Desa TC106A User manual

VARIABLE 40-80,000 BTU/HR
75-200,000 BTU/HR
PROPANE CONSTRUCTION CONVECTION HEATER
OWNER’S MANUAL
IMPORTANT: Read and understand this manual before
assembling, starting or servicing heater. Improper use
of heater can cause serious injury. Keep this manual for
future reference.
GENERAL HAZARD WARNING:
Failure to comply with the precautions and instructions
provided with this heater, can result in death, serious
bodily injury and property loss or damage from hazards
of re, explosion, burn, asphyxiation, carbon monoxide
poisoning and/or electrical shock.
Only persons who can understand and follow the instruc-
tions should use or service this heater.
If you need assistance or heater information such as an in-
structions manual, labels, etc. contact the manufacturer.
Save this manual for future reference.
For more information, visit www.desatech.com
200 000
BTU/HR
TABLE OF CONTENTS
Safety .................................................................. 2
Unpacking............................................................ 3
Product Identication........................................... 3
Ventilation............................................................ 3
Theory of Operation............................................. 3
Propane Supply................................................... 4
Installation ........................................................... 4
Operation............................................................. 5
Storage................................................................ 7
Maintenance........................................................ 7
Troubleshooting................................................... 8
Specications ...................................................... 9
Replacement Parts.............................................. 9
Technical Services............................................... 9
Accessories ......................................................... 9
Parts .................................................................. 10
Warranty ............................................................ 14

www.desatech.com 121512-01C2
SAFETY
Propane Gas: Propane gas is odorless. An
odor-making agent is added to propane gas.
The odor helps you detect a propane gas
leak. However, the odor added to propane
gas may fade. Propane gas may be present
even though no odor exists.
Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this heater.
1. Install and use heater with care. Follow all
local ordinances and codes. In the absence
of local ordinances and codes, refer to
the Standard for Storage and Handling of
Liqueed Petroleum Gas, ANSI/NFPA 58
Natural Gas Installation Code, CAN/CGA
B149.2. This instructs on the safe storage
and handling of propane gases.
2. State of Massachusetts: The installation
must be made by a licensed plumber or
gas tter in the Commonwealth of Mas-
sachusetts.
3. Use only propane gas set up for vapor
withdrawal.
4. Provide adequate ventilation. Before us-
ing heater, provide at least a 2.5 square
foot (0.232 m2) (80,000 Btu/Hr heaters) or
6.0 square foot (0.557 m2) (200,000 Btu/
Hr heaters) opening of fresh, outside air.
5. For indoor use only. Do not use heater
outdoors.
6. Keep heater away from strong drafts,
wind, water spray, rain or dripping water.
7. Do not use heater in occupied dwellings
or in living or sleeping quarters.
8. Do not use heater in a basement or below
ground level. Propane gas is heavier than
air. If a leak occurs, propane gas may sink
to the lowest possible level.
9. Keep appliance area clear and free from
combustible materials, gasoline, paint
thinner and other ammable vapors and
liquids. Dust is combust ble. Do not use
heater in areas with high dust content.
10. Minimum heater clearances from combus-
tibles: 80,000 Btu/Hr heaters
Sides: 3 feet (91 cm); Top: 6 feet (1.83 m)
100-200,000 Btu/Hr heaters
Sides: 3 feet (91 cm); Top: 7 feet (2.1 m)
11. Keep heater at least six feet (1.83 m) from
propane tank(s).
12. Keep propane tank(s) below 100° F
(37.8° C).
WARNING: This product
contains and/or generates
chemicals known to the State
of California to cause cancer or
birth defects or other reproduc-
tive harm.
WARNING: Fire, burn inhala-
tion and explosion hazard. Keep
solidcombustibles,suchasbuild-
ingmaterials,paperorcardboard,
a safe distance away from the
heater as recommended by the
instructions.Neveruse theheater
inspaceswhichdoormaycontain
volatile or airborne combustibles
orproducts suchasgasoline, sol-
vents,paintthinner,dustparticles
or unknown chemicals.
WARNING: Not for home or
recreational vehicle use.
The heater is designed for use as a con-
struction heater in accordance with ANSI
Z83.7•CGA 2.14. Other standards govern
the use of fuel gases and heating products
for specic uses. Your local authority can
advise you about these. The primary purpose
of construction heaters is to provide tempo-
rary heating of buildings under construction,
alteration or repair. Properly used, the heater
provides safe economical heating. Products
of combustion are vented into the area being
heated.
We cannot foresee every use which may be
made of our heaters. CHECK WITH YOUR
LOCAL FIRE SAFETY AUTHORITY IF YOU
HAVE QUESTIONS ABOUT HEATER USE.
Carbon Monoxide Poisoning: Some people
are more affected by carbon monoxide than
others. Early signs of carbon monoxide poi-
soning resemble the u, with headaches, diz-
ziness and/or nausea. If you have these signs,
the heater may not be working properly. Get
fresh air at once! Check for proper ventilation
and have heater serviced.

