Dentsply Sirona MIDWEST AUTOMATE User manual

MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
www.dentsplysirona.com
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
87478-0220
Instructions for Use
EN

Table of Contents EN
2
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
1Important Information........................................................3
System contents ..................................................................3
General................................................................................3
Contraindications.................................................................3
Intended use........................................................................3
Qualification of the user.......................................................3
Disposal of consumables.....................................................3
Safety information for Midwest®Plus Automate Spray ........4
Applied symbols...................................................................4
Exclusion of liability..............................................................4
2Product Overview..............................................................5
Overview of the unit.............................................................5
Back panel...........................................................................5
Operating keypad.................................................................6
3Installation.........................................................................7
Location ...............................................................................7
Electrical requirements ........................................................7
Power and air connections...................................................7
Installing spray can ..............................................................7
Attaching maintenance adaptors to handpiece cleaning
ports.....................................................................................7
4Operation ..........................................................................8
Handpiece maintenance ......................................................8
Handpiece chuck maintenance............................................8
5Maintenance .....................................................................9
Using Midwest®Plus Automate Spray Can..........................9
To change automate absorption pad and particulate filter...9
To change automate particulate filter...................................9
To change the maintenance expel time.............................10
Disposal.............................................................................10
Cleaning and disinfecting...................................................10
Replacing fuses.................................................................10
Replacing front door seal...................................................10
Replacing rubber foot ........................................................10
Replacing air tube..............................................................10
6Troubleshooting..............................................................11
7Information On Electromagnetic Compatibility................12
8Accessories.....................................................................14
9Replacement Parts .........................................................15
10 Specifications..................................................................16
Type labels ........................................................................16
11 Warranty .........................................................................17
All trademarks referred to are the property of their respective owners.
Manufactured for:
Sirona Dental Systems GmbH
Fabrikstrasse 31
D-64625 Bensheim
Germany
www.dentsplysirona.com

1 Important Information EN
3
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
1 Important Information
Congratulations on selecting the Midwest®Automate®, an Automated Handpiece Maintenance System. We are confident
you have purchased the finest equipment of its type. It is a compact, counter-top unit that features a number of
maintenance cycles designed to meet your handpiece maintenance needs.
Details of installing, operating and servicing this unit are contained in these Instructions for Use. To ensure years of safe,
trouble-free service read the instructions before operating this unit and keep them for future reference. Operational,
maintenance and replacement instructions must be followed to perform as designed. Contents of this manual are subject
to change without notice to reflect changes and improvements to the product.
System contents
•Midwest®Automate®maintenance system
•Power Cord
•Air-Connection hose with wall connector
•Absorbent Pads
•Instructions for Use
General
The unit has been developed and manufactured according to the latest quality and safety standards. However,
some precautions should be taken for installation and operation.
•When leaving the system unattended for an extended period (e.g. vacations), it must be disconnected from the power
supply.
•The unit contains a spray can and must be protected from heating up over 122°F (50°C).
•Modifications by third parties will result in voiding the warranty and cancellation of the electrical certification of this
product.
•Use only recommended original parts, as they are qualified in extensive tests for safety, function and suitability. Use of
other products or components shall void the warranty.
•Observe all warning information on the unit and the Instructions for Use.
•The unit must be supplied with the voltage indicated in the Instructions for Use and on the unit.
•Users must not attempt to service the unit exceeding those points described in the Instructions for Use.
•Never remove the cover of the unit and never insert objects through the holes or openings on the case. Non-
compliance may cause damage to the unit and/or may endanger the user.
Following maintenance in the unit, handpieces must be further treated (sterilized) according to local guidelines and
manufacturer recommendations.
Contraindications
Do not use on this system:
- 710078 Prophy Right Angle Sheath
- 720446 Triple-Seal Prophy Contra Angle Head
- 720445 Triple-Seal Prophy Right Angle Head
Do not sterilize maintenance adaptors.
Do not use maintenance adaptors on dental delivery systems.
Intended use
The Midwest®Automate®System is intended for cleaning, service and maintenance of tool holders, angle pieces and
turbines used in dentistry. For further information about the suitability of instruments to service, refer to manufacturer
instructions.
Qualification of the user
The unit may only be used by trained personnel who may include dentists and their assistants.
The unit may only be used for applications defined in “Intended Use”.
The unit must be operated in well ventilated areas to avoid possible explosive conditions.
Disposal of consumables
Waste incurred must be recycled or disposed of in a manner harmless to human beings and the environment per
relevant regulations.

