DeWalt DW0165 User manual

Please read these instructions before operating the product.
www.DEWALT.co.kr
E
PT
KR
E
F
TR
DW0165, DW0165S, DW0330S
User Manual
사용 설명서
DEWALT Laser Safety, Maintenance, and Warranty
DEWALT 레이저 안전, 유지 보수 및 보증
제품을 작동하기 전에 본 설명서를 읽으십시오.
DW0165SDW0165 DW0330S

User Manual 3
사용 설명서 25
Laser Safety, Maintenance, and Warranty39
레이저 안전 , 유지 보수 및보증 45

1
2
0.000 m
0.000 m
0.000 m
0.000 m
50.0°
DW0165S
B
D
AAA
AAA
AAA
AAA
AAA
3
Figures/그림
A
4
DW0165
4.5V DC
2
5
6
1
3
78
C
31
2
4
5
6
0.0000 m
0.0000 m
0.0000 m
0.0000 m
50.0°

4
a
a
50.0°
F
DW0165S
DW0330S
1
2
3
0.0000 m
0.0000 m
0.0000 m
0.0000 m
50.0°
4
=
=
=
=
1
3
4
G
ft/m
E
2

5
Figures/그림
H
J
K
0.0000 m
0.0000 m
0.0000 m
0.7000m
50.0°
I
71.77 in
45.86 in
45.86 in
50.0°
max
min
+
0.3000 m
0.7000 m
1.0000m
50.0°
+-
/
0.8500m
-
50.0°
0.1500 m
1.0000 m
+
-
/

6
L
0.6000 m
0.4000 m
0.2400 m
50.0°
2
M
N
O
0.7000 m
0.6000 m
0.5000 m
0.2100 m
50.0°
3
2
0.240 m
2
+
0.210 m
0.450 m2
50.0°
+-
/
+/-
+/-

7
Figures/그림
1.0100m
2.7390 m
50.0°
2.1000 m
?
P
Q
?
R

8
4.8270m
24.3°
0.0320 m
24.3°
?
S
T

9
Figures/그림
12”
12”
12”
0.000 in
0.00 in
12.0 in
50.0°
a
a
12”
12”
0.000 in
12.0 in
12.0 in
50.0°
a
a
12” 12”
0.000 in
12.0 in
12.0 in
50.0°
a
a
12”
U

10
180°
90°
180°
X
15.0°
15.0°
50.0°
V
?
W

11
E
Contents
• User Safety
• Battery Safety
• Loading Batteries
• Turning the Tool On
• Choosing the Settings
• Taking Measurements
• Calibrating the Tool
• Warranty
• Specications
• Error Codes
Retain all sections of this manual for future
reference.
User Safety
WARNING:
Carefully read the Safety Instructions and
Product Manual before using this product.
The person responsible for the product must
ensure that all users understand and adhere
to these instructions.
WARNING:
The following label information is placed on
your laser tool to inform you of the laser class
for your convenience and safety.
DW0165
4.5V DC
DW0165S
FCC ID: 2ANWF-DW0165
IC: 23237-DW0165
4.5V DC
The DW0165/DW0165S/DW0330S tool emits a visible
laser beam, as shown in Figure A1. The laser
beam emitted is Laser Class 2 per IEC 60825-1 and
complies with 21 CFR 1040.10 and 1040.11 except
for deviations pursuant to Laser Notice No. 50, dated
June 24, 2007.
WARNING:
While the laser tool is in operation, be careful
not to expose your eyes to the emitting laser
beam (red light source). Exposure to a laser
beam for an extended time period may be
hazardous to your eyes. Do not look into the
beam with optical aids.
WARNING: To reduce the risk of injury,
user must read the Product User manual,
Laser Safety manual, and Battery Safety
information.
FCC Compliance
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
FCC Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. This device is
a portable unit. The exclusion threshold is 0.887<3.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
the receiver.
- Connect the equipment into an outlet on a different
circuit (not the circuit to which the receiver is
connected).
DW0330S
FCC ID: 2ANWFDW0330
IC: 23237-DW0330
4.5V DC