www.desatech.com
121512-01C 3
200,000
BTU/HR
SAFETY
Continued
Outer
Shell
Ignitor
Button
Ball Valve
Control Knob
Button
Figure 1 - 200,000 Btu Model Shown
13. Use only the hose and factory preset
regulator provided with the heater.
14. Check heater for damage before each
use. Do not use a damaged heater.
15. Check hose before each use of heater.
If highly worn or cut, replace with hose
specied by manufacturer before using
heater.
16. Do not alter heater. Keep heater in its
original state.
17. Do not use heater if altered.
18. Locate heater on stable and level surface
if heater is hot or operating.
19. Not intended for use on nished oors.
This includes, but is not limited to carpet,
rugs, vinyl, treated and synthetic wood
ooring.
20. Never block air inlet (bottom of shell) or
air outlet (around top of shell) of heater.
21. Do not leave heater unattended.
22. Keep children and animals away from
heater.
23. Always run heater with control knob at LO,
MED or HI settings. Never set control knob
between OFF, LO, MED or HI settings.
24. Never move, handle or service a hot
or operating heater. Severe burns may
result. You must wait 15 minutes after
turning heater off.
25. To prevent injury, wear gloves when han-
dling heater.
26. Never attach duct work to heater.
27. Turn off propane supply to heater when
not in use.
28. Use only original replacement parts. This
heater must use design-specic parts.
Do not substitute or use generic parts.
Improper replacement parts could cause
serious or fatal injuries.
UNPACKING
1. Remove all packing items applied to
heater for shipment. Keep plastic cover
caps (attached to inlet connector and
hose/regulator assembly) for storage.
2. Remove all items from carton.
3. Check heater for any shipping damage.
If heater is damaged call DESA Heating,
LLC at 1-866-672-6040 for replacement
parts before returning to dealer.
PRODUCT
IDENTIFICATION
VENTILATION
WARNING: Provide at least
a 2.5 square foot (0.23 m2)
(80,000 Btu/Hr) or 6 square
foot (0.557 m2) (200,000 Btu/Hr)
opening of fresh, outside air
while running heater. If proper
fresh, outside air ventilation is
not provided, carbon monoxide
poisoning can occur. Provide
proper fresh, outside air ventila-
tion before running heater.
THEORY OF OPERATION
The Fuel System: The hose/regulator as-
sembly attaches to the propane gas supply.
This provides fuel to the heater.
The Ignition System: The piezo ignitor lights
the pilot.
The Automatic Control System: This system
causes the heater to shut down if the ame
goes out.
Valve
Inlet
Safety Pilot Valve

