DeView BTP12H37V12L User manual

Instruction Manual
1/3” Day-Night All in One Color Camera with
AI Varifocal Lens & Cable Management Bracket
INTRODUCTION
The high resolution True Day/Night, all in one digital color cameras have been developed using the advanced technology of Digital
Signal Processing LSI (DSP) together with a interline transfer CCD.
This series of cameras is suitable for surveillance applications or an input device for an image processing system.
PRECAUTIONS
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. Refer servicing to qualified
service personnel.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking or shaking it. The camera could be damaged by improper handling or storage.
3. Never face the camera toward the sun.
Whether the camera is in use or not, never face it toward the sun. Do use cautiously when operating the camera in the vicinity of
spot lights or other bright lights and light reflecting objects.
4. Do not operate the camera beyond its temperature, humidity or power source ratings.
Do not use the camera in an extreme environment where high temperature or high humidity exists. Use the camera under
conditions where temperatures are within -10~+50, and humidity is below 80% RH.
5. Do not touch the CCD sensor directly with your fingers. If necessary, use soft cloth moistened with alcohol to wipe off the dust.
6. When the camera is not in use, keep the lens closed or lens cap attached to protect the CCD sensor.
Safety Advice
Don’t touch the CCD Chip with your fingers.
Use the camera only with the voltage as mentioned on the type plate.
Use a monitor with 75 ohm impedance.
Never open the camera. Otherwise warranty is void.
FEATURES
z1/3” Sharp / Sony High Res. IR Camera with External Focus Adjustment
zPlug & Play Installation - Compact Size + Sunshield + Cable Management Bracket
zEffective Range up to 40M with Low / Mid / High Level Selectable
zFlickerless, AGC, AES & BLC On/Off Selectable
zWith Tempered Glass - Split Glass Technology to Avoid IR Reflection for Option
z3.7-12mm AI Varifocal Lens with Removable IR-cut Filter (Option: 9-22mm Ai Varifocal Lens w/ Removable IR-cut Filter)
z0 Lux with Built-in IR-LED
z42x Built In IR LED
zVideo Cable with BNC Connector
zWeatherproof
INSTALLATION & OPERATION
1. Install Camera
Use the supplied screws (in the accessories bag), and secure the camera in position.
2. Adjust 2-Axis Bracket
Adjust the bracket while checking the view angle from the monitor. Loosen the X-Y screws and then adjust the 2-Axis
bracket (X-Y Axis) to get the desired viewing angle.
3. Focus Adjustment
Focus adjustment should be done with zoom focus at the same time. Use the screwdriver to adjust the zoom/ focus ratio
(from wide to tele or near to far).
NOTE: Focus adjustment position differs depending on model type.

4 . Remove the Controller Cap
Remove the controller cap using a coin to make adjustments.
(1) Auto Iris Level Adjustment
User needs to adjust the DC level especially for conditions described below:
¾If camera is facing a window but is placed in a relatively dark room.
¾If the subject background is extremely bright or dark.
¾If brightness of the picture on the monitor is incorrect.
Auto Iris Level
- (counterclockwise): To decrease the contrast
+ (clockwise): To increse the contrast
(2) Function Selection Switch
FL (Flickerless) If the camera is used with 50Hz fluorescent lighting, flicker may appear on the screen. In this case,
ch should be set to FL position and switched to OFF position under normal lighting.FL swit
AGC (Auto Gain Control) Set to AGC position, camera’s sensitivity is automatically increased when level of
ambient light drops. AGC function automatically controls signal gain to a maximum of 28dB.
AES (Auto Electronic Shutter) Set to OFF mode for auto iris control and AES mode for fixed or manual iris
control (The default is OFF mode, this option is not applicable for units fitted with a DC iris lens)
BLC (Back Light Compensation) This function set to BLC position, is useful when the camera is facing an object
that has excessive light behind it (Ex.: Camera installed facing the doorway).
(3) IR Distance Adjustment
Installer may use IR adjustment function according to installation conditions. It is suggested that the view angle
should be checked before setting up the IR distance.
Table below is the suggested LED brightness and IR distance adjustment:
LED
Brightness IR Distance Focal Length
H (High) 25m~40m 9~22mm
M (Middle) 15m~25m 6~12mm
L (Low) 10m~15m 3.7~6mm
5. Install Sunshield
To install the sunshield, please follow the instruction shown right:
SPECIFICATIONS
Pick up Element 1/3” Sony Super HAD Hi-Res. CCD 1/3” Sharp Hi-Res. CCD
Effective Picture Element NTSC: 768(H) x 494(V); PAL: 752(H) x 582(V)
Synchronization Internal
Scanning System 2:1 Interlace
Resolution Horizontal 550 TV Lines Horizontal 540 TV Lines
Sensitivity 0 Lux with IR-LED Built in
S/N Ratio > 48dB (AGC Off)
Gain Control High / Low Selectable
Electronic Shutter NTSC: 1/60 ~ 1/100000s ; PAL: 1/50 ~ 1/110000s
Flickerless On / Off Selectable
Back Light Compensation On / Off Selectable
White Balance Auto White Balance (2000 K ~ 10000K)
Gamma Characteristic 0.45
Video Output 1.0 Vp-p / 75 Ohms. BNC Connector.
Lens Built in DC Dirve Varifocal Lens with Removable IR-Cut Filter
3.7 – 12 mm / F1.6, Wide: 83.9°x61.9°; Tele: 23.91°x17.93°(HxV)
[Optional: f9
–
22 mm / F2.0, Wide: 83.9.°x61.9°; Tele: 23.91°x17.93°(HxV)]
Operating Temperature -10 ~ +50 degree C/ RH85% or Less
Power Consumption 840mAMax (IR On)
250mA Max (IR Off) 780mA Max (IR On) 190mAMax (IR Off)
Luminary 42 units of 850nm IR LED
IR Project Distance 40 Meters – Low / Mid / High Selectable
Power Supply DC 12V ± 10 %
Specifications are subject to change without prior notice.
Support:SecurityManufacturingLtd, Tel:[phone] www.devieweurope.com