12
E- Consult the dealer or an experienced radio/TV
technician for help.
Canada, Industry Canada (IC) Notices
Class B digital circuitry of this device complies with
Canadian ICES-003. This device complies with
Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of
the device.
Under Industry Canada regulations, the radio
transmitter(s) in this device may only operate using
an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful
communication.
Battery Safety
WARNING: Batteries can explode or leak
and cause serious injury or re. To reduce the
risk:
ALWAYS follow all instructions and warnings
on the battery label and package.
DO NOT short any battery terminals.
DO NOT charge alkaline batteries.
DO NOT mix old and new batteries. Replace
all of them at the same time with new
batteries of the same brand and type.
DO NOT mix battery chemistries.
DO NOT dispose of batteries in re.
ALWAYS keep batteries out of reach of
children.
ALWAYS remove batteries if the device will
not be used for several months.
NOTE: Ensure that the recommended
batteries are used.
NOTE: Ensure the batteries are inserted in
the correct manner, with the correct polarity.
Loading Batteries
1. Pull up the endpiece on the back of the tool
(Figure D1).
2. Pull up the battery compartment latch on the back
of the tool (Figure D2and D3).
3. Insert three AAA batteries, making sure to position
the -and +ends of each battery as noted inside
the battery compartment (Figure D4).
4. Push the battery door down until it snaps in place
(Figure D5).
When the tool is ON, the battery level appears on the
screen (Figure C1).
Turning the Tool On
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
Choosing the Settings
Setting Automatic Turn Off
By default, the tool will automatically turn off
90 seconds after no buttons or options have been
selected. To change when the tool automatically turns
off, follow these steps.
1. On the first screen (Figure E1), press to
display the Main Menu.
2. On the Main Menu (Figure E2), select and
press .
3. On the Settings Menu (Figure G), select and
press .
4. Select the time.
• Choose to turn off the tool after 30 sec, 60 secs,
90 secs, or 300 secs.
• To keep the tool turned on until you manually
turn it off (by pressing and holding for
10 seconds), select
∞
.
5. Press to save your setting.

13
E
Setting Screen Brightness
By default, the tool's screen will be set at 25%
brightness. To change the brightness level, follow
these steps.
1. On the first screen (Figure E1), press to
display the Main Menu.
2. On the Main Menu (Figure E2), select and
press .
3. On the Settings Menu (Figure G), select and
press .
4. Select the desired brightness level: 25%, 50%,
75%, or 100%.
5. Press to save your new setting.
Turning Off the Sound
By default, the tool will beep each time you take a
measurement. You can turn off the beeps.
1. On the first screen (Figure E1), press to
display the Main Menu.
2. On the Main Menu (Figure E2), select and
press .
3. On the Settings Menu (Figure G), select and
press to display .
4. Press to save your setting.
Changing the Unit of Measure
ft/m
By default, the tool will display measurements in
inches (74 9/16 in). You can change the unit of
measure to fractional ft (6'02"9/16), meters (1.8940 m),
decimal ft (6.21 ft), or decimal inches (3.21 in).
1. On the first screen (Figure E1), press to
display the Main Menu.
2. On the Main Menu (Figure E2), select and
press .
3. On the Settings Menu (Figure G), select ft/m
and press .
4. Select the unit of measure.
• 0'00" 0/00
• 0" 0/00
• 0'00" ft
• 0.00 in
• 0.0000 m
5. Press to save your setting.
Choosing the Tool Position
By default, distances are measured from the bottom
of the tool to a wall or object (Figure F3). To
measure distances from a different tool location, follow
these steps.
1. On the first screen (Figure E1), press to
display the Main Menu.
2. On the Main Menu (Figure E2), select and
press .
3. Select the tool position.
• To measure from the top of the tool
(Figure F1), select .
• To measure from the tripod connection on the
tool (Figure F2), select .
• To measure from a corner or another hard-to-
reach location with the endpiece flipped open
(Figure D1), select (Figure F4) to
measure from the end of the endpiece.
4. Press to save your new setting.
Taking Measurements
Measuring Distance
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Point the tool's laser (Figure A1) toward
the wall or object whose distance you need to
measure (Figure H1).

14
E5. Press to measure the distance from the
tool to the wall or object.
6. At the bottom of the screen, view the current
measurement (Figure H2).
To take a new measurement, press to move
the current measurement up to the previous line on
the screen. Then repeat steps 4-6.
Adding 2 Measurements
You can add two measurements to get a total
measurement of the two distances (Figure I).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2)
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Press to indicate that you want to add two
measurements.
6. Point the tool's laser toward the wall or object
whose distance you need to measure
(Figure I1).
7. Press to measure the distance from the
tool to the first wall or object.
8. Point the tool's laser toward the next wall or object
(Figure I2).
9. Press to measure the distance and add it
to the previous measurement.
10. View the total of the two measurements at the
bottom of the screen (Figure I3).
Subtracting 2 Measurements
You can subtract one measurement from another
(Figure J).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Press to indicate that you want to subtract
one measurement from another.
6. Point the tool's laser toward the wall or object
whose distance you need to measure
(Figure J1).
7. Press to measure the distance from the
tool to the wall or object.
8. Point the tool's laser toward the wall or object
whose distance is to be subtracted from the first
measurement (Figure J2).
9. Press to measure the distance and
subtract it from the previous measurement.
10. View the difference between the two
measurements at the bottom of the screen
(Figure J3).

