DeviceWell HDS7106 User manual

Website: www.devicewell.com Email: [e-mail] 1
HDS7106
SWITCHER
Model: HDS7106
VER 1.0
Users’ Manual
HD

Website: www.devicewell.com Email: [e-mail] 2
HDS7106
Contents
1. Overview ........................................................................................................................... 3
1.1 Introduction ........................................................................................................ 3
2. Functional characteristics.................................................................................................. 4
3. Software panel partition introduction .............................................................................. 5
4. Software operation instructions........................................................................................ 6
4.1 Audio Control Area ............................................................................................. 6
4.2 Transition Effect Control Area ............................................................................ 9
4.3 PGM & PVW Selection ...................................................................................... 11
4.4 Switching table putter ...................................................................................... 15
4.5 Integrated Control Area.................................................................................... 16

Website: www.devicewell.com Email: [e-mail] 3
HDS7106
1. Overview
1.1 Introduction
DeviceWell HD Video Switcher HDS7106 adopts portable integrated design, metal shell,
small size and light weight, standard size: 255mm*160mm*60mm, which can be used for video
special effects switching in small outdoor scenes. The device integrates common components
such as multiview processor, special effects generator, audio processor, and control keyboard.
The HDS7106 supports 4 channels of broadcast SDI and 2 channels of HDMI for a total of
six video signals. The external preview signal can be output synchronously. The HDS7106
supports SDI embedded audio + external analog audio. After mixing, it can be embedded in the
output SDI signal or output from the analog port. The resolution of all input signals is
automatically adapted, and the output signal resolution can be selected as required, which is
quite flexible. For the video switching needs of broadcast TV, outdoor sports events, school
courseware production, etc., the functions of HDS7106 can be fully satisfied.

Website: www.devicewell.com Email: [e-mail] 4
HDS7106
2. Functional characteristics
The DeviceWell HDS7106 6-channel HD video switcher is a multi-function switcher that requires
no special knowledge and can be used for video switching and audio mixing with simple operation.
This unit can be used in radio and television, live broadcast and various activities.
◆Portable integrated design
◆Advanced black metal body, high strength
and light weight
◆Integrated control keyboard
◆Supports up to 4 SDI and 2 HDMI inputs
◆3.5mm analog audio input and output
◆1-channel lotus seat audio input and output
◆Support PIP/POPscreen windowing function
◆Audio support follow and mix assignment
mode
◆Support 1 channel SDI output custom
PGM/PVW
◆PGM output: 2-CH SDI and 1-channel
HDMI
◆Multiview output: 1 CH HDMI and 1 CH
SDI
◆Support special effects switching such as
MIX / FADE
◆Support CUT hard support for AUTO effect
switching
◆Support Tally / network remote control
◆Built-in chassis temperature detection and
fan intelligent control system
◆Support software online upgrade

Website: www.devicewell.com Email: [e-mail] 5
HDS7106
After opening the software, you can see the entire layout of the button panel, as shown below.
NO.
Name
Description
1
Audio Control
Mainly for Audio Follow and mix settings.
2
Transition Effect Control
Select transition effects
3
PVW& PGM Select
Live broadcast and preview selection
4
T-Bar
Manual control of transitions
5
PVW& PGM Select
Live broadcast and preview selection
1
2
5
3
4

Website: www.devicewell.com Email: [e-mail] 6
HDS7106
4.1 Audio Control Area
How to use the audio follow mode:
1、Press the AFV (Follow) button on the operation panel, the AFV button will light
blue at this time, indicating that the audio follow mode is turned on.
2、The channels of the audio follow mode are IN1-SDI1, IN2-SDI2, IN3-SDI3, IN4-SDI4, IN5-HDMI5,
and IN6-HDMI6.
When the signal source of the PGM 1 channel is pressed (the button displays red), CH1 also
corresponds to the IN1 signal source (indicating that the current sound is from the IN1-SDI1
channel). As shown below

Website: www.devicewell.com Email: [e-mail] 7
HDS7106
3、If you need to adjust the audio output volume, you can adjust the audio volume by adjusting
the VOL1 volume progress bar on the right side. The more you slide to the right, the louder the
volume. As shown below
Note: CH2 and VOL2 are not operational at this time.
●How to use the mix assignment:
1、Press the MIX button on the operation panel. The MIX button will light blue at this
time, indicating that the audio mix mode is turned on.As shown below

Website: www.devicewell.com Email: [e-mail] 8
HDS7106
2、At this time, you can arbitrarily assign two channels of audio for mixing operation through the
CH1 and CH2 buttons (you can do a pull-down selection). The channels assigned by the mix are
IN1-SDI1, IN2-SDI2, IN3-SDI3, IN4-SDI4, IN5-HDMI5, IN6-HDMI6, XLR_IN, RCA_IN. Under the mix
assignment mode, there are two additional audio add-on functions. Audio interface such as RCA.
As shown below
3、If you need to adjust the audio output volume, you can adjust the audio volume by adjusting
the VOL1 and VOL2 volume progress bars on the right side. The more you slide to the right, the
louder the volume. As shown below
3.5mmAudio Interface
RCAAudio Interface

