DeviceWell SDI 10-Screen Multiview User manual

Website: www.devicewell.com Email: su[email protected]
SDI 10-Screen Multiview
Model: MVP9110
VER 10
Users’ Manual

I
Precautions
To ensure the reliability, use and safety of the equipment, please observe the following
when installing, using and maintaining:
Before the device is powered on, it is necessary to check to ensure that the chassis is well
grounded to prevent electrostatic discharge from the chassis and endanger the equipment and
personal safety, and to provide good shielding effect.
◆Do not place system equipment in a location that is too cold or too hot.
◆The power supply of the device will generate heat during operation, so keep the working
environment well ventilated to avoid damage to the device due to excessive temperature.
◆Turn off the main power switch when it is rainy or wet or when it is not used for a long
time.
◆Non-professionals, please do not try to open the equipment case without permission, and do
not repair it yourself to avoid accidents or damage to the equipment.
◆Do not spill any chemicals or liquids on or near the equipment.

II
Contents
1. Product Introduction............................................................................................................ 1
1.1. Product Overview.....................................................................................................1
1.2. Main Functions.........................................................................................................1
1.3. Product Parameters...................................................................................................2
1.4. Standard List.............................................................................................................3
2. Operation and Function Description...................................................................................4
2.1. Equipment operation.................................................................................................4
2.2. Multi-screen Mode Description................................................................................4
2.2.1. 1-screen mode ................................................................................................5
2.2.2. 4-screen mode ................................................................................................6
2.2.3. 6-screen mode ................................................................................................6
2.2.4. 8-screen mode ................................................................................................7
2.2.5. 9-screen mode ................................................................................................7
2.2.6. 10-screen mode ..............................................................................................8
2.3. Keypad Operation Instructions.................................................................................8
2.3.1. Channel switching operation..........................................................................8
2.3.2. Full Panel........................................................................................................8
2.3.3. Mode...............................................................................................................9
2.3.4. Reso................................................................................................................9
2.3.5. Audio..............................................................................................................9
2.3.6. Char................................................................................................................9
2.4. LCD function............................................................................................................9
2.5. Function capture ....................................................................................................... 9
2.5.1. Single-screen zoom function........................................................................10
Audio video can be output at the same time, characters can be added arbitrarily,
drag in different positions.........................................................................................10
2.5.2. 4- screen resolution change..........................................................................10
2.5.3. 6-screen No signal input............................................................................... 11
2.5.4. 8- Screen....................................................................................................... 11
2.5.5. 10-screen ......................................................................................................12

III
2.6. 10-screen character setting control software description........................................12
2.6.1. Open the software.........................................................................................13
2.6.2. Controlling device........................................................................................13
2.6.3. Right click menu bar....................................................................................14
2.6.4. Single screen display function......................................................................16
2.6.5. Display screen switching function ...............................................................16
2.7. Menu usage and LCD display instructions.............................................................17
2.7.1. Boot LCD status...........................................................................................17
2.7.2. Menu.............................................................................................................17
2.8. Tally Function.........................................................................................................21
2.9. REST Reset.............................................................................................................21
2.10. Dual power supply..................................................................................................21
3. Failure and Maintenance...................................................................................................22
3.1. Common Faults and Solutions................................................................................22
3.2. Maintenance............................................................................................................22
3.3. Warranty information..............................................................................................22

Website: www.devicewell.com Email: su[email protected]
1
1. Product Introduction
1.1. Product Overview
This is a professional-grade SDI picture splitter that supports 10-CH SDI inputs, 2-CH
HDMI inputs, and 2-CH AV inputs. 2-CH SDI+3-CH HDMI output. You can change the
display resolution to 1080i50 / 60, 1080p25 / 30 or even more using the front panel keyboard.
The device is a multi-screen splitter with 10-way matrix switching. The device can connect 10
SDI signals. When performing multi-picture synthesis, there are 2 identical SDI outputs (the
two left SDI interfaces) and 3 HDMI outputs. The display mode of the screen can be flexibly
configured through the network port using PC software. , can be configured for 1~10 screens.
And the device supports SDI audio column display and character overlay function. The device
integrates SDI input/output interface and control interface, which can conveniently process
SDI signals for picture segmentation, signal delay, frequency conversion processing, and
frame synchronization. The device supports network, RS422 and button control, and supports
network interface to update internal software, which can realize more functions and simple
operation.
1.2. Main Functions
◆Art design style
◆Up to 10 signal inputs, up to 10 signal outputs
◆Support single screen enlargement, 4 screens, 6 screens, 9 screens, 10 screen modes
◆Support input screen switching
◆Support audio column display, audio de-embedding and embedding, optional any input
audio plus embedded output
◆Chinese and English character overlay (character color can be changed)
◆Input port: SDI ×8; HDMI ×2;
◆Output port: SDI ×2; HDMI ×3
◆Input support matrix switching function
◆SDI HD/SD Adaptive