www.desatech.com 121512-01C4
200 000
BTU/HR
Figure 2 - Lifting Outer Shell
(200,000 Btu/Hr Model Shown)
1 Screw
per Clip
Outer
Shell
Clip in Slot
of Lower
Shell
PROPANE SUPPLY
You must provide propane gas and propane
tank(s).
Use this heater only with a propane vapor
withdrawal supply system. See Chapter 5
of the Standard for Storage and Handling of
Liqueed Petroleum Gas, ANSI/NFPA 58 and/
or CAN/CGA B149.2. Your local l brary or re
department will have this booklet.
This heater will operate with a 20 lb (9.07 kg)
propane tank. However, you can only oper-
ate it in the LOW position during mildly cool
weather for a very short time. At higher heat
settings or during colder weather, you must
use larger tanks.
The amount of propane gas ready for use from
propane tanks varies. Two factors decide this
amount.
1. The amount of propane gas in tank(s)
2. The temperature of tank(s)
The chart below shows the minimum num-
ber of 100 b (45 kg) tanks needed to run
the heater. Connect tanks together with a
manifold.
Average Temperature Number
At Tank Location Of Tanks
(80,000 Btu/Hr models)
20° F (-6.7° C) to 60° F (15.6° C) 1
0° F (-17.8° C) to 20° F (-6.7° C) 2
(200,000 Btu/Hr models)
20° F (-6.7° C) to 60° F (15.6° C) 2
0° F (-17.8° C) to 20° F (-6.7° C) 3
Less gas is vaporized at lower temperatures.
Your local propane gas dealer will help you
select the proper supply system.
INSTALLATION
WARNING: Review and un-
derstand the warnings in the
Safety section, page 2. They are
needed to safely operate this
heater. Follow all local codes
when using this heater.
CAUTION: Never ignite and/
or run this heater unless the
shells are fully extended and
locked into position.
CAUTION: Not intended
for use on nished oors. This
includes, but is not limited to
carpet, rugs, vinyl, treated and
synthetic wood ooring.
Tools Required:
• 7/8" wrench
• 3/4" wrench (or adjustable wrench)
• #1 Phillips screwdriver
OUTER SHELL
IMPORTANT: When the heater is rst re-
moved from carton, the outer shell is in the
down position. Protect hands before lifting
outer shell. Never grasp bare metal without
hand protection.
1. Care must be taken to protect hands dur-
ing this step. Lift outer shell straight up
as shown in Figure 2, until all three clips
engage slots in lower shell. Screw holes
will line up at this point.
2. Lock clips into place with 1 screw each as
shown in Figure 2. The heater must not be
operated unless the outer shell is properly
extended and fully locked into place.

www.desatech.com
121512-01C 5
Off/
Apagado/
Arrêt
Lo/Bajo/
Bas
Med/
Medio/
Moyen
Hi/Alto/
Haut
Figure 3 - Regulator Position
Propane
Tank
Propane Supply
Valve
Regulator
Hose
POL
Fitting
INSTALLATION
Continued
Figure 4 - Hose and Valve Inlet
(200,000 Btu/Hr Model Shown)
Hose Valve Inlet
OPERATION
CONNECTING TO GAS SUPPLY
WARNING:Testallgaspiping
and connections for leaks after
installation or servicing. Never
use an open ame to check for
a leak. Apply a mixture of liquid
soap and water to all joints.
Bubbles forming show a leak.
Correct all leaks at once.
1. Provide propane supply system (see
Propane Supply, page 4).
2. Connect fuel gas tting on hose/regulator
assembly to propane tank(s). Turn fuel
gas tting counterclockwise into threads
on tank. Tighten rmly using a wrench.
IMPORTANT: Tighten regulator with vent
pointing down. Pointing vent down pro-
tects regulator from weather damage.
3. Connect hose to the valve inlet. Tighten
rmly using a wrench. You must use the
regulator supplied with heater even if
propane tank has one.
4. Open propane supply valve on propane
tank(s) slowly. Note: If not opened slowly,
excess-ow check valve on propane tank
may stop gas ow. If this happens, you may
hear a click inside the regulator assembly,
this is the check valve closing. To reset the
excess ow check valve, close propane
supply valve and open again slowly.
5. Check all connections for leaks. Apply
mixture of liquid soap and water to gas
joints. Bubbles forming show a leak that
must be corrected.
Figure 5 - Control Knob and Piezo Ignitor
Piezo Ignitor Button
Control Knob
WARNING: Review and un-
derstand the warnings in the
Safety section, page 2. They are
needed to safely operate this
heater. Follow all local codes
when using this heater.
80,000 BTU/HR HEATER
TO START HEATER
1. Follow all installation, ventilation and
safety information.
2. Locate heater on stable and level surface.
Make sure strong drafts do not blow on
heater.
3. Make sure unit is turned off by slightly
pressing and turning control knob fully
clockwise to OFF.

