DeVilbiss JGA User manual

1 ©ITW Ltd 2001
Operation Manual
JGA – Suction Feed Spraygun
E
EP 2 - 8
SB-E-2-252-I

2©ITW Ltd 2001
Operation Manual
JGA – Suction Feed Spraygun
Important
Read and follow all instructions and Safety Precautions before using this
equipment
Description
The JGA Suction Feed Spraygun Kit is suitable for use with most solvent
based coating materials. Nozzles and Needles are available in Stainless
Steel.
Important: These guns are not designed for use with highly corrosive and/
or abrasive materials and if used with such materials it must be expected
that the need for cleaning and/or replacement of parts will be increased. If
there is any doubt regarding the suitability of a specific material contact
your local Distributor or ITW Finishing direct.
Declaration of Conformity
We, ITW Finishing UK, Ringwood Road Bournemouth Dorset
England declare under our sole responsibility that this product is in
conformity with BS EN 292: parts 1 and 2 :1991 and BS EN
1953:1999, following the provisions of the Machinery Directive
89/392/EEC.
B.Holt,General Manager
E
E
Model Part Number
Example: JGA-614FWH-186B
Fluid Tip Size
Aircap No
Kit Number
Nozzle Material
H = 303 Stainless

3 ©ITW Ltd 2001
SAFETY WARNINGS
Fire and explosion
Solvents and coating materials
can be highly flammable or
combustible when sprayed. ALWAYS
refer to the coating material suppliers
instructions and COSHH sheets
before using this equipment
Users must comply with all local
and national codes of practice and
insurance company requirements
governing ventilation, fire precautions,
operation and house-keeping of working
areas
This equipment, as supplied, is
NOT suitable for use with
Halogenated Hydrocarbons.
Static Electricity can be generated by
fluid and/or air passing though hoses. To
prevent such a risk, earth continuity to
the spray equipment and the object
being sprayed should be maintained.
Personal Protective
Equipment
Toxic vapours – When sprayed,
certain materials may be
poisonous, create irritation or be
otherwise harmful to health.
Always read all labels and safety data
sheets for the material before spraying
and follow any recommendations. If In
Doubt, Contact Your Material Supplier
The use of respiratory protective
equipment is recommended at all
times. The type of equipment
must be compatible with the material
being sprayed
Always wear eye protection when
spraying or cleaning the spraygun
Gloves must be worn when
spraying or cleaning the
equipment
Training – Personnel should be given
adequate training in the safe use of
spraying equipment.
Misuse
Never aim a spraygun at any part of the
body
Never exceed the max. recommended
safe working pressure for the equipment
The fitting of non-recommended or non-
original spares may create hazards
Before cleaning or maintenance, all
pressure must be isolated and relieved
from the equipment
The product should be cleaned using a
gun washing machine. However, this
equipment should not be left inside gun
washing machines for prolonged periods
of time.
Noise Levels
The A-weighted sound level of
sprayguns may exceed 85 dB
(A) depending on the set-up
being used. Details of actual
noise levels are available on request. It is
recommended that ear protection is worn
at all times when spraying
E
E

4©ITW Ltd 2001
Parts List
Ref. No Description Part Number Qty
1 Air Cap/Retaining ring See Chart 1 1
1a Spring Clip - Kit of 5 JGA-156-K5 1
+*2 Nozzle AV-645-** 1
3 Baffle & Seal JGD-402-K 1
Baffle seal - Kit of 5 GTI-33-K5 1
+4 Packing GTI-439-K2 1
5 Spreader Valve GTI-405-K 1
6 Stud and Screw GTI-408-K5 1
+7 Needle See Chart 2 1
+8 Spring - Kit of 5 GTI-409-K5 1
9 Bushing JGA-17 1
10 Needle Adjusting Screw GTI-414-K 1
11 Valve Assembly JGK-449 1
12 Trigger JGS-108-1 1
13 Connector JGA-158 1
14 Airflow Valve GTI-415-K 1
15 Lock Nut - Kit of 5 JGA-51-K5 1
16 Seal 23165-001 1
17 Fluid Inlet Connector and seal JGA-159-K 1
18 Fluid Tube KR-456-B 1
19 Yoke KR-77-1 1
20 Washer - kit of 5 KS-48-K5 2
21 Cam KR-130 1
22 Washer - Kit of 5 KR-40-K5 1
23 Lid Gasket - kit of 3 KR-11-K3 1
24 Nut - kit of 5 KR-94-K5 1
25 Drip free diaphragm—kit of 5 KR-115-K5 1
26 Cup KR-466-K 1
27 Cup lid assembly KR-4001-B 1
28 Cup and Lid assembly Kit KR-566-1-B 1
29 Seal + Pin Kit ( + SST-8434-K5) GTI-428-K5 2
30 Circlip - Kit of 5 SST-8434-K5 2
31 Circlip - Kit of 5 25746-007-K5 1
+32 Seal - Kit of 5 JGS-72-K5 2
+3a
33 Spanner SPN-5 1
34 Air valve stem assembly JGS-431-1 1
35 Spring JGV-262-K5 1
* - ** Denotes Nozzle Size - see chart 1 below for available sizes
+ - Parts included in service Kit KK-4502 (see accessories)
E
E

