DeVilbiss FLG-P5-14 User manual

SB-E-2-792ISS.04
Operation Manual
FLG-P5-14
Transtech Pressure-feed Spray Gun
EN

2© 2006 ITW Finishing Systems and Products
Operation Manual
FLG5 – Pressure-Feed Spray Gun
Important
Read and follow all instructions and Safety Precautions before using this
equipment
Description
The FLG5 pressure feed Spraygun is fitted with a 1.4mm Nozzle for use with common coating
materials. A 1.1mm Nozzle and Needle is available as an alternative. The FLG5 Spraygun is
approved to ATEX regulations 94/9/EC, protection level;
II 2 G X. Suitable for use in Zones 1 and 2
Important: These spray guns are suitable for use with solvent-based coating materials. The
design uses EPA compliant atomising (Devilbiss Trans-Tech®) technology to reduce overspray
and improve coating efficiency. Nozzles and needles are manufactured in stainless steel. These
guns are not designed for use with highly corrosive and/or abrasive materials and if used with
such materials it must be expected that the need for cleaning and/or replacement of parts will
be increased. If there is any doubt regarding the suitability of a specific material contact your
local Distributor or ITW Finishing direct.
EC Declaration of Conformity
We, ITW Finishing UK, Ringwood Rd, Bournemouth, Dorset, BH11 9LH, UK, as the
Authorised Representative of the manufacturer of the Spray gun model FLG5, declare, under
our sole responsibility, that the equipment to which this document relates is in conformity with
the following standards or other normative documents:
BS EN 292-1 PARTS 1 & 2: 1991, BS EN 1953: 1999; and thereby conform to the
protection requirements of Council Directive 98/37/EC relating to Machinery Safety Directive,
and;
EN 13463-1:2001, council Directive 94/9/EC relating to Equipment and Protective
Systems intended for use in Potentially Explosive Atmospheres protection level II 2 GX.
This product also complies with the requirements of the EPA guidelines, PG6/34.
Transfer efficiency certificates are available on request.
B. Holt, General Manager
1st January 2006

© 2006 ITW Finishing Systems and Products 3
Specification
Air supply connection - Universal ¼” BSP and NPS
Maximum static air inlet pressure - P1= 12 bar (175 psi)
Nominal gun inlet pressure with gun triggered - 2.4 bar (35 psi)
Maximum service temperature - 40°C
Gun weight - 930 g
Air flow - 277 l/min (9.8 cfm)
Materials of Construction
Gun body - Aluminium .Stainless steel fluid passages
Nozzle - Stainless steel
Needle - Stainless steel
ITW Finishing Systems and Products reserve the right to modify equipment specification without prior notice.
Installation
Important: To ensure that this equipment reaches you in first class condition, protective
coatings have been used. Flush the equipment through with a suitable solvent before use.
1. Attach air hose to
connector (19). Recommended hose size 8 mm bore. The hose must be
conductive and electrical bond from the spraygun to earth should be checked with an
ohmeter. A resistance of less than 106Ohms is recommended.
2 Attach fluid supply hose to Fluid Inlet (28).
Operation
1. Mix coating material to manufacturers instructions
2. Turn needle adjusting screw (18) clockwise to prevent movement.
3. Turn spreader valve (10) counter-clockwise to fully open.
4. Adjust inlet air pressure (For recommended figures see Specifications) at the gun inlet with
the gun triggered.
(pressure gauge attachment shown under Accessories is recommended
for this).
5. Turn needle adjusting screw counter clockwise until first thread shows.
6. Test spray. If the finish is too dry reduce airflow by re
ducing air inlet pressure or by the
Airflow Valve (22). Screw the Adjusting Knob in to reduce pressure.
7.
If finish is too wet reduce fluid flow by turning needle screw (18) clockwise or reducing the
fluid pressure. If atomisation is too coarse, increase inlet air pressure. If too fine reduce inlet
pressure.
8. The pattern size can be reduced by turning adjusting valve (10) clockwise.
9.
Hold gun perpendicular to surface being sprayed. Arcing or tilting may result in uneven
coating.
10.The recommended spray distance is 150-200 mm (6”-8”).
11.Spray edges first. Overlap each stroke a minimum of 50%. Move gun at a constant speed.
12.Always turn off air and fluid supply and relieve pressure when gun is not in use.
SAFETY WARNINGS

4© 2006 ITW Finishing Systems and Products
Fire and explosion
Solvents
and coating materials can be highly flammable or combustible when sprayed.
ALWAYS refer to the coating material suppliers instructions and COSHH sheets
before using this equipment.
Users must comply with all local and national codes of practice and insurance company
requirements governing ventilation, fire precautions, operation and house-
keeping of
working areas.
This equipment, as supplied, is NOT suitable for use with Halogenated
Hydrocarbons.
Static electricity can be generated by fluid and/or air passi
ng through hoses, by the
spraying process and by cleaning non-
conductive parts with cloths. To prevent ignition
sources from static discharges, earth continuity must be maintained to the Spray gun
and other metallic equipment used. It is essential to use c
onductive air and/or fluid
hoses. Personal Protective Equipment
Toxic vapours –
When sprayed, certain materials may be poisonous, create irritation or
be otherwise harmful to health. Always read all labels, safety data sheets and follow any
recommendations for the material before spraying. If in doubt, contact your material
supplier.
The use of respiratory protective equipment is recommended at all times. The type of
equipment must be compatible with the material being sprayed.
Always wear eye protection when spraying or cleaning the Spray gun.
Gloves must be worn when spraying or cleaning the equipment.
Training – Personnel should be given adequate training in the safe use of spraying equipment.
Misuse
Never aim a Spray gun at any part of the body.
Never exceed the max. recommended safe working pressure for the equipment.
The fitting of non-recommended or non-original spares may create hazards.
Before cleaning or maintenance, all pressure must be isolated and relieved from the equipment.
The product should be cleaned using a gun-washing
machine. However, this equipment should
not be left inside gun-washing machines for prolonged periods of time.
Noise Levels
The A-weighted sound level of Spray guns may exceed 85 dB (A) depending on the set-
up being used.
Details of actual noise levels are available on request. It is
recommended that ear protection is worn at all times when spraying.
Operating
Spray e
quipment using high pressures may be subject to recoil forces. Under certain
circumstances, such forces could result in repetitive strain injury to the operator.