www.desatech.com 121512-01C6
4. Open propane supply valve on propane
tank(s) slowly. Note: If not opened slowly,
excess-ow check valve on propane tank
may stop gas ow. If this happens, you
may hear a click inside the regulator as-
sembly, this is the check valve closing. To
reset the excess ow check valve, close
propane supply valve and open again
slowly.
5. Slightly press and turn control knob
counterclockwise to the LO position (see
Figure 5).
6. With the control knob pushed all the way
in, press and release the piezo ignitor
button. Keep pressing piezo ignitor but-
ton until the burner lights. Hold control
knob down for a maximum of 15 seconds
while attempting ignition. If heater does
not ignite, release control knob and wait
3 minutes before attempting to reignite.
7. After ignition, hold control knob down
for about 30 seconds. This activates the
automatic control system.
8. When burner remains lit, set heater at the
desired heat level by slightly depressing
the control knob and turning it counter-
clockwise to the MED or HI settings (see
Figure 5, page 5).
9. If burner goes out, turn off gas. Slightly de-
press and turn control knob fully clockwise
to OFF. Check fuel supply. If adequate
fuel is available, restart heater beginning
at step 1, page 5.
CAUTION:Always runheater
with control knob at LO, MED or
HI settings. Never set control
knob between OFF, LO, MED or
HI settings.
TO STOP HEATER
1. Tightly close propane supply valve on
propane tank(s). Allow heater to burn
remaining fuel in hose.
2. Shut off burner. Do this by pushing in the
control knob and turning clockwise to the
OFF position.
TO RESTART HEATER
1. Wait ve minutes after stopping heater.
2. Restart heater by following To Start
Heater,page 5.
OPERATION
Continued
200,000 BTU/HR HEATER
TO START HEATER
1. Before lighting pilot fully close the ball
valve (turn knob fully clockwise).
2. Fully open the valve on the propane
cylinder and wait 15 seconds before
proceeding to step 3.
3. Press red button on safety pilot valve
admitting gas to the heater. Then push
and release the ignitor button until the
pilot lights.
4. When the pilot lights, continue to hold the
button depressed for 30 seconds, then
release.
5. If pilot goes out, wait 5 minutes and repeat
the lighting procedure.
6. When the pilot remains lit, open the ball
valve (turn knob counterclockwise) to
light main burner. Partially close valve to
regulate heat output.
Figure 6 - Starting Heater
Ignitor
Button
Ball Valve Control
Knob Button
TO STOP HEATER
1. Securely close valve on the propane
cylinder.
2. Continue to operate heater until all fuel in
the hose has burned.
3. Fully close the ball valve.
TO RESTART HEATER
1. Securely close valve at propane cylinder.
2. Wait 5 minutes.
3. Restart heater by following To Start
Heater.
Safety Pilot
Valve

www.desatech.com
121512-01C 7
STORAGE
2. Before each use, check the soft "O" ring
seat at the bullnose of the POL tting. If
the "O" ring is cut, scuffed or otherwise
damaged, replace the POL tting with part
number LPA4020.
3. Turn off the gas at the propane/LP gas supply
cylinder(s) when the heater is not in use.
4. Heater is to be stored indoors. The con-
nection between propane/LP gas supply
cylinder(s) and heater must be disconnect-
ed, cylinder(s) removed from the heater
and stored outdoors in accordance with
Chapter 5 of the Standard for Storage and
Handling of Liqueed Petroleum Gases
ANSI/NFPA 58 and CSA B149.1, Natural
Gas and Propane Installation Code.
5. Store in a dry, clean and safe place.
MAINTENANCE
CAUTION:Disconnectheater
from propane supply tank(s).
CAUTION: Be careful not to
locate ngers in groves on side
of heater, in vent holes or on
bottom of shell when collaps-
ing shell to the down position.
Severe cuts may occur. Always
wear hand protection when
grasping bare metal.
1. The heater should be inspected before
each use and at least annually by a quali-
ed person.
WARNING: Never attempt
to service heater while it is
connected to propane supply,
operating or hot. Severe burns
can occur.
1. Keep heater clean.
2. Inspect heater before each use. Check
connections for leaks. Apply mixture of
liquid soap and water to connections.
Bubbles forming show a leak that must
be corrected. Correct all leaks at once.
3. Inspect hose/regulator assembly before
each use. If hose is highly worn or cut,
replace.
4. Have heater inspected yearly by a quali-
ed service person.