1 Important Information EN
4
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
Safety information for Midwest®Plus Automate Spray
(Refer to full safety data sheet for complete information)
Adverse reactions
If you experience breathing difficulty, supply fresh air and seek immediate medical attention.
The product generally does not irritate skin, but if irritation occurs seek medical attention.
If eye contact occurs, rinse opened eye for several minutes under running water. If problems persist, seek medical
attention.
If swallowing occurs, seek immediate medical attention.
Before first use
Store this unit 24 hours at room temperature before first use!
Firefighting measures
•Suitable extinguishing agents: CO2, extinguishing powder or water spray
•For safety reasons unsuitable extinguishing agents: Water with full jet
•Special hazards arising from the substance or mixture: No further relevant information available
•Protective equipment: No special measures required
Applied symbols
Appearing in the manual:
Appearing on the unit:
Indicates a hazardous
situation that can lead to
serious injury or death
LED "Ready to operate"
Disposal information see
"Important Information" -
"Disposal"
Indicates a hazardous
situation that can lead to
property damage or minor to
moderate injury
LED “Spray can empty"
Consult "Instructions for
Use"
Important information
Start button for "Chuck
Maintenance"
MET test mark
Start button for "Maintenance
Cycle"
Manufacturing date
Fuse
Appearing on the packaging:
Fragile, handle with care
Stacking limitation
Humidity limitation
Keep dry
Temperature limitation
Package unit
Transport upright
Atmospheric pressure limitation
Exclusion of liability
Supply of spare parts, service and maintenance may only be carried out by authorized personnel. Dentsply Sirona shall
assume no liability for accidental, special or consequential damage caused by maintenance or service of the Midwest®
Automate®unit by third parties, or for use of equipment or parts manufactured by third parties, including loss of profit,
any commercial loss, economic loss or loss incurred by personal injury.

2 Product Overview EN
5
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
2 Product Overview
Overview of the unit
Operating keypad
Handpiece port orientation guides
Handpiece maintenance ports
Chuck maintenance port
Absorption pad
Front door
Receptacle for Midwest®Plus
Automate Spray Can
Spray can chamber door
Midwest®Plus Automate Spray Can
Particulate filter (yellow)
Back panel
Type label
Power switch
Fuse drawer
Power supply input
Compressed air coupling
Compressed air regulator
Inlet air pressure display

2 Product Overview EN
6
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
Operating keypad
LED "Ready to operate"
LED "Spray can empty"
START button for “Maintenance Cycle"
LED "Handpiece Maintenance Port 1"
LED "Handpiece Maintenance Port 2"
LED "Handpiece Maintenance Port 3"
START button for "Chuck Maintenance"
LED "Chuck Maintenance Port"

3 Installation EN
7
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
3 Installation
Location
The Midwest®Automate®System may only be used in dental offices, dental hospitals and dental universities in the
ambient conditions given in the technical data chapter 10 "Specifications".
•Not in intensive care units
•The recommended operating temperatures are 41–104°F (5–40°C) with humidity of 25–85%
•Avoid installing the unit in direct sunlight or close to a heat source (e.g. vents or radiators)
•Frequency of use: up to several times a day
•Length of use: from one minute to several hours a day
•May be used with other units (sterilization unit, washer, etc.)
•To be operated in ambient light between 100 Lux and 1,500 Lux
•Ambient temperature in immediate proximity of the unit during operation: max. 35°C (95°F)
•Unit should be placed on the soiled side of the sterilization area.
•The unit should be operated in a clean area
•The unit must be operated in well ventilated areas to avoid possible explosive conditions
•The unit should be placed on a flat, level, water-resistant surface
•Never install and operate the unit on a sloped surface. Surface must be adequate to accommodate the front door when
it is fully open.
Electromagnetic environment
The unit has been tested and meets applicable standards for electromagnetic emissions. While the unit does not emit
any radiation, it may itself be affected by other equipment which does. We recommend that the unit be kept away from
potential sources of interference.
Electrical requirements
Use properly grounded and fused power sources with the same voltage rating as indicated on the label at the
back of the unit. Avoid multiple outlet receptacles. If using a surge suppressor power bar, plug in one unit only.
The power input plug on the back of the unit is to be used as a separating device to the power supply network.
Power and air connections
Insert power plug into socket.
Fasten and secure compressed air hose onto coupling.
Ensure compressed air regulator indicates 4 bar (58 psi).
To adjust inlet air pressure, pull out handle on the compressed air regulator and turn clockwise (increase) or counter-
clockwise (decrease) until 4 bar (58 psi) is displayed.
Push handle on the compressed air regulator back in and lock it.
Use compressed air according to the information contained in the chapter 10 "Specifications", to ensure proper function.
Installing spray can
(see chapter 5 "Maintenance")
Attaching maintenance adaptors to handpiece cleaning ports
(see chapter 4 "Operation")

