DeView CR Series User manual

Side View
Rear View
11
1. Back Focus Adjustment
2. Bracket Mount
3. OSD Control
4. Video Lens Drive Terminal Block
5. D/N Switch
6. Power Input Terminal Block
7. BNC Composite Video Output
8. Power LED Indicator
9. AC Power Input Socket
(AC Mains)
10. Sensor
11. DC Lens Connector
Top View
12
Front View
10
7
8
6
4
5
3
GND
+12V
VIDEO
GND
D/N
VIDEO OUT
7
9
8
100~240VAC~ 50/60Hz
RoHS
D/N
D/N
D/N
Parts Descriptions
Specifications
Connection and Adjustment
Never attempt to disassemble or modify the
camera. Any modification could lead to
damages that are not covered by the
guarantee.
Make sure the power source is switch off and
disconnected before installation. Refer
servicing to qualified personnel only.
To prevent fire or electrical shock, use only
regulated power supply and the wiring should
be used for the appropriate input terminal.
Camera Installation
The camera can be mounted by using either the bracket
mount on the top or bottom (see part descripton 2).
The bracket mounts accept standard photographic mounting
bolts (1/4" BSW or 20 UNC).
AC/DC Low Voltage Power Supply:
The camera operates in either 24 VAC or 12 VDC.
Connections are indicated in the rear panel of the camera.
The power supply must be stable power source and should only be
installed by qualified personnel.
Connect the 75 Ohm coaxial cable to video output (see part description 8).
Precautions
AC Mains Power Supply:
The camera operates directly from the mains supply and is supplied with a
detachable power supply cord. The operating voltage is 100~240 VAC.
Connect the 75 Ohm coaxial cable to video output
(see part description 8).
Connecting to the Power Source and Video Output
Do not expose or operate the camera in wet areas.
Moisture may damage the camera and also increase
the danger of electrical shock.
Do not attempt to aim the camera at the sun or other
extremely bright objects. This may cause damage to
the CCD and the void of warranty.
Do not touch the lens or the CCD by hands while
installing or adjusting the camera. This may cause
damage to the camera.
This product must be installed and maintained in accordance with good
installation practices by qualified personnel only.
To prevent damage to your camera or injury to yourself or to others, read and
comply with the safety precautions as follows:
V531-CR016-200
Ver.03/2011
Ensure the bracket, screws (inc. wall plugs, if
used) and mounting surface can support the
load of the camera and bracket.
Bracket Mount
Protective
Cover
Video Output
Power Input
Terminal
Power Socket
GND
+12V
VIDEO
GND
LAMP
VIDEO OUT
Video Output
Image Picture Element Pixim Seawolf 1/3” Sensor
Effective Picture Element 758(H) x 540(V)
Resolution 690 HTVL-E
Minimum Illumination 50IRE: 0.6 [email protected]
S/N Ratio >50dB
Wide Dynamic Range 120 dB / 17bit
Wide Dynamic Range Area 1 Zone - Fully Adjustable
Electronic Shutter WDR Control (Auto)
Day/Night Auto , D/N switch , Off
White Balance Normal, Extended, Manual
Auto White Balance Range 2800k~9100k(Normal) 2000k~11000k(Ex)
Sync System Internal / Line Lock(AC Only)
Video Output 1.0 Vpp BNC 75Ωunbalanced
Power source AC Mains: 100~240VAC
Low Voltage: 12VDC / 24VAC
Power Consumption Main Power: 3W 20%
Dual Power: 2.88W 20%
Operating Temperature -10°C ~ +60°C
Storage Temperature -30°C ~ +80°C
Dimensions
Weight
65mm (W) x 55mm (H) x 130mm (L)
251.6 g (without lens)
+
-+
-
Digital Slow Shutter up to 32X
Digital Noise Reduction 3D Adaptive
High Resolution Box Camera
CR Series
Instruction Manual

Connection and Adjustment
Lens Installation
Direct Drive (D.C.)Lens Mounting
1. If using a C-mount lens, attach the C-CS mount adaptor before installaing the lens.
2. Move the back focus adjustment lever fully to the left, with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. For Direct Drive Lens application, connect the DC Lens Connector to the side of the camera.
Fit the lens to the camera according to the following connection assignments.