www.desatech.com 121512-01C8
TROUBLESHOOTING
WARNING: Never service heater while it is plugged in, connected
to propane supply, operating or hot. Severe burns and electrical
shock can occur.
REMEDY
1. Open propane supply valve
slowly
2. Close propane supply valve
on propane tank and re-
open slowly
3. Replace burner orice
4. Check to assure ignitor
electrode gap is 0.195"
Check wire lead for dam-
age. Replace piezo ignitor
and/or ignitor electrode as
necessary
5. Clean or replace pilot as-
sembly
1. Relight, hold automatic
control valve button in 45
seconds
2. Check propane tank(s) for
proper gas supply
3. Tighten connection or re-
place thermocouple
4. Replace automatic control
valve
1. Turn valve counter clock-
wise to HIGH
2. Replace gas orice
3. Check gas supply; check
regulator output
4. Consult propane gas sup-
plier
OBSERVED FAULT
Burner fails to light
Pilot lights but goes out when
automatic control valve button
is released (200,000 Btu/Hr
models only)
Burn rate is low
POSSIBLE CAUSE
1. Propane supply valve
closed on propane tank(s)
2. Excess flow check valve
closed
3. Blockage in burner orice
4. Piezo ignition system not
sparking
5. Pilot orice clogged
(200,000 Btu models only)
1. Not enough warm up time
2. Low gas pressure
3. Thermocouple loose or
needs to be replaced
4. Automatic control valve
needs to be replaced
1. Control valve is on LOW
2. Plugged gas orice
3. Low gas pressure
4. Low fuel supply

www.desatech.com
121512-01C 9
REPLACEMENT PARTS
Note: Use only original replacement parts.
This will protect your warranty coverage for
parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040.
When calling DESA Heating, LLC, have
ready:
• your name
• your address
• model and serial numbers of your heater
• how heater was malfunctioning
• purchase date
Usually, we will ask you to return the part to
the factory.
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040 for
referral information. A list of authorized dealers
can be found by visiting www.desatech.com.
When calling DESA Heating, LLC, have
ready:
• model and serial numbers of your heater
• the replacement part number
SPECIFICATIONS
TECHNICAL SERVICES
You may have further questions about installa-
tion, operation, or troubleshooting. If so, con-
tact DESA Heating, LLC at 1-866-672-6040.
When calling please have your model and
serial numbers of your heater ready.
You can also visit DESA Heating, LLC’s web
site at www.desatech.com.
ACCESSORIES
Purchase these accessories from your local
dealer. If they can not supply these accessories
call DESAHeating, LLC at 1-866-672-6040 for
information. You can also write to the address
listed on the back page of this manual.
80,000 BTU/HR
• Rating: 40,000 - 80,000 Btu/hr (11.72
- 23.4 kW)
• Type of Gas: Propane/LP Only
• Gas Supply Pressure to regulator: Maxi-
mum - Bottle Pressure, Minimum - 5 psig
(34.5 kPa)
• Gas Supply Pressure regulator out:
19" W.C. (48 cm)
• Ignition: Piezo Ignitor
• Minimum Ambient Temp Rating:
0° F (-17.8° C)
• Fuel Consumption/hr: 1.85 - 3.71 lb
(0.83 – 1.68 kg)
• Fuel Orice Port No.: 6
• Fuel Orice Port Size: 0.04" (1.02 mm)
200,000 BTU/HR
• Rating: 75,000 - 200,000 Btu/hr (22.0
- 58.6 kW)
• Type of Gas: Propane/LP Only
• Gas Supply Pressure to regulator: Maxi-
mum - Bottle Pressure, Minimum - 15 psig
(103 kPa)
• Gas Supply Pressure regulator out:
10 psig (68.9 kPa)
• Ignition: Piezo Ignitor
• Minimum Ambient Temp. Rating: 0° F (-
17.8° C)
• Fuel Consumption/hr: 3.48 - 9.28 b
(1.58 - 4.21 kg)
• Fuel Orice Port No.: 6
• Fuel Orice Port Size: 0.032" (0.813 mm)