4 Operation EN
8
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
4 Operation
Handpiece maintenance
Do not use on this system:
- 710078: Prophy Right Angle Sheath
- 720446: Triple-Seal Prophy Contra Angle Head
- 720445: Triple-Seal Prophy Right Angle Head
Insert Midwest®Plus Automate Spray Can.
(see chapter 5 "Maintenance" “Insert spray can”)
Turn on power
LED (ready to operate) light turns green.
Open front door.
Attach applicable maintenance adaptors to handpiece maintenance
ports.
Prior to installing a handpiece to the maintenance system, scrub
and clean the handpiece under running water (head pointing up)
using a soft sponge to remove external debris.
Install handpiece to appropriate adaptor, ensuring Handpiece Chuck
opening (Bur tube) is facing front, back or down.
NOTE:
If your fixed back end handpiece faces left or right, utilize "380422 –
Midwest®90° Maintenance Adaptor" to correct the positioning.
Close front door.
Press (Start Button) on operating keypad.
The cycle will run automatically. Blinking of LEDs 1, 2 or 3 indicate
port is in use. Each handpiece port is lubricated in succession.
Upon completion of each maintenance cycle LEDs of each loaded
port will be illuminated.
Open front door.
Remove handpiece(s).
LEDs will turn off on removal of handpieces.
Check handpiece chuck for visual presence of oil.
If no oil is visible on chuck, see "Troubleshooting" chapter 6.
Once a week: Ensure maintenance adaptors are securely
attached to handpiece maintenance ports.
Tighten coupling nut as needed.
Handpiece chuck maintenance
Wear safety glasses.
Turn on power.
LED (ready to operate) lights green.
Open front door.
Hold handpiece Bur Tube to chuck maintenance port.
Press (Start Button) on operating keypad.
Program runs automatically.
LED next to illuminates during process.
Remove handpiece when cycle is complete and LED is off.

5 Maintenance EN
9
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
5 Maintenance
Using Midwest®Plus Automate Spray Can
Insert Spray Can
Open side door.
Lift lever and hold.
Fully seat spray can in holder.
Release lever.
Close side door.
NOTE:
Use only original Midwest®Plus Automate Spray Cans.
Remove spray can
Open side door.
Lift lever and hold.
Tilt bottom of can outwards.
Pull can out.
Release lever.
Close side door.
Disposing empty spray cans
Follow local regulations for disposal.
Safety information
Check for any leaks every time a new bottle is installed!
Replace faulty or leaky spray cans immediately!
Protect the spray can from direct sunlight!
To change automate absorption pad and particulate filter
Open the front door.
Pull out and remove saturated absorption pad from the two holding brackets.
Hang new absorption pad on to the two holding brackets.
Close the front door.
NOTE:
Use only original Midwest®Absorption Pads and Particulate Filters
It is recommended to replace the absorption pad each time a new Midwest®Plus Automate Spray Can is used, or more
frequently as needed.
To change automate particulate filter
NOTE:
It is recommended to replace the particulate filter at every third time a new absorption pad is replaced or as necessary.
Open the front door.
Pull out and remove yellow particulate filter at the bottom of the unit behind the absorption pad.
Place a new particulate filter with the yellow side faced down.
Ensure absorption pad is positioned back in place.
Close the front door.
NOTE:
Use only original Midwest®Particulate Filters (included in the Midwest® Automate®Absorption Pad Kit).
Insert Spray Can
Remove Spray Can