Website: www.devicewell.com Email: su[email protected]
2
◆Support network, RS422 and button control
◆Support network upgrade system function
◆Support for later extension
◆Support TALLY function
◇Special features can be customized
1.3. Product Parameters
Name
SDI HD 10-Screen Multiview
SDI Input
Input Signal
SDI HD serial digital video signal
Rate
143Mbps~2.97Gbps
Connector
BNC complies with IEC169-8
Reflection loss
>15dB 5MHz~3GHz
Signal amplitude
800mV±10%
Impedance
75Ω
Balance
100m Belden 1694A HD
200m Belden 8281A HD
SDI Output
Output Signal
SDI HD serial digital video signal
Connector
BNC complies with IEC169-8
Reflection loss
>15dB 5MHz~3GHz
Signal amplitude
800mV±10%
Impedance
75Ω
Up/Down time
0.6ns±100ps
DC offset
0V±0.5V
Clock recovery
Auto output optional
Overshoot
<5%
Jitter
<0.2Ul

Website: www.devicewell.com Email: su[email protected]
3
1.4. Standard List
Multiview main part
AC power cord x 1
Control software x1
User Manual x1
HDMI Output
Output Signal
Standard HDMI signal
Rate
270Mbps~2.97Gbps
Signal amplitude
800mV±10%(100R)
Impedance
100Ω
Control
Parameter
Local control
button (front panel)
Serial control
RS422
Connection port
RJ45 standard network interface (UDP/HTTP)
Control software
WINDOWS (customizable IOS/Android)
Optional components
Central control keyboard
General
Parameters
Power supply
100-240V/AC 50/60Hz
Power Rating
25W-150W, According to host type
Size
1U(standard power supply )
Control Panel
YES
Weight
2.1KG
Operating
Temperature
0℃~50℃without condensation
Storage Temperature
-20℃~75℃
Working Humidity
20%~70%RH
Storage Humidity
0%~90%RH, No condensation

Website: www.devicewell.com Email: su[email protected]
4
2. Operation and Function Description
2.1. Equipment operation
Note: Please use the following installation sequence. If the installation sequence is
not followed correctly, the device may not work or work abnormally.
(1) Connect the signal output of the signal source to the input of the unit.
(2) Configure the corresponding I/O card according to the input and output of the
site.
(3) Connect the signal output of this unit to the signal input of the display unit.
(4) Turn on the power of the device and turn on the power button switch.
(5) Use the manual button to select the input and output ports.
(6) Rear panel interface description:
①SDI×2(Multi-screen output) ②HDMI x3(Multi-screen output)
③SDI×10 input ④RS422 interface
⑤REST Reset ⑥Power Indicator
⑦Network and USB interface ⑧AC 100 –240V
2.2. Multi-screen Mode Description

Website: www.devicewell.com Email: su[email protected]
5
2.2.1. 1-screen mode

Website: www.devicewell.com Email: su[email protected]
6
2.2.2. 4-screen mode
2.2.3. 6-screen mode

Website: www.devicewell.com Email: su[email protected]
7
2.2.4. 8-screen mode
2.2.5. 9-screen mode

Website: www.devicewell.com Email: su[email protected]
8
2.2.6. 10-screen mode
2.3. Keypad Operation Instructions
2.3.1. Channel switching operation
Switching operation can be performed according to the input signal and the multi-screen
window number. IN x OUT y (such as switching the 2nd signal to the 5th display, IN + 2 +
OUT + 5), you can also switch all the way at the same time. To multi-channel display, IN 2
OUT 1, 2, 3, 4.... If you want to switch 10 channels, press 10+ first, then press 0.
2.3.2. Full Panel