5. Adjust the Back Focus to the correct positon then secure the screw.
6. Adjust the Zoom and Focus levers of the lens to acquire a clear image and
the required field of view.
Video Drive Lens Mounting
1. If using a C-mount lens, attach the C-CS mount adaptor before installaing the lens.
2. Move the back focus adjustment lever fully to the left with the lens facing
towards you (see Back Focus Adjustment).
3. Install the lens on to the camera.
4. For Video Drive Lens application, connect the wires to the rear panel of the
camera. Fit the lens to the camera according to the following connection
assignments.
Strip 6mm of insulation from lens wires. Depress button to open cable clamp
aperture and insert bare end into clamp. Release button to secure wire.
5. Adjust the Back Focus to the correct positon then secure the screw.
6. Adjust the Zoom and Focus levers of the lens to acquire a clear
image and the required field of view
Protective
Cover
Back Focus
Adjustment Lever
Lens
(Not Supplied)
C-CS Mount Adaptor
(for C-type Lens)
Zoom and Focus
Adjustment Levers
Back Focus
Adjustment Lever
Lens
(Not Supplied)
Zoom and Focus
Adjustment Levers
DC Lens
Pin Assignments
Back Focus
Adjustment Lever
Lens
(Not Supplied)
Zoom and Focus
Adjustment Levers
Lens
Connector
Pin Number DC Drive
Pin 1 Damp-
Pin 2 Damp +
Pin 3 Drive +
Pin 4 Drive -
2
1
4
3
Back Focus
Adjustment Lever
Lens
(Not Supplied)
Zoom and Focus
Adjustment Levers
Installing the Lens
Before installing a lens, you must first
remove the protective cover from the
camera. If mounting a C-Mount lens,
attach the C-CS mount adaptor to
the camera.
Adjust the Back Focus to acquire a
sharp image (see Back Focus
Adjustment).
Back Focus Adjustment
There is a mechanism for back focus adjustment.
Loosen the back focus locking screw.
Move the adjustment lever to obtain optimum focus of
the image.
Tighten the screw to lock the back focus
adjustment lever in place. Back Focus Adjustment Lever
Camera Setup
Video Drive Lens
Terminal
GND
+12V
VIDEO
GND
D/N
Button
Press to Open
the Clamp
Cable Clamp
Manual / Fixed Lens Mounting
1. If using a C-mount lens, attach the C-CS mount adaptor before installaing the lens.
2. Move the back focus adjustment lever fully to the left, with the lens facing towards you
(see Back Focus Adjustment).
3. Install the lens on to the camera.
4. Adjust the Back Focus to the correct positon then secure the screw.
5. Adjust the Zoom and Focus levers of the lens to acquire a clear image and the
required field of view.
Camera Configuration
Camera OSD Menu
1. Find the OSD Control on the Rear Panel.
2. With power applied to the camera, press and hold the ENTER key for three seconds
to access the top level menu. A map of the menu options is shown in the following
Camera OSD Menu.
3. Navigate the menus with the Up/Down keys. Sub menus are selectable with Left/Right keys.
4. Remember to SAVE USER SETTINGS prior to exiting the menus to ensure the changes are retained.
5. While navigating the menu, a delay in OSD update is normal.
100~240VAC~ 50/60Hz
D/N
D/N
OSD Control OSD Control
NORMAL
WD NORMAL
OUTDOOR
INDOOR
MANUAL
DC
MODE
WD NORMAL
SAFE AREA
CTR SPOT
LOWER 1/3
DAY/NIGHT CONTROL
VIDEO STANDARD
SYNC
SAVE USER SETTINGS
RESTORE USER SETTINGS
RESTORE FACTORY SETTINGS
RESET CAMERA
SYSTEM INFO
PREVIOUS
KELVIN
R/B
V-PHASE
DG GAIN
AI THRESHOLD
ATW NORMAL
ATW EXTENDED
AWB
MANUAL
AUTO
D/N SWITCH
OFF
PAL
NTSC
LL
INT
INT2
PRESETS
LENS SELECT
WHITE BALANCE
WDR
ADVANCED SETUP
SAVE / RESTORE
EXIT MENU
Camera OSD Menu
ENTER KEY UP
RIGHT
DOWN
LEFT