DFI EC510 User manual

www.d.com
1
Chapter 1 Introduction
EC510/511-KH
User’s Manual
A55900933
Preliminary
Version

www.d.com
2
Chapter 1 Introduction
Copyright
This publication contains information that is protected by copyright. No part of it may be re-
produced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2019. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.

www.d.com
3
Chapter 1 Introduction
Table of Contents
Copyright.............................................................2
FCC and DOC Statement on Class A ..................... 2
About this Manual................................................4
Warranty ............................................................4
Static Electricity Precautions .................................4
Safety Measures...................................................4
Safety Precautions ...............................................5
About the Package............................................... 5
Chapter 1 - Introduction....................................... 6
Overview.................................................................................6
Key Features ...........................................................................6
Specifications...........................................................................7
Getting to Know the EC510/EC511-KH ......................................8
Mechanical Dimensions ............................................................9
Chapter 2 - Getting Started ..................................10
Chapter 3 - Installing the Devices......................... 11
Removing the Chassis Cover................................................... 11
Installing a SODIMM ..............................................................12
Installing a 2.5” SATA Drive.................................................... 13
Installing a Mini PCIe Card ..................................................... 14
Installing an M.2 Card............................................................15
Installing a PCI or PCIe Expansion Card.................................. 16
Installing a CPU.....................................................................17
Chapter 4 - Jumper Settings.................................19
Clear CMOS Data ................................................................... 19
PS/2 KB/MS Power Select.......................................................19
COM1/COM2 RS232 Power Select ........................................... 20
DIO Power Source Select (Pins 0~7) ...................................... 20
COM1/COM2 RS232/422/485 Select....................................... 21
COM3/COM4 RS232/422/485 Select........................................ 22
DIO High/Low Select (DIO 0~3)............................................. 23
DIO High/Low Select (DIO 4~7)............................................. 23
Chapter 5 - Ports and Connectors......................... 24
Front Panel I/O Ports .............................................................24
USB Ports................................................................................................... 24
COM (Serial) Ports ...................................................................................... 25
Rear Panel I/O Ports .............................................................. 25
RJ45 LAN Ports........................................................................................... 26
Display Interfaces ....................................................................................... 26
USB Ports................................................................................................... 27
9~36V DC-in .............................................................................................. 27
I/O Connectors ...................................................................... 28
PS/2 KB/MS Connector................................................................................ 28
SATA (Serial ATA) Connectors...................................................................... 28
SATA (Serial ATA) Power Connectors............................................................ 29
SMBus Connector ...................................................................................... 29
Rear Audio Connector ................................................................................. 30
Digital I/O Connector & DIO Power ............................................................. 30
12V DC-out ................................................................................................ 31
Front Panel Connector ............................................................................... 31
Expansion Slots .......................................................................................... 32
LPC Connector............................................................................................ 33
LAN Ports (daughter board) ....................................................................... 34
Digital I/O Connector (daughter board) ....................................................... 34
Chapter 6 - Mounting Options ..............................35

www.d.com
4
Chapter 1 Introduction
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or
servicing. After installation or servicing, cover the system chassis before plugging the power
cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
About this Manual
An electronic file of this manual is included in the CD. If not, you can download it and other
product related documentation from our website at www.dfi.com.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper instal-
lation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or damages to the product that
has been modified or altered. Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other com-
ponents. Perform the upgrade instruction procedures described at an ESD worksta-
tion only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chas-
sis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.

www.d.com
5
Chapter 1 Introduction
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 EC510/EC511-KH system unit
• 1 CD disk includes: Drivers/Manual
Optional Items
• Wall Mount kit
• Power Cord
• Power Adapter (100W/120W/160W)
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Safety Precautions
• Use the correct DC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.