Website: www.devicewell.com Email: su[email protected]
9
In the multi-screen switching, you can select a certain way to display in full screen,
press the full screen window number + Full Panel (such as the full screen display of 5 screens
in the 16 screen: 5 + Full Panel), press the Full Panel button again to return In the
multi-picture state, if the channel switching operation has just been performed, the OUT is in
the light-on state, and it is necessary to first press OUT to turn off the light and then perform
full-screen operation.
2.3.3. Mode
Multi-screen mode switching, there are six modes of 1, 4, 6, 8, 9, 10 to select, you can
press the Mode button to cycle.
2.3.4. Reso
Output resolution setting, press the Reso button to switch between different output
resolutions, a total of 1080p60, 1080p50, 1080p30, 1080p25, 1080i50, 1080i60, 720p60,
720p50 eight resolution options.
2.3.5. Audio
Switch the display or hide of the audio columns of all channels.
2.3.6. Char
Switch between displaying or hiding the characters of all channels.
2.4. LCD function
When Mode is switched, the LCD will display the current multi-picture status, and the
number in the small grid represents the current input channel number.
When you perform a software upgrade, the status of the upgrade and the version
information of the program are displayed.
2.5. Function capture

Website: www.devicewell.com Email: su[email protected]
10
2.5.1. Single-screen zoom function
Audio video can be output at the same time, characters can be added arbitrarily, drag in
different positions.
2.5.2. 4- screen resolution change

Website: www.devicewell.com Email: su[email protected]
11
2.5.3. 6-screen No signal input
Any base map can be added, such as: company group photo logo
2.5.4. 8- Screen

Website: www.devicewell.com Email: su[email protected]
12
2.5.5. 10-screen
2.6. 10-screen character setting control software description

Website: www.devicewell.com Email: su[email protected]
13
2.6.1. Open the software
Run the exe file, click the "Search" button, you can list the device, the left mouse button
to select the corresponding device, you can read out the current device display mode and
characters, audio column status, as shown in Picture 1.
Picture 1
2.6.2. Controlling device
The control button area is roughly divided into two parts, as shown below
Note: This software will be continuously updated. If you need the latest software, please contact
us. The software version of this example is: ItemMove_16P_PcSet_r_v1.0.3.0_20170425.exe, the
software 10 screen is shared with our 16 screens.
ItemMove_16P_PcSet_r_v1.0.3.0_20170425.exe，该软件 10 画面与本公司 16 画面共用

Website: www.devicewell.com Email: su[email protected]
14
Zone 1: Radio button is only used as a switch display mode.
Zone 2: The Functions for the 3 buttons as follows:
(1) Switch the output resolution of multi-screen split
(2) Switch the channel of the output sound source
(3) Audio column button, operation and status with subtitle button
(4) The default configuration button clears all character settings and channel switching,
making it the exit mode.
(5) UMD button, click to turn UMD display on or off
(6) Change the face switch button, click to switch the screen display mode
2.6.3. Right click menu bar
The contents of the entire right button are as shown in Picture 3 below.

Website: www.devicewell.com Email: su[email protected]
15
Picture 3
All its functions are as follows
(1) Switching channels
The mouse pops up in that area, and any input channel is selected to switch the video of
the corresponding window to the selected channel.
(2) UDM display (character overlay)
Right click on the UDM display and click on “Character Customization” to pop up the
change character before entering the box.
Only English letters and Arabic numerals can be entered in the input box, and try to be
within 16 characters.
Click “Change” and the following words will appear in the schematic area.
At this point, the mouse moves to the green area, and the mouse changes to the shape of

Website: www.devicewell.com Email: su[email protected]
16
the four-directional arrow. Press the left mouse button to move within the area.
(As shown in the figure above, move within 4), then release the left mouse button to
change the position information of the character in real time.
Right-click on the UDM display and click "Close Single Character" to turn off the
character information of the current area.
Note: The character display of each multi-picture mode is independent. Switching mode
will only display the character information of the switched mode.
(3) Audio column switch
Right-audio column, click “On” or “Off” to switch the audio column of the corresponding
screen in real time. The bottom layer of the position is uniformly configured.
(4) Resolution switching
Right-resolution, select and click any resolution, ie switch the resolution of the output display
(5) Single channel amplification and reduction
Right-click one-way operation, click “Zoom in” to zoom in on the current channel for full
screen display. Conversely, if it is already in full screen mode, click “Restore” to switch back
to the original multi-picture mode.
2.6.4. Single screen display function
When you need to zoom in on a certain output channel in a multi-screen, you can press
the output channel number and press the ALL button to zoom in. (Example: Full screen
display of the third screen in the current 10 screens: 3+ ALL), the number of the output
channel can be turned on by turning on the character display switch. To return to the previous
multi-picture mode, press the Menu button to switch.
2.6.5. Display screen switching function
If you want to switch the current output screen, you can switch it according to the “X
input Y output” mode: “X” indicates the input channel number of 1~10, “Y” indicates the
output channel number of the current multi-screen, “Enter” Replaced by MON on the
keyboard, "out" is replaced by CAM on the keyboard (example: the current picture is 10