5 Maintenance EN
10
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
To change the maintenance expel time
Turn power off.
Press and hold .
Turn power on.
The LED (ready to operate) flashes.
Use to change settings.
Maintenance time is set as follows:
15 sec
LED 1 illuminates
30 sec
LED 2 illuminates
45 sec
LED 3 illuminates
60 sec
LED’s 1, 2 and 3 illuminates together
When time setting is chosen, wait 5 seconds for change to take effect.
After which the unit assumes normal operation (LED illuminates).
NOTE:
Factory default setting is 60 seconds.
Disposal
See "Disposal of Consumables" (page 3).
Cleaning and disinfecting
Clean and disinfect powder coated paint surfaces with common disinfectants (Dentsply Sirona Volowipes, SciCan
OPTIM wipes, Metrex CaviWipes).
Clean operating keypad with soft cloth dampened with water.
Replacing fuses
Disconnect power.
Pull out fuse drawer.
(Push both flaps of the fuse drawer inward.)
Replace fuses.
Insert fuse drawer.
Use only Midwest®supplied fuses.
Replacing front door seal
Remove damaged door seal (at least one complete side).
Clean the bonding surface with rubbing alcohol.
Cut door seal to length.
Place new adhesive door seal flush with the inner edge of door.
Replacing rubber foot
Remove rubber foot.
Using the same screw and washer attach new rubber foot.
Replacing air tube
Remove tube from wall air supply.
Press and hold release ring on top of the compressed air coupling (page 5) and pull air tube out.
Slide a new tube on to the compressed air coupling.
Attach opposite end of tube to wall air supply.

6 Troubleshooting EN
11
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
6 Troubleshooting
Fault
Possible cause
Remedy
LED flashing
Spray can failure
Re-insert or replace spray can
Compressed air not connected
or not on/flowing
Turn on / connect compressed air
Door cannot be closed properly
Handpieces placed incorrectly
Handpiece chucks must be directed towards
the front or back
LED is off
No power supply
Plug in power cord
Turn unit on
Handpiece maintenance cycle
does not start
Front door not closed
Close front door
Top of oil can is more than half
filled with oil
O-Ring worn or damaged
Contact service (chapter 11)
No oil at handpiece chuck after
maintenance cycle
Clogged handpiece
Consult handpiece instructions
Oil system malfunction
Contact service (chapter 11)

7 Information on Electromagnetic Compatibility EN
12
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
7 Information On Electromagnetic Compatibility
Information on electromagnetic compatibility
The unit is suitable for use in the specified electromagnetic environment. The purchaser or user of the unit should assure that it is used in an
electromagnetic environment as described below:
Emission Test
Compliance
Electromagnetic Environment
Radio-Frequency Emissions CISPR 11
Group 1
The unit uses RF energy only for its internal function. Therefore, the RF
emission is very low and not likely to cause any interference in nearby
electronic equipment.
Radio-Frequency Emissions CISPR 11
Class B
The unit is for use in all facilities including residential facilities and
facilities that are directly connected to a public power supply that also
supplies residential buildings.
Harmonic emissions IEC 61000-3-2
Class A
Voltage fluctuations / flicker emissions IEC
61000-3-3
Complies
Immunity tests
IEC 60601-test level
Conformance level
Electromagnetic environment - guidelines
Electrostatic discharge
(ESD)
IEC 61000-4-2
± 6 kV contact discharge
± 8 kV atmospheric
discharge
± 6 kV contact discharge
± 8 kV atmospheric
discharge
Floors should be made of wood or concrete or
have ceramic tiles. When the floor is covered
with synthetic material, the relative humidity
must be at least 30%.
Fast transient electrical
disturbances/ Bursts
IEC 61000-4-4
± 2 kV for power lines
± 2 kV for in-put and out-
put lines
± 2 kV, for power lines not
applicable
The quality of the supply voltage should
correspond to that of a typical business or
hospital environment.
Surges
IEC 61000-4-5
± 1 kV push-pull voltage
± 2 kV common mode
voltage
± 1 kV push-pull voltage
± 2 kV common mode
voltage
The quality of the supply voltage should
correspond to that of a typical business or
hospital environment.
Voltage interruptions,
short-term interruptions
and fluctuations of the
supply voltage
IEC 61000-4-11
0 % UT for 0,5 periods
40 % UT for 5 periods
70 % UT for 25 periods
0 % UT for 250 periods
0 % UT for 0,5 periods
40 % UT for 5 periods
70 % UT for 25 periods
0 % UT for 250 periods
The quality of the supply voltage should
correspond to that of a typical business or
hospital environment. When the user of the unit
needs continued operation even when the
power supply is interrupted, it is recommended
to supply the unit from an uninterrupted power
supply or a battery.
Magnetic field with a supply
frequency (50/60 Hz)
IEC 61000-4-8
3 A/m
not applicable
not applicable
Conducted HF disturbances
IEC 61000-4-6
3 V eff
150 kHz to 80 MHz
outside of the ISM bandsa
10 V eff
Portable and mobile radio devices should not be used closer
to the unit (including the electrical lines) than the
recommenced safe distance calculated using the equation
for the transmission frequency. Recommended safe
distance:
d = 1.17 P
d = 0.35 P for 80 MHz to 800 MHz
d = 0.70 P for 800 MHz to 2.5 GHz
with P as the maximum rated power of the transmitter in
Watts (W) according to the transmitter manufacturer, and d
as the recommended safe distance in meters (m). b The field
strength of stationary radio transmitters should be less than
the conformance level at all frequencies in an on-site checkc.
d Disturbances are possible close to devices that have the
following symbol.
Radiated HF disturbances
IEC 61000-4-3
10 V/m
80 MHz to 2.5 GHz
10 V/m