15
E
Measuring Continuously
To take a series of measurements as you move
around, change to Continuous Measure mode
(Figure K).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Point the tool's laser (Figure A1) toward
the wall or object whose distance you need to
measure (Figure K1).
6. At the bottom of the screen, view the current
measurement (Figure K2), which will keep
changing as you move the tool.
7. To take the current measurement (from the tool to
the wall or object) and exit Continuous Measure
mode, press .
To take a new measurement, press to move
the current measurement up to the previous line on
the screen. Then repeat steps 4-7.
Measuring Area
You can measure the area of a wall, floor, or object
(Figure L).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Measure the width (Figure L1).
• Point the top of the tool at one side of the wall,
floor, or object.
• Position the tool at one end of the wall, floor,
or object and point the laser dot across the
width. (Figure L1shows where to position
the tool if you are measuring from the bottom
of the tool.)
• Press to display the width measurement
at the top of the screen.
6. Measure the length (Figure L2).
• Position the tool at one end of the wall, floor,
or object and point the laser dot across the
length. (Figure L2shows where to position
the tool if you are measuring from the bottom
of the tool.)
• Press to display the length measurement
on the second line of the screen.
7. View the Area measurement at the bottom of the
screen (Figure L3).
Adding/Subtracting 2 Areas
You can measure the area of a wall, floor, or object
and then add it to, or subtract it from, the area of
another wall, floor, or object (Figure M).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.

16
E4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Press to add, or to subtract, the areas of
two walls, floors, or objects.
6. Measure the width of the first wall, floor, or object
(Figure M1).
• Position the tool at one end of the wall, floor,
or object and point the laser dot across the
width. (Figure M1shows where to position
the tool if you are measuring from the bottom
of the tool.)
• Press to display the width measurement
at the top of the screen.
7. Measure the length of the first wall, floor, or
object (Figure M2).
• Position the tool at one end of the wall, floor,
or object and point the laser dot across the
length. (Figure M2shows where to position
the tool if you are measuring from the bottom
of the tool.)
• Press to display the length measurement
on the second line of the screen.
8. Follow the same steps to measure the width and
length of the second wall, floor, or object.
9. View the Area measurement at the bottom of the
screen (Figure M3).
Measuring Volume
You can measure the volume of a room or object
(Figure N).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Measure the width (Figure N1).
• Point the top of the tool at one side of the target
(room or object).
• Position the tool at one end of the target and
point the laser dot across the width.
(Figure N1shows where to position the
tool if you are measuring from the bottom of
the tool.)
• Press to display the width measurement
at the top of the screen.
6. Measure the length (Figure N2).
• Position the tool at one end of the target and
point the laser dot across the length.
(Figure N2shows where to position the
tool if you are measuring from the bottom of
the tool.)
• Press to display the length measurement
on the second line of the screen.
7Measure the height (Figure N3).
• Position the tool at one end of the target and
point the laser dot across the height. (Figure
N3shows where to position the tool if you
are measuring from the bottom of the tool).
• Press to display the height measurement
on the third line of the screen.
8. View the Volume measurement at the bottom of
the screen (Figure N4).

17
E
Adding/Subtracting 2 Volumes
You can measure the volume of room or object
and then add it to, or subtract it from, the volume of
another room or object (Figure O).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Press to add, or to subtract, the volumes
of two rooms or objects.
6. Measure the width (Figure O1).
• Position the tool at one end of the room or
object and point the laser dot across the width.
(Figure O1shows where to position the
tool if you are measuring from the bottom of
the tool.)
• Press to display the width measurement
at the top of the screen.
7. Measure the length (Figure O2).
• Position the tool at one end of the room or
object and point the laser dot across the length.
(Figure O2shows where to position the
tool if you are measuring from the bottom of
the tool.)
• Press to display the length measurement
on the second line of the screen.
8. Measure the height (Figure O3).
• Position the tool at one end of the room or
object and point the laser dot across the height.
(Figure O3shows where to position the
tool if you are measuring from the bottom of
the tool).
• Press to display the height measurement
on the third line of the screen.
9. Follow the same steps to measure the width,
length, and height of the second room or object.
10. View the Volume measurement at the bottom of
the screen (Figure O4).
Measuring the Height of a Tall Object
If you need to measure the height of a tall object
(e.g., a tall building), you can calculate the height
based on the distance to 1 point or the distances
from the same point to 2 points on the object. The
tool will use the Pythagorean Theorem (C2=A2+B2) to
calculate the height.
Distance to 1 Point
You can use the distance to one point on a wall
or object (Indirect Height) to determine its height
(Figure P).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Position the tool opposite the bottom of the
vertical height to be measured (Figure P1).