Website: www.devicewell.com Email: [e-mail] 9
HDS7106
4.2 Transition Effect Control Area
There are 3 transition modes:
MIX transitions, FADE, and Wipes, where the Wipes include: up, down, left, and right.
In the six transition modes, one transition mode can be arbitrarily selected for transition
switching. As shown below
MIX Transition
The MIX effect is a transition effect. After setting the transition, the original live screen will
be lightened at the main output and then know that the transition to the new live screen is
complete.
Click on the effect control area (press the blue light afterwards), and then click or use
the fader orAUTO to switch. The effect is as follows.
FADE Transition
Click on the effect control area (press the blue light afterwards), and then click or use
the fader orAUTO to switch, under the effect diagram.
MIX transition effect, superimposed and superimposed B
picture in A picture until the transition to the end, the
picture is completely replaced with B picture

Website: www.devicewell.com Email: [e-mail] 10
HDS7106
Four special effects wipe transitions
There are 4 types of wipe transition modes: up/down/left/right.
Up transition: Click on the effect control area (press the blue light afterwards), and then
click or use the T-bar or AUTO to switch. The effect is as follows.
Down transition: Click on the effect control area (press the blue light afterwards), and
then click or use the T-bar or AUTO to switch. The effect is as follows.
Left Transition: Click on the effect control area (press the blue light), then click or use
the T-Bar orAUTO to switch. The effect is as follows.
FADE in and out, and A gradually darkens until it is completely black,
and then gradually changes from black to B.
Up transition effect, the A picture is unchanged, and the B picture is
gradually drawn in the upward direction until the picture completely
becomes B.
Downward transition effect, the A picture is unchanged, and the B picture is
gradually drawn in the downward direction until the picture
completely becomes B.

Website: www.devicewell.com Email: [e-mail] 11
HDS7106
Right transition: Click on the effect control area (press the blue light), then click or use
the fader orAUTO to switch. The effect is as follows.
4.3 PGM & PVW Selection
You can switch between the 1-6 channel screens by switching the PGM and PVW of the deck in
the software, as shown in the figure below.
Left transition effect, theA picture is unchanged, and the B picture is gradually drawn
in the left direction until the picture completely becomes B.
Right transition effect, the A picture is unchanged, and the B picture
is gradually drawn in the right direction until the picture completely
becomes B.

Website: www.devicewell.com Email: [e-mail] 12
HDS7106
Multiview output window introduction
PVW and PGM are the preview and live output respectively, as shown below.
There are 6 windows below which correspond to input source monitoring, corresponding to
buttons 1 –6 on the control panel of the switcher.
PVW
PGM

Website: www.devicewell.com Email: [e-mail] 13
HDS7106
PGM & PVW Output Signal
When the switcher software control panel is opened, 1 (PGM) and 2 (PVW) in the
button panel will light red and green respectively, and the live and preview signals in
the output multi-screen monitor are 1 (PGM). ) and 2 (PVW), the signal sources are
SDI IN1 and SDI IN2, respectively.
The effect chart is as follows
PGM & PVW Source Switching
If you want to switch between PGM and PVW source in Multiview
Suppose you want to convert live signal source 1 (PGM) and preview source 2 (PVW) into 2
(PGM) and 1 (PVW) in multiple pictures, just press 2 (PGM) and 1 in the button panel ( PVW),
then use the T-bar to switch. The live PGM signal source 1-6 can be arbitrarily switched with the
preview PVW signal source.
1
2
2
1

Website: www.devicewell.com Email: [e-mail] 14
HDS7106
The effect chart is as follows:
You can also switch between the PGM1-6 signal and the PVW1-6 signal in the button panel.
1
2
2
1

Website: www.devicewell.com Email: [e-mail] 15
HDS7106
4.4 Switching table putter
Open the software control panel to see the AUTO, CUT and putter sections in the middle. This
section controls the switcher's transition operation. The effect is as follows.
When operating the software control panel's audio control area, transition control area, and PGM
and PVW control areas, you need to switch by pressing the AUTO/CUT/Pusher.
When the AUTO or CUT button is pressed after confirmation, the button will display a red light,
indicating that the switch is complete.

Website: www.devicewell.com Email: [e-mail] 16
HDS7106
4.5 Integrated Control Area
In the software control panel, you can also use the PIP picture-in-picture and POP picture-out
functions. The picture is displayed as shown below.

Website: www.devicewell.com Email: [e-mail] 17
HDS7106
PIP picture-in-picture special effects operation
Press the PIP button in the software control panel, the button will display a blue light, indicating
that the picture-in-picture function is enabled. At this time, you can make a drop-down selection
in the border switch, border width, border color and display screen size, as shown below.
POP picture painting special effects operation
Under the PIP button in the software control panel, the button will display a blue light, which
means that the picture-in-picture function is enabled. At this time, you can make a drop-down
selection in the border switch, border width, border color and display screen size, as shown in
the figure below.

Website: www.devicewell.com Email: [e-mail] 18
HDS7106
Output resolution adjustment
When the S-Type button is selected, the resolution of the output screen can be adjusted, as
shown in the figure below.