installation Warnings

zBefore installation and usage, please read this User Manual thoroughly. This
helps you to use the product correctly and safely.

zInstall the UPS in a well-ventilated area, away from excess moisture, heat, dust,
ÀDPPDEOHJDVRUH[SORVLYHV

z7RDYRLG¿UHDFFLGHQWVDQGHOHFWULFVKRFNSOHDVHLQVWDOOWKH836LQDWHPSHUDWH
and humidity well-controlled indoor area that is free of conductive contaminants.
For the temperature and humidity specifications, please refer to Appendix 1:
7HFKQLFDO6SHFL¿FDWLRQV.

zLeave adequate space (at least 50cm) around all sides of the UPS for proper
ventilation.
Connection Warnings

zThe UPS must be well grounded due to a possible risk of current leakage.

zThe installation of upstream and downstream protective devices is highly recom-
mended when the UPS is connected to the mains and the loads.

zThe protective devices connecting to the UPS must be installed near the UPS
and must be easily accessible for operation.

zIf you need to move the UPS or perform re-wiring, please turn off the AC input
power and ensure that the UPS has been safely shutdown and the connected
external battery pack has been disconnected. Otherwise, the output end might
still be energized, which might cause electric shock.
Usage Warnings

zThis is a class-A product. In a domestic environment, this product may cause ra-
dio interference, in which case, the user is required to take adequate measures.

zThe UPS can be used to power computers and associated peripheral devices,
such as monitors, modems, cartridge tape drives, external hard drives, etc.

2
Amplon N Series

zIt is strictly forbidden to connect the UPS with:
1. any regenerative-type loads.
 DQ\DV\PPHWULFDOORDGVH[KDOIZDYHUHFWL¿HU

zTo ensure reliable operation of the UPS and to protect the UPS from overheat-
ing, the slits and openings in the UPS must not be blocked or covered.

zBefore usage, you must allow the UPS to adjust to room temperature for at least
one hour to avoid moisture condensing inside the UPS.

zDo not pour and splash any liquid on the UPS. Do not insert any object into
the UPS’s slits and openings. Do not put beverage containers on or around the
UPS.

zWhen an emergency occurs, press the OFF button and release the button after
you hear one beep to turn off the UPS. Cut off the input power to completely
shut down the UPS.

zDo not use any cleaning liquid or spray to clean the UPS. Before cleaning,
please make sure that the UPS has been completely shut down, and the con-
nection between the UPS and the input power and the connection between the
UPS and the external battery pack have been entirely cut off.

z$OOPDLQWHQDQFHVHUYLFHVPXVWEHSHUIRUPHGE\TXDOL¿HGVHUYLFHSHUVRQQHO)RU-
bid opening or removing the cover of the UPS by yourself to avoid high voltage
electric shock.

z<RXPXVWFRQWDFWTXDOL¿HGVHUYLFHSHUVRQQHOLIHLWKHURIWKHIROORZLQJHYHQWVRF-
cur:
1. Liquid is poured or splashed on the UPS.
2. The UPS does not run normally after this 8VHU0DQXDO is carefully observed.
NOTE:
If you use the UPS in an area that generates or incurs dust, you should
LQVWDOODGXVW¿OWHULQWKH836WRHQVXUHQRUPDOSURGXFWOLIHDQGIXQFWLRQ
Battery Warnings

zServicing of batteries or battery packs must be performed or supervised by
qualified service personnel knowledgeable in batteries, battery packs and the
required precautions. Keep unauthorized personnel away from batteries and
battery packs.

Chapter 1 Important Safety Instructions
3

zThe risk of electric shock and short-circuit current is possible when the batteries
and battery packs are connected to the UPS. Before maintenance, disconnect
all batteries and battery packs to cut off the battery power.

zFor battery replacement, only use the same number and type of batteries.

zObserve the following before replacing the batteries:
1. Remove watches, rings, or other metal objects.
2. Use tools with insulated handles.
3. Wear rubber gloves and boots.
4. Do not lay tools or metal parts on the top of batteries.
5. Before battery removal, replacement or installation, disconnect any circuit
connected to the batteries.

z'RQRWFRQQHFWWKHEDWWHULHVLQUHYHUVHRWKHUZLVHDULVNRIHOHFWULFVKRFNRU¿UH
accidents might occur.

zA loss of battery charge capacity may occur during shipping and storage. Before
1st use of the UPS, please fully charge the batteries until the Battery Level Bar
Graph shown on the UPS’s LCD is fully on.

zIf the UPS needs to be stored for an extended period of time, idle batteries
must be fully charged every three months. When every time you charge the idle
batteries, please charge them until the Battery Level Bar Graph shown on the
UPS’s LCD is fully on.
WARNING:
1. The risk of electric shock and short-circuit current is possible when
the batteries are still connected to the UPS even though the UPS
is disconnected from the mains. Do not forget to cut off the battery
source before maintenance.
2. When connecting the external battery pack with the UPS, you must
install an appropriate non-fuse DC breaker or the fast-acting fuse that
PHHWVWKHVDIHW\FHUWL¿FDWLRQ'RQRWXVHDQ$&EUHDNHU
3. The breaker must be a 2-pole non-fuse DC breaker with characteristics
of 1-pole 250Vdc, 2-pole 500Vdc and 35kA (or above) DC breaking
capacity.