18
E6. Point the laser toward the highest point of the
building or object whose height you need to
measure (Figure P1).
7. Press to measure the distance.
8. View the height measurement at the bottom of the
screen (Figure P2).
Distances to 2 Points
You can use the distance to two points on a wall
or object (Double Indirect Height) to determine its
height (Figure Q).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Position the tool opposite the approximate
center of the vertical height to be measured
(Figure Q1).
6. Point the laser toward the lowest point of the
building or object whose height you need to
measure (Figure Q2).
7. Press to measure the distance.
8. From the same point, aim the laser at the
highest point of the building or object
(Figure Q3).
9. Press to measure the distance.
10. On the bottom line of the screen, view the height
of the building or object (Figure Q4).
Measuring Partial Height of a Wall
If you need to determine the height of a section of a
wall or object (e.g., the distance from the ceiling to
the top of TV or window on the wall) (Figure R).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Point the laser at the highest point of the wall or
object (Figure R1).
6. Press to measure the distance to the top
of the tall object.
7. From the same point, aim the laser at the top
of the obstruction on the wall or object
(Figure R2).
8. Press to measure the distance from the
top of the wall to the obstruction (TV, window,
etc.).
9. From the same point, aim the laser on a
horizontal line straight ahead toward the bottom
of the wall (Figure R3).
10. Press to measure the distance.
11. On the bottom line of the screen, view the
distance between the top of the wall and the top
of the obstruction on the wall (Figure R4).

19
E
Measuring Height of Obstructed Object -
Follow these steps to determine the height of a tall
building or object that is blocked by other buildings
or objects (Figure S).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select
(Figure E4).
• Press .
5. Point the laser at the highest point of the
building, wall, or object (Figure S1).
6. Press to take the measurement.
7. On the bottom line of the screen, view the height
of the building or object (Figure S2).
Measuring from a Tripod
If you are placing the tool on a tripod to measure
the height of a tall building, follow these steps
(Figure T).
1. Screw the 1/4-20" hole on the back of the tool
onto the 1/4-20" connection on the top of your
tripod (Figure T1).
2. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
3. Press (Figure A3) to turn the tool on
and display the red laser dot.
4. Make sure the tool position setting (Figure C4)
is to measure from the tripod connection.
5. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select
(Figure E4).
• Press .
6. Point the laser at the lowest point of the wall or
object whose height you need to measure
(Figure T2).
7. Press to take the measurement.
8. Point the laser at other points on the wall or object
(Figure T3).
9. When ready, press to take the
measurement.
10. On the bottom line of the screen, view the height
of the wall or object (Figure T4).
Positioning Studs a
a
When you are framing a wall, use the Stakeout
feature to easily mark the position of each stud
(Figure U).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is set to to measure from the back of the tool.
4. Select
a
aas the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select
a
a
(Figure E4).
• Press .

20
E5. Determine the distance between each stud, for
example, 12".
6. Press and until the top number on the
screen is set to the distance from the right edge
of one stud to the left edge of the next (e.g., 12")
(Figure U1).
7. Line up the back of the tool with the right edge of
the last stud that is nailed in (Figure U2).
8. Press to start measuring the distance as
you slowly move the tool to the right.
9. Continue moving the tool to the right until
the bottom number on the screen is 0.00 in
(Figure U3).
10. Press to stop measuring.
11. Using a pencil, mark the location where the left
edge of the stud should be nailed into the wall
frame.
12. Nail the left edge of the stud at the marked
location.
13. For each remaining stud in the wall frame, repeat
steps 7-12 (Figure U4).
Measuring an Angle
If you need to determine the angle at which
something is positioned, use the tool to measure
that angle (Figure W).
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Make sure the tool position setting (Figure C4)
is correct for taking the measurement.
4. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
5. Position the tool at the angle to be measured
(Figure W1).
6. Press to take the measurement.
7. View the angle measurement on the screen
(Figure W2).
Using the Tool as a Level
1. Point the tool's laser (Figure A1) toward a wall
or object, and not toward anyone's eyes.
2. Press (Figure A3) to turn the tool on
and display the red laser dot.
3. Select as the measurement type.
• Press to display the Main Menu
(Figure E2).
• Press to select .
• Press to display the Measurement Type
Menu (Figure E3).
• Press the arrow buttons to select .
• Press .
4. Place the tool in the vertical or horizontal position
on the surface that you want to check is level
(Figure V1).
5. On the tool's screen, view the position of the white
bubble on the vial (Figure V2).