www.desatech.com 121512-01C10
PARTS
MODELS TC106A, TC112A, TC113A, TC114A AND TC115A
1
2
3
10
15
6
8
12
9
18
17
19
20
5
11
7
16
4
14
13

www.desatech.com
121512-01C 11
PARTS
MODELS TC106A, TC112A, TC113A, TC114A AND TC115A
This list contains replaceable parts used in your heater. When ordering parts, follow the
instructions listed under Replacement Parts on page 9 of this manual.
KEY
NO. PART NO. DESCRIPTION QTY.
1 113785-01 Cap 1
2 113781-01 Upper Shell 1
3 113825-01 Lower Shell 1
4 113778-01 Ring Shield 1
5 ** Base 1
6 116617-01 Ignitor Electrode 1
7 113777-02 Burner Ring Assembly 1
8 113790-01 Thermocouple 1
9 100898-01 Thin Hex Nut 2
10 102445-01 Piezo Ignitor Kit 1
11 098508-01 Valve Retainer Nut 1
12 121326-01 Control Knob 1
13 123632-01 Heat Shield 1
14 123631-01 Fuel Tube Assembly Kit 1
15 121992-01 Hose/Regulator Assembly, 10 foot 1
16 121513-01 Orice, LP 1
17 099460-01 Brass Hex Cap 1
18 116554-01 Automatic Valve 1
19 117059-01 Adapter, 1/4 FPT x 1/4 MPT 2
20 113795-01 Female Elbow Fitting, 1/4 FPT x 3/8 FLR 1
PARTS AVAILABLE - NOT SHOWN
117069-02 80,000 Btu/Hr Rating Decal 1
113808-07 Hang Tag (English) 1
113808-08 Hang Tag (Spanish) 1
113808-09 Hang Tag (French) 1
113805-04 Installation Decal (English) 1
113805-05 Installation Decal (Spanish) 1
113805-06 Installation Decal (French) 1
113802-29 Model Decal 1
116558-01 Control Position Decal 1
**Not a eld replaceable part

www.desatech.com 121512-01C12
3
10
24
23
8
4
13
15
5
19
14
22
20
16
17
25
1
26
2
21
11
9
27
29
6
23
12
7
18
PARTS
MODELS 200C, RCP200V(A), SPC-200C, TC107 AND TC200V(A)

www.desatech.com
121512-01C 13
PARTS
MODELS 200C, RCP200V(A), SPC-200C, TC107 AND TC200V(A)
This list contains replaceable parts used in your heater. When ordering parts, follow the
instructions listed under Replacement Parts on page 9 of this manual.
KEY
NO. PART NO. DESCRIPTION QTY.
1 113814-01 Pilot Assembly 1
2 113835-01 Hose/Regulator Assembly 1
3 113777-01 Burner Ring Assembly 1
4 113778-01 Ring Shield 1
5 113779-01 Fuel Tube Assembly 1
6 113780-01 Pilot Tube Assembly 1
7 114178-01 Upper Shell 1
8 113782-01 Orice Adapter 1
9 113783-01 Bracket, Pilot Mounting 1
10 113816-01 Orice, LP 1
11 ** Base 1
12 113785-01 Cap 1
13 100898-01 Thermocouple Clip Thin Hex Nut 2
14 113787-01 Control Valve 1
15 113788-01 Female Elbow Fitting, 1/4 FLR x 1/8 FPT 1
16 113817-01 Female Elbow Fitting, 1/4 FLR x 1/4 FPT 1
17 113790-01 Thermocouple 1
18 113821-01 Lower Shell 1
19 113812-01 Fitting, 1/4 FPT x 1/4 MPT 1
20 113793-01 Ball Valve 1
21 102445-01 Piezo Ignitor Kit 1
22 113794-01 Valve Nut, 1/2-28 1
23 113795-01 Female Elbow Fitting, 1/4 FPT x 3/8 FLR 3
24 113796-01 Retaining Ring 1
25 113797-01 Ignitor Electrode 1
26 113798-01 Heat Shield 1
27 115364-02 Pilot Orice 1
28 113801-01 Elbow Fitting, 1/8 FPT x 1/4 CPSN 1
PARTS AVAILABLE - NOT SHOWN
113809-01 Ball Valve Knob 1
113810-01 Ball Valve Knob Insert 1
117069-03 200,000 Btu/Hr Rating Decal 1
113808-01 Hang Tag (English) 1
113808-02 Hang Tag (Spanish) 1
113808-03 Hang Tag (French) 1
113805-01 Installation Decal (English) 1
113805-02 Installation Decal (Spanish) 1
113805-03 Installation Decal (French) 1
113802-19 Model Decal 1
**Not a eld replaceable part