4
Amplon N Series
1.2 Standard Compliance

zCE

zEN 62040-1

zEN 62040-2 Category C2
1.3 Storage

zPrior to installation
If the UPS needs to be stored prior to installation, it should be placed in a dry
area. The allowable storage temperature is between -15°C and +50°C.

zAfter usage
Press the OFF button for 3 seconds and release it after you hear a beep, make
sure that the UPS has been completely shut down, disconnect the UPS from
the utility power, remove all loads from the UPS, and store the UPS in a dry and
well-ventilated area at a temperature between -15°C and +50°C. Idle batteries
must be recharged fully every three months if the UPS needs to be stored for
an extended period of time. When every time you charge the batteries, please
charge them until the Battery Level Bar Graph shown on the UPS’s LCD is
fully on.
NOTE:
After storage and before start-up of the UPS, you must allow the UPS to
adjust to room temperature (20°C~25°C) for at least one hour to avoid
moisture condensing inside the UPS.

Chapter 2 Introduction
5
Chapter 2:Introduction
2.1 General Overview
The N series UPS is a single-phase on-line UPS providing reliable and consistent
sine-wave quality power to your electronic equipment. It adopts the latest technol-
ogy and the highest quality components providing output power factor up to unity,
DQGLWVHI¿FLHQF\LQRQOLQHPRGHFDQUHDFKDWPD[LPXP7KH836QRWRQO\
provides safe, reliable and uninterrupted power to your sensitive electronic equip-
PHQWDWDOOWLPHVEXWDOVRSURGXFHVJUHDWHUHOHFWURQLFSRZHUHI¿FLHQF\DWOHVVFRVW
Its compact design does not occupy much space and is easy to use. There are two
different ratings, 6kVA and 10kVA, for your selection.
2.2 Exterior & Dimensions
)LJXUHN9$N9$([WHULRU'LPHQVLRQV
325mm
390mm
190mm
ON OFF
SETUP

6
Amplon N Series
2.3 Package List

zFor models UPS602N2004N035 (6 kVA ) & UPS103N2004N035 (10 kVA )
1 2
www.deltapowersolutions.com
Delta UPS - Amplon Family
User Manual
The power behind competitiveness
N Series, Single Phase
6/ 10 kVA
ONOFF
SETUP
ON OFF
SETUP
3
456
7
8
9
10
x 3 x 4
x 2 x 6
No. Item Q’ty
1UPS 1 PC
2Parallel Cable 1 PC
3User Manual 1 PC
4Battery Cable 1 PC
5CU Terminal_ Type A 3 PCS
6CU Terminal_ Type B 4 PCS
7Battery Cable Holder 1 PC
8Screw for Battery Cable Holder 2 PCS
9USB Cable 1 PC
10
Cable Tie 6 PCS

Chapter 2 Introduction
7

zFor models UPS602N2004N0B0 (6 kVA ) & UPS103N2004N0B0 (10 kVA )
1 2
www.deltapowersolutions.com
Delta UPS - Amplon Family
User Manual
The power behind competitiveness
N Series, Single Phase
6/ 10 kVA
ONOFF
SETUP
ON OFF
SETUP
3
456
7
8
9
10
11
x 2 x 4 x 3
x 2
x 6
No. Item Q’ty
1UPS 1 PC
2Parallel Cable 1 PC
3User Manual 1 PC
4CU Terminal_ Type A 2 PCS
5CU Terminal_ Type B 4 PCS
6CU Terminal_ Type C 3 PCS
7Battery Terminal Box 1 PC
8Battery Terminal Box Cover 1 PC
9Screw for Battery Terminal Box Cover 2 PCS
10
USB Cable 1 PC
11
Cable Tie 6 PCS

8
Amplon N Series

zFor models UPS602N2004N0BA (6 kVA ) & UPS103N2004N0BA (10 kVA )
1 2
www.deltapowersolutions.com
Delta UPS - Amplon Family
User Manual
The power behind competitiveness
N Series, Single Phase
6/ 10 kVA
ONOFF
SETUP
ON OFF
SETUP
3
456
7
8
9
10
11
x 2 x 4 x 3
x 2
x 6
No. Item Q’ty
1UPS 1 PC
2Parallel Cable 1 PC
3User Manual 1 PC
4CU Terminal_ Type A 2 PCS
5CU Terminal_ Type B 4 PCS
6CU Terminal_ Type C 3 PCS
7Battery Terminal Box 1 PC
8Battery Terminal Box Cover 1 PC
9Screw for Battery Terminal Box Cover 2 PCS
10
USB Cable 1 PC
11
Cable Tie 6 PCS
NOTE:
1. If there is any damage or anything missing, please immediately
contact the dealer from whom you purchased the unit.
2. If the UPS needs to be returned, carefully repack the UPS and all of
the accessories using the original packing material that came with the
unit.