5 ©ITW Ltd 2001
Specification
Air supply connection - Universal 1/4 BSP and NPS
Fluid Supply Connection - Universal 3/8 BSP and NPS
Maximum static inlet pressure - P1= 9 bar (130 psi)
Maximum static fluid pressure - P1= 14 bar (203 psi)
Gun Weight - 695 g
Cup Weight - 460g
Materials of Construction
Gun body - Polished Aluminium
Nozzle - Stainless Steel
Needle - Stainless Steel
Cup - Aluminium with Brass Nickel plated pins
Lid Assembly - Aluminium, Brass and Steel Nickel plated
Cup Lid Gasket - Polyethylene
Diaphragm - Polyethylene
E
E
Chart 1. Aircap and Nozzle Size combinations
Aircap
No
Aircap Part
Number
FW
1.6
FF
1.4
EX
1.8
30 AV-4239-30 X X X
43 AV-4239-43 X X X
80 MB-4039-80 X X X
186 AV-4239-186 X X X
Nozzle
Size
Needle Order
Number
FW JGA-421-FF
FF JGA-421-FF
EX JGA-421-EX
Chart 2. Nozzle and Needle Combinations
Nozzle Order
Number
AV-645 FW
AV-645-FF
AV-645-EX

6©ITW Ltd 2001
Installation
Important: To ensure that this
equipment reaches you in first class
condition, protective coatings have
been used. Flush the equipment
through with a suitable solvent
before use.
1. Attach air hose to connector (13).
Recommended hose size 8 mm
bore. The air supply should be
filtered and regulated.
2. Attach the Cup Lid assembly (27)
to the Fluid Inlet connector (17).
3. Position the Yoke at right angles
to the Gun with the Cam lever to
the front (see picture). Make sure
the vent hole in the lid is
positioned under the Yoke and
the hole in the diaphragm is 180°
to the Lid vent hole.
E
E
Operation
1. Mix coating material to
manufacturers instructions.
2. Fill the cup with the required
amount of material. Fill to no more
than 25mm(1“) from the top of the
cup. DO NOT OVERFILL.
3. Attach Cup to the Lid assembly.
4. Turn needle adjusting screw (10)
on the spraygun clockwise to
prevent movement.
5. Turn pattern valve (5) counter-
clockwise to fully open
6. Adjust inlet air pressure to give
3.5 bar (50psi) at the gun inlet
with the gun triggered. (pressure
gauge attachment shown under
Accessories is recommended for
this).
7. Turn needle adjusting screw
counter clockwise until first thread
shows.
8. Test spray. If the finish is too dry
reduce airflow by reducing inlet
pressure. If finish is too wet
reduce fluid flow by turning needle
screw (10) clockwise. If
atomisation is too coarse,
increase inlet air pressure. If too
fine reduce inlet pressure.
9. The pattern size can be reduced
by turning adjusting valve (5)
clockwise.
10.Hold gun perpendicular to surface
being sprayed. Arcing or tilting
may result in uneven coating.
11.The recommended spray distance
is 150-200 mm (6”-8”).
12.Spray edges first. Overlap each
stroke a minimum of 50%. Move
gun at a constant speed.
13.Always turn off air supply and
relieve pressure when gun is not
in use.
Air Flow Valve (14)
1. If the airflow valve (14) is fitted
this can be used to reduce the
inlet pressure through the gun.
Screw the Adjusting Knob in to
reduce pressure.

7 ©ITW Ltd 2001
1. Turn off air and relieve pressure
in the supply lines, or if using QD
system, disconnect from airline.
2. Release Cup and raise the tube
out of the material. Trigger the
Gun and allow material to drain
back into the cup.
3. Dispose of the surplus material
and clean the cup.
4. Remove air cap (1) and clean. If
any of the holes in the cap are
blocked with coating material use
a toothpick to clean. Never use
metal wire which could damage
the cap and produce distorted
spray patterns
5. Ensure the tip of the nozzle (2) is
clean and free from damage.
Build up of dried paint can distort
the spray pattern.
6. Lubrication – stud/screw (6),
needle (7) and air valve (11)
should be oiled each day.
Preventative Maintenance
Replacement of Parts
Nozzle (2) and Needle (7) –
Remove parts in the following order:
10, 8, 7, 1 and 2. Replace any worn
or damaged parts and re-assemble
in reverse order. Recommended
tightening torque for nozzle (2) 17-
20 Nm (150-180 lbf in)
Packing – Remove parts 10, 8, 7.
Unscrew cartridge (4). Fit new
cartridge finger tight. Re-assemble
parts 7, 8, and 10 and tighten
cartridge (4) with spanner sufficient
to seal but to allow free movement
of needle. Lubricate with gun oil.
Air valve (11) – Remove Trigger,
parts 6 and 12. Unscrew valve
assembly. Re-assemble, fitting
spring to valve head before fitting
valve.
Spreader valve (5) – Caution:
always ensure that the valve is in
the fully open position by turning
screw fully counter-clockwise before
fitting to body.
Accessories
Cleaning Brush – order 4900-5-1-K3
Service Kit – order KK-4502 add nozzle size as required-
(i.e. KK-4502-FF-H)
Seal Kit - order KK-4558. Contains 3a, 4, 29, 30, 32
Pressure gauge Attachment – order GA-515
Gun Mounted Regulator – order DVR-501
Lubricant - order GL-1-K10
E
E

8©ITW Ltd 2001
January 03
ITW Finishing Systems and Products
Ringwood Road,
Bournemouth,
BH11 9LH,
England.
Tel. No. [phone]
Telefax No. [phone],
Website address http://www.itweuropeanfinishing.com
ITW Oberflächentechnik GmbH & Co. KG
Justus-von-Liebig-Straße 31
63128 Dietzenbach
Tel [phone]
Telefax: (060 74) 403300
Website address http://www.itw-finishing.de
ITW Surfaces Et Finitions
163-171 avenue des Auréats B.P. 1453
26014 VALENCE CEDEX FRANCE
Tél. [phone]
Télex 345 719F DVILBIS
Téléfax: (33) 475-75-27-99