7 Information on Electromagnetic Compatibility EN
13
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
NOTE: UT is the alternating mains voltage before the test level is used.
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not be applicable in every case. The spread of electromagnetic waves is absorbed and reflected by buildings,
objects and people.
aThe ISM frequency bands (for industrial, scientific and medical applications) between 150 kHz and 80 MHz are 6.765 MHz to 6.795 MHz;
13.553 MHz to 13.567 MHz; 26.957 MHz to 27.283 MHz and 40.66 MHz to 40.70 MHz
bThe conformance levels in the ISM frequency bands between 150 kHz and 80 MHz and the frequency range of 80 MHz and 2.5 GHz are
intended to reduce the probability that mobile and portable communications equipment will produce disturbances when they are unintentionally
brought near the patient. For this reason, the additional factor of 10/3 is used when calculating the recommended safe distances within these
frequency ranges.
cThe field strength of stationary transmitters such as base stations of mobile telephones and land mobile radio devices, amateur radio stations,
AM and FM, radio and television broadcasters cannot be theoretically predetermined. To determine the electromagnetic environment of stationary
transmitters, a study of the location should be considered. When the measured field strength at the site where the unit is used exceeds the above
conformance level, the unit should be monitored to demonstrate proper function. When unusual performance features are observed, additional
measures may be necessary such as realigning or moving the unit.
dWithin the frequency range of 150 kHz to 80 MHz, the field strength should be less than 3V eff V/m
Recommended safe distance between portable and mobile HF telecommunications equipment and the unit.
The unit is intended for use in an electromagnetic environment in which HF disturbances are controlled. The customer or the user of the unit can
help prevent electromagnetic disturbances by maintaining the minimum distance between portable and mobile HF telecommunications devices
(transmitters) and the unit depending on the output of the communication device as indicated below.
Rated power of the
transmitter / W
Safe distance depending on the transmission frequency / m
150 kHz to 80 MHz d=0.35 P
80 MHz to 800 MHz d=0.35 P
800 MHz to 2.5 GHz d=0.70 P
0.01
0.04
0.04
0.07
0.1
0.11
0.11
0.22
1
0.35
0.35
0.70
10
1.11
1.11
2.21
100
3.50
3.50
7.00
For transmitters whose maximum rated power is not in the above table, the recommended safe distance d in meters (m) can be calculated using
the equation for the respective gap, where P is the maximum rated power of the transmitter in Watts (W) according to the manufacturer's
information.
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not be applicable in every case. The spread of electromagnetic waves is absorbed and reflected by buildings,
objects and people.