9
Chapter 3 Operation Panel
Chapter 3:Operation Panel
)LJXUH2SHUDWLRQ3DQHO
ON OFF
SETUP
Hz
KW
KVA
AH
MIN
MIN ECO V
V%
IN
SET IN OUT BATT
RUN TIME
°C
LOAD TEST
3.1 LED Indicators
3.3 LCD Display (including
3.4 7-Segment Display &
3.5 16-Segment Display)
3.2 Multi-function Buttons
3.1 LED Indicators
No. LED Description
1Indicates the output status.
1. On (green): There is output.
2. Off: There is no output.
2Indicates the warning status.
1. On (red): The UPS is in failure mode.
2. Flash (red): The UPS’s working conditions are abnormal.

10
Amplon N Series
3.2 Multi-function Buttons
No. Multi- function
Button Description
1The button has two functions. Please refer to the following for
detailed information.
1. Buzzer On/ Off:
When the buzzer is on, press the button for 0.1 second to
turn off the buzzer. When the buzzer is off, press the button
for 0.1 second to turn on the buzzer.
&RQ¿UPDWLRQ
In setup mode, press the button for 0.1 second to enter into
WKHLWHPWKDW\RXZDQWWRVHWXSRUFRQ¿UP\RXUSDUDPHWHU
setup.
2ON The button has three functions. Please refer to the following for
detailed information.
1. Turn-on:

zIn bypass mode, press and hold the button for 3 seconds,
release it after you hear one beep and the UPS will run in
on-line mode.

zCold start: When there is no AC input, press and hold the
button for 3 seconds, release it after you hear one beep
and the UPS will start up in battery mode.
2. Battery Test:

zA battery test can only be executed in on-line mode.

zFor manual battery test, please press and hold the button
for 3 seconds, release it after you hear one beep, and the
UPS will transfer to run in battery mode and perform a
10-second battery test. If the test result is ok, the 7-seg-
ment display will show ‘PAS’ and the UPS will return to
on-line mode. If the test result is abnormal, the 7-segment
display will show ‘FAL’, the no-battery/ battery replace-
ment icon ( ) will illuminate and the UPS will return to
on-line mode. For 7-segment display information, please
refer to  6HJPHQW'LVSOD\.

11
Chapter 3 Operation Panel
No. Multi- function
Button Description
2ON NOTE:

zFor models UPS602N2004N035 (6 kVA ) &
UPS103N2004N035 (10 kVA ) &
UPS602N2004N0BA (6kVA) &
UPS103N2004N0BA (10kVA):
For automatic regular battery test, you must install the
UPSentry 2012 software (please download from http://
www.deltapowersolutions.com/en-in/mcis/software-
FHQWHUSKSRUFRQ¿JXUHWKH6103FDUGRSWLRQDORU
ModBus card (optional).

zFor models UPS602N2004N0B0 (6 kVA ) &
UPS103N2004N0B0 (10 kVA ):
For automatic regular battery test, you must install the
UPSentry 2012 software (please download from http://
www.deltapowersolutions.com/en-in/mcis/software-
FHQWHUSKSRUFRQ¿JXUHWKHPLQL6103FDUGRSWLRQDO
or mini ModBus card (optional).
3. Scrolling Up/ Increasing Number:

zPress the button for 0.1 second to go to the previous dis-
play or increase number.
3OFF The button has three functions. Please refer to the following for
detailed information.
1. Turn-off:

zIn on-line mode, press and hold the button for 3 seconds,
release it after you hear one beep and the inverter will be
off and the UPS will transfer to run in bypass mode.
The UPS will keep charging the batteries when the UPS
is in bypass mode. To fully turn off the UPS, please
completely disconnect the UPS from the input power.

zIn battery mode, press and hold the button for 3 seconds,
release it after you hear one beep and the UPS will turn
off its output.