© 2006 ITW Finishing Systems and Products 5
Parts List
Ref. No
Part Number Description
1
SGK-0023
Retaining ring
1
2 FLG-0001-622 Air cap No 622 1
3
SGK-0012-14
Fluid tip 1.4mm
1
«● 4 - Gasket 1
● 5K-5032 Sprayhead Kit 1
«
6
-
Packing
1
7 - Packing gland nut 1
8 - Circlip 1
9 - Spray pattern adjustment valve bushing 1
10
-
Spray pattern valve
1
«
11
-
U-cup seal
2
«
12
-
Air-valve seat
1
«
13
-
Air-valve stem
1
« 14 - Air-valve spring 1
15
-
Air-valve bushing
1
16 SGK-0402-14 Fluid needle1.4mm 1
17
-
Fluid needle spring
1
18 - Fluid adjustment knob 1
19 - Nipple 1
20 - Circlip 1
21
-
Air adjusting valve head
1
22
-
Air adjusting valve assembly
1
23
-
Circlip
1
24
-
Trigger pin assembly
1
25 - Trigger 1
26 - Nut 1
27 - Washer 1
28
-
Nipple assembly fluid
1
«
●29
-
Gasket
1
« 30 - Assembly Tool 1
«K-5044 Seal, baffle and gasket replacement kit, items 4, 6, 11, 12, 13, 14, 29 and 30
●K-5032: Baffle replacement kit, items 4 ,5 and 29
+ SGK-13-11 Fluid tip 1.1mm
∞SGK-402-11 Fluid needle 1.1mm

6© 2006 ITW Finishing Systems and Products
Preventative Maintenance
1. Turn off air and coating supply and relieve pressure in the supply lines, or if using QD
system, disconnect from airline and fluid line.
2. Remove air cap (1) & (2) and clean. If any of the holes
in the cap are blocked with coating
material use a toothpick to clean. Never use metal wire which could damage the cap and
produce distorted spray patterns
3.
Ensure the tip of the nozzle (3) is clean and free from damage. Build up of dried paint can
distort the spray pattern.
4. Lubrication – stud (24), needle (16) and air valve (13) should be oiled each day.

© 2006 ITW Finishing Systems and Products 7
Replacement of Parts
Nozzle (3) and needle (16) – Remove parts in the following order: 18, 17, 16, 1, 2 and 3. Check
condition of nozzle seal (4)
and replace if necessary. Replace any worn or damaged parts and
re-assemble in reverse order. Recommended tightening torque for nozzle (3) 16-20 Nm (150-
180 lbf in).
Packing – Remove parts 18, 17, 16. Unscrew packing n
ut (7). Remove packing (6). Fit new
packing (6) and nut (7). Re-assemble parts 16, 17, and 18 and tighten packing n
ut (7) with
spanner sufficient to seal but to allow free movement of needle. Lubricate with gun oil.
Air-valve Seal Kit K-5040
1. Remove adjusting knob (18), spring (17), and needle (16).
2. Loosen housing (15).
3. Remove housing (15) and air-valve spring (14).
4. Remove spindle (13).
5. Using service tool (40), engage groove behind the valve seat (12) and remove valve seat.
6. Push out the front air-valve seal (11).
7. Turn the gun upside down and let the seal fall out.
8. Fit new front seal (11) to service tool.
9. Fit new seal to gun body and press firmly to ensure seal is engaged.
10.Fit new valve seat (12) to service tool and fit valve seat into gun body.
11.Remove rear air-valve seal (11) from housing (15) with a hooked instrument.
12.Fit new seal to service tool and fit seal to housing (15).
13.Replace spindle (13).
14.Replace valve spring (14), screw in housing (15) and tighten.
15.Screw reverse end of service tool into housing until fully engaged. Tighten by hand to seat
the valve seat. Remove tool.
16.Fit needle (16), spring (17) and knob (18).
17.Adjust needle packing (7) with s
panner sufficient to seal but to allow free movement of
needle. Lubricate with gun oil.
Spreader valve (10) – Caution: always ensure that the v
alve is in the fully open position by
turning screw fully counter-clockwise before fitting to body.
Air cap / Nozzle selection
Refer to coating material manufacturers recommendations or ITW Finishing UK Website:
www.itweuropeanfinishing.com
Accessories
Cleaning brush – order 4900-5-1-K3
Air-adjusting valve and gauge – order HAV-501-B
Digital pressure gauge – DGI-501-BAR
Lubricant – order GL-1-K10
Spray gun cleaning kit – KK-4584

8© 2006 ITW Finishing Systems and Products
ITW Finishing Systems and Products
Ringwood Road,
Bournemouth,
BH11 9LH,
England.
Tel. No. [phone]
Telefax No. [phone],
Website address
http://www.itweuropeanfinishing.com
ITW Finishing Systems and Products is a Division of ITW Ltd. Reg. Office:
Admiral House,
St Leonard’s Road,
Windsor,
Berkshire,
SL4 3BL,
UK
Registered in England: No 559693 Vat No 619 5461 24