8 Accessories EN
14
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
8 Accessories
Order from your Dentsply Sirona authorized dealer.
Image
SKU #
Description
380200
Midwest®Automate®Package
Includes:
Maintenance System, Absorbent pads, IFU, Air tube with wall connector,
Power connection
Midwest®Plus Automate Spray Can
Midwest Maintenance Adaptor Order Form
880090
Midwest®Stylus™ ATC / Phoenix Pro Maintenance Adaptor
380090
Midwest®Style Maintenance Adaptor
380410
Midwest®Quick Connect Maintenance Adaptor
380420
Midwest®Low Speed Attachment Adaptor
380421
Low Speed Motor Adaptor
380422
Midwest®90° Maintenance Adaptor
380430
E-Type Maintenance Adaptor
380440
KaVo®INTRA Head Maintenance Adaptor
380450
K Style Maintenance Adaptor
380460
W&H®Highspeed Maintenance Adaptor
380470
Star®Highspeed Maintenance Adaptor
380480
NSK®Highspeed Maintenance Adaptor
380490
Bien-Air®Highspeed Maintenance Adaptor
380500
Sirona®T1 E-style Low Speed Attachment Maintenance Adaptor
380510
Sirona®Style Highspeed Maintenance Adaptor
Do not sterilize maintenance adaptors.
Do not use maintenance adaptors on dental delivery systems.

9 Replacement Parts EN
15
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
9 Replacement Parts
Order from your Dentsply Sirona authorized dealer.
Image
SKU #
Description
380520
Midwest®Automate®Absorption Pad (6 Pack)
380180
Midwest®Plus Automate Spray Can
380260R
Midwest®Stylus™ ATC / Phoenix Pro Maintenance Adaptor
Replacement O-Ring Set
790259R
Midwest®Style Maintenance Adaptor
Replacement O-Ring Set
380265R
Midwest®Style Maintenance Adaptor
Replacement Spring
380280R
Midwest®Low Speed Attachment Adaptor
Replacement O-Ring Set
380285R
Star®Highspeed Maintenance Adaptor
Replacement O-Ring Set
773002R
Midwest®4-Tube Hose Connector Blue Gasket
380405R
K Style Maintenance Adaptor
Replacement O-Ring Set
380425R
E-Type Maintenance Adaptor
Replacement O-Ring Set
380650R
W&H®Highspeed Maintenance Adaptor
Replacement O-Ring Set
380655R
Bien-Air®Highspeed Maintenance Adaptor
Replacement O-Ring Set
380660R
Sirona®Style Highspeed Maintenance Adaptor
Replacement O-Ring Set
380360R
Midwest®Automate®Rubber Foot
380390R
Midwest®Automate®Tubing - Air Compressor (blue external)
380415R
Midwest®Automate®Fuse T2
380445R
Midwest®Automate®Front Door Seal Set

10 Specifications EN
16
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
10 Specifications
Dimensions:
Length:
11.4 inches (289 mm)
Width:
9.1 inches (232 mm)
Height:
16.3 inches (414 mm)
Weight:
9.6 kg (23.7 lbs)
Electrical rating:
Rated voltage:
100 –230 V 10%
Rated frequency:
50 / 60 Hz
Rated power:
max. 30 VA
Protection Class:
I
Protection:
covered
Installation category:
Cat. II
Pollution degree:
P 2
Ambient operating temperature:
5 –40°C (41 –104°F)
Noise levels:
60 (65) dB(A)
Humidity:
max. 85%
Max. Altitude:
2,000 m
Operating location:
Indoor only
Onsite pressure:
4 –7 bar (58 –100 psi)
Recommended operating pressure:
4 –4.5 bar (58 –65 psi)
Air consumption during operation:
40 Nl/min
Compressed air quality:
Residual oil content:
max. 0.1 mg/m³
Residual dust:
max. 1 µm; max. 1 mg/m³
Residual water:
max. 0.1 g/m³ at -40°C (-40°F)
Power fuses:
Rated current:
2 A
Rated voltage:
250 V
Tripping characteristic:
Large (T)
Interrupting rating:
H
Storage and transport conditions
Ambient temperature:
Transport:
-30 –70°C (-22 –158°F)
Storage:
0 –40°C (32 –104° F)
Relative humidity:
5 –95%
Atmospheric pressure:
700 –1,060 hPa
Type labels
The explanations of the symbols are described in chapter 1 "Important Information".