12
Amplon N Series
No. Multi- function
Button Description
3OFF 2. Scrolling Down/ Decreasing Number:
Press the button for 0.1 second to go to the next display or
to decrease number.
3. Fault Clear:
When the UPS has a fault condition, press and hold the
button for 3 seconds, release it after you hear one beep and
the UPS will clear the fault condition and return to standby
mode.
NOTE:
When the UPS clears the fault condition, it doesn’t mean
that the fault has been automatically eliminated but
means that the buzzer has been turned off. For more
information, please refer to (UURU&RGH,QIRUPDWLRQ
and &KDSWHU7URXEOHVKRRWLQJ.
4ON
SETUP

zEntering into the Setup Mode
Simultaneously press the and ON these two buttons
for 3 seconds to enter into the setup mode.

zExiting from the Setup Mode
In setup mode, press these two buttons simultaneously for 3
seconds to exit from the setup mode.
NOTE:
For more information about the setup mode, please
refer to 6HWXS0RGH3OHDVHQRWHWKDWRQO\TXDOL¿HG
service personnel can perform setup action.
NOTE:
The backlight of the LCD automatically turns off after 3 minutes of inactivity.
You can press any button to wake up the display and enable each button
function. The duration of backlight (3 minutes) cannot be changed.

13
Chapter 3 Operation Panel
3.3 LCD Display
Hz
KW
KVA
AH
MIN
MIN ECO V
V%
IN
SET IN OUT BATT
RUN TIME
°C
LOAD TEST
No. Icon Naming Description
1AC
Icon Indicates the input source status.
1. ON: The AC input is within the acceptable
bypass range.
2. Flashing: The AC input is out of the accep-
table bypass range but is able to let the unit
operate in on-line mode.
3. OFF: The AC input is out of the acceptable
bypass range and is not able to let the unit
operate in on-line mode.
2Output
Icon Indicates the output status.
1. ON: There is output.
2. OFF: There is no output.
3Battery
Power
Icon
Indicates the battery power status.
1. ON: The UPS runs in battery mode or the
batteries are charging.
2. OFF: It is not the batteries to supply power to
the connected loads or the batteries are not
charging.
4PFC
Icon Indicates the PFC status.
1. ON: The PFC is running.
2. OFF: The PFC is not running.

14
Amplon N Series
No. Icon Naming Description
5Inverter
Icon Indicates the inverter status.
1. ON: The inverter is running.
2. OFF: The inverter is not running.
6Standby
Mode
Graph
Illuminates when the UPS is operating in stand-
by mode.
7Online
Mode
Graph
Illuminates when the UPS is operating in on-
line mode.
8Battery
Mode
Graph
Illuminates when the UPS is operating in bat-
tery mode.
9Bypass
Mode
Graph
Illuminates when the UPS is operating in by-
pass mode.
10 ECO
Mode
Graph
Illuminates when the UPS is operating in ECO
mode.
11 ECO ECO
Mode Illuminates when the UPS is operating in ECO mode. It is bypass to supply power to the con-
nected loads in ECO mode.
12 Buzzer
Off
Icon
Illuminates when the buzzer is disabled.
13 Parallel
Icon 1. ON: The UPS is in parallel mode.
2. OFF: The UPS is in single mode.
NOTE:
1. You can parallel at maximum four UPS
units. To enhance parallel reliability,
please adopt the Daisy Chain method
to execute parallel configuration.
Please note that parallel UPSs cannot
share common batteries.

15
Chapter 3 Operation Panel
No. Icon Naming Description
2. Only when the parallel icon illumi-
nates can you perform turn on proce-
dures for parallel units.
14 Load
Level
Bar
Graph
1. ON:7RWDOFDSDFLW\RIWKHFRQQHFWHG
loads*1.
2. Flashing: Overload.
15 Battery
Level
Bar
Graph
1. ON:7KHUHPDLQLQJEDWWHU\FDSDFLW\*1.
2. Flashing: Low battery.
NOTE:
*1means that:
WKHst segment will illuminate.
WKH¿UVWWZRVHJPHQWVZLOOLOOXPLQDWH
WKH¿UVWWKUHHVHJPHQWVZLOOLOOXPLQDWH
DOOVHJPHQWVZLOOLOOXPLQDWH
3.4 7-Segment Display
Hz
KW
KVA
AH
MIN
MIN ECO V
V%
IN
SET IN OUT BATT
RUN TIME
°C
LOAD TEST

16
Amplon N Series
No. Display Meaning Category
17-segment
display Number
The combination of the three
categories (left-hand side)
presents relevant information
such as input voltage, output
voltage, output frequency,
load capacity etc.
2 SET Setup mode. Please refer to
6HWXS0RGH
Status
3INInput
4OUTOutput
5BATTBattery status
6 LOAD Load status
7 TEST Test
8AHAmpere hour
Unit
9ACurrent
10 V Voltage
11 % Percentage
12 Hz Frequency
13 KVA kVA
14 KW kW
15 MIN Minute
16 °C The UPS’s inter-
nal temperature.