121512-01
Rev. C
05/08
DESA Heating, LLC
2701 Industrial Drive
Bowling Green, KY 42101
www.desatech.com
1-866-672-6040
WARRANTY
KEEP THIS WARRANTY
DESA HEATING, LLC LIMITED WARRANTIES
New Products
Standard Warranty: DESA Heating, LLC warrants this new product and any parts thereof to be free from
defects in material and workmanship for a period of one (1) year from the date of rst purchase from an
authorized dealer provided the product has been installed, maintained and operated in accordance with
DESA Heating, LLC’s warnings and instruc ions.
For products purchased for commercial, industrial or rental usage, his warranty is limited to 90 days from
the date of rst purchase.
Factory Reconditioned Products
Limited Warranty: DESA Heating, LLC warrants factory reconditioned products and any parts thereof
to be free from defects in material and workmanship for 30 days from the date of rst purchase from an
authorized dealer provided the product has been installed, maintained and operated in accordance with
DESA Heating, LLC’s warnings and instruc ions.
Terms Common to All Warranties
The following terms apply to all of the above warranties:
Always specify model number and serial number when contac ing the manufacturer. To make a claim under
this warranty the bill of sale or other proof of purchase must be presented.
This warranty is extended only to the original retail purchaser when purchased from an authorized dealer,
and only when installed by a qualied installer in accordance with all local codes and instructions furnished
with this product.
This warranty covers the cost of part(s) required to restore this product to proper operating condition and
an allowance for labor when provided by a DESA Heating, LLC Authorized Service Center or a provider
approved by DESA Heating, LLC. Warranty parts must be obtained through authorized dealers of this prod-
uct and/or DESA Heating, LLC who will provide original factory replacement parts. Failure to use original
factory replacement parts voids this warranty.
Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty
repairs, unless expressly covered by this warranty, are not reimbursable under this warranty and are the
responsibility of the owner.
Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents,
improper installation, lack of proper maintenance, tampering, or altera ion(s).
This is DESA Heating, LLC’s exclusive warranty, and to the full extent allowed by law; this express warranty
excludes any and all other warranties, express or implied, written or verbal and limits he duration of any
and all implied warranties, including warranties of merchantability and tness for a particular purpose to one
(1) year on new products and 30 days on factory recondi ioned products from the date of rst purchase.
DESA Heating, LLC makes no other warranties regarding this product.
DESA Heating, LLC’s liability is limited to the purchase price of the product, and DESA Heating, LLC shall
not be liable for any other damages whatsoever under any circumstances including indirect, incidental, or
consequential damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specic legal rights, and you may also have o her rights which vary from state to state.
For information about this warranty contact:
Model ( located on product or identication tag )_____________________________
Serial No. ( located on product or identication tag )__________________________
Date Purchased __________________________
Keep receipt for warranty verication.
82 Akron Road
Toronto, Ontario M8W 1T2
[phone]