11 Warranty EN
17
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System
11 Warranty
The Midwest®Automate®Handpiece Maintenance Unit is guaranteed to be free of defects in material and
workmanship for a period of 36 months from date of purchase –provided the maintenance unit has been operated
and maintained as prescribed in these Instructions for Use, at the discretion of Dentsply Sirona, and has not been
subject to apparent misuse, abuse or accident.
All questionable, defective or loose parts must be returned with proof of purchase, transportation prepaid.
Not following the provided instructions for installation, operation and maintenance will void the warranty.
There are no warranties, express or implied, which extend beyond the description of the face hereof. Dentsply Sirona
neither assumes, nor authorizes any person to assume for it, any other liability in connection with the sale or use of
its products.
Damages are limited strictly to repair or replacement of parts.
Dentsply Sirona expressly disclaims liability for incidental and consequential damages resulting from the use of the
products.
Claims covered by this warranty will be honored when presented through your Dentsply Sirona professional distributor
within 30 days from discovery of defect within the applicable warranty period.
This warranty excludes consumables, such as cleaner spray, absorbent pads, gaskets, rubber parts, seals and
O-rings etc.
MAINTENANCE & REPAIR –within USA
Dentsply Sirona US Repair Center
Midwest®Air Repair
500 W College Avenue
York, PA 17401
800-800-7202
www.midwestairrepair.com
Call or go online to schedule your pick-up.
MAINTENANCE & REPAIR –within Canada
Contact your dealer of choice to arrange maintenance & repair.

EN
MIDWEST®AUTOMATE®
Automated Handpiece Maintenance System

MIDWEST®AUTOMATE®
Système d'entretien automatisé de pièces à main
www.dentsplysirona.com
MIDWEST®AUTOMATE®
Système d'entretien automatisé de pièces à main
87478-0220
Mode d’emploi
FR

Table des matières FR
20
MIDWEST®AUTOMATE®
Système d'entretien automatisé de pièces à main
1Informations importantes.................................................21
Contenu du système..........................................................21
Généralités.........................................................................21
Contre-indications..............................................................21
Utilisation prévue ...............................................................21
Qualification de l'utilisateur ................................................21
Élimination des consommables..........................................21
Consignes de sécurité pour l'aérosol Midwest®Plus
Automate Spray.................................................................22
Symboles utilisés...............................................................22
Exclusion de responsabilité................................................22
2Vue d'ensemble de l'appareil ..........................................23
Vue d'ensemble de l'appareil.............................................23
Panneau arrière.................................................................23
Pavé de commande...........................................................24
3Installation.......................................................................25
Emplacement.....................................................................25
Alimentation électrique.......................................................25
Raccords d'alimentation et d'air.........................................25
Installation du contenant aérosol .......................................25
Fixation des adaptateurs d'entretien aux ports de nettoyage
de pièces à main................................................................25
4Utilisation.........................................................................26
Entretien de pièces à main ................................................26
Entretien du mandrin de la pièce à main ...........................26
5Entretien..........................................................................27
Utilisation du contenant aérosol Midwest®Plus Automate
Spray .................................................................................27
Changement du tampon absorbant ...................................27
Changement du filtre à particules Automate......................27
Réglage du temps d'entretien............................................28
Élimination.........................................................................28
Nettoyage et désinfection ..................................................28
Remplacement des fusibles...............................................28
Remplacement de l'adhésif d'étanchéité de la porte avant 28
Remplacement d'un pied de caoutchouc...........................28
Remplacement du tube d'air..............................................28
6Dépannage .....................................................................29
7Informations sur la compatibilité électromagnétique.......30
8Accessories.....................................................................32
9Pièces de rechange........................................................33
10 Caractéristiques..............................................................34
Plaque signalétique ...........................................................34
11 Garantie..........................................................................35
Toutes les marques commerciales mentionnées appartiennent à leurs propriétaires respectifs.
Fabriqué pour :
Sirona Dental Systems GmbH
Fabrikstrasse 31
D-64625 Bensheim
Allemagne
www.dentsplysirona.com