www.d.com
6
Chapter 1 Introduction
Chapter 1 - Introduction
Chapter 1
Overview
Key Features
Model Name EC510/EC511-KH
Processor 7th Generation Intel®CoreTM processors
Chipset Intel®CM238, Intel® ® QM175 Chipset
LAN 6 LAN ports (or 4 PoE + 2 LAN ports)
COM 5 COM ports
Display VGA
HDMI/DVI (DVI-D signal)
HDMI or DP (DP available upon request)
USB 4 USB 3.0 & 2 USB 2.0 Type A ports
DIO 16-bit digital input/output
Power 9~36V DC-in
Front Panel
Rear Panel

www.d.com
7
Chapter 1 Introduction
Specifications
Processor 7th Generation Intel®CoreTM Processors, BGA1440 Socket
• Intel®Xeon®Processor E3-1535M v6, Quad Core, 8M Cache, 3.1GHz
(4.2GHz), 45W
• Intel®Core™ i7-7820EQ Processor, Quad Core, 8M Cache, 3.0GHz
(3.7GHz), 45W
• Intel®Core™ i5-7440EQ Processor, Quad Core, 6M Cache, 2.9GHz
(3.6GHz), 45W
• Intel®Core™ i5-7442EQ Processor, Quad Core, 6M Cache, 2.1GHz
(2.9GHz), 25W
• Intel®Core™ i3-7100E Processor, Dual Core, 3M Cache, 2.9GHz, 35W
• Intel®Core™ i3-7102E Processor, Dual Core, 3M Cache, 2.1GHz, 25W
Chipset Intel®CM238 Chipset
Intel®QM175 Chipset
Memory Two 260-pin SODIMM
• Supports dual-channel DDR4 2400MHz
• Supports up to 32GB system memory
• CM238 supports ECC
Graphics Intel®HD Graphics
OpenGL 5.0, DirectX 11, OpenCL 2.1
• Supports these codecs:
HW Decode: HEVC/H.265, H.264, M/JPEG, MPEG2, VC1/WMV9, VP8
(8-bit), VP9 (10-bit)
HW Encode: MPEG2, HEVC/H.265, M/JPEG, VP8
• Output displays:
VGA: resolution up to 1920x1200 @ 60Hz
DVI-I: resolution up to 1920x1200 @ 60Hz
HDMI: resolution up to 4096x2160 @ 24Hz
DP: resolution up to 4096x2304 @ 60Hz
Triple/Dual
Display
VGA (+)
DVI-I (DVI-D signal) / HDMI (HDMI available upon request) (+)
HDMI / DP (DP available upon request)
Storage • Two 2.5" SATA Drive Bay
• SATA 3.0 port with data transfer rate up to 6Gb/s
Chapter 1
Power Power input voltage: 9~36V DC-in (terminal block connector)
Security TPM 2.0 (optional)
Cooling System Fanless with heatsink
Environment • Operating Temperature:
- 0 to 50°C (HDD)
-20 to 60°C (SSD)
-40 to 70°C (optional)
• Storage Temperature:
-20 to 85°C
• Relative Humidity:
5 to 95% RH (non-condensing)
Construction • Metal + Aluminum
Mounting • Wall mount
- Mounting brackets and screws (optional)
Dimensions • 235mm x 102.5mm x 222mm (W x H x D)
Weight • 4.1 kg
OS Support • Linux
• Windows 10 IoT Enterprise 64 Bit
Other Features System Reset, Programmable via Software from 1 to 255 Seconds
Standards and
Certications
• Shock:
Half sine wave 3G, 11ms, 3 shock per axis
• Vibration: IEC68-2-64
• Certications: CE, FCC Class A, Microsoft Azure
Ethernet • 4 x Intel®I210IT PCIe (10/100/1000Mbps)
• 1 x Intel®I211IT PCIe (10/100/1000Mbps)
• 1 x Intel®I219LM with iAMT11.0 PCIe (10/100/1000Mbps) (only
Intel®Xeon®& Core™i7/i5 support iAMT)
Expansion • 1 x PCIe x16 (EC511-KH only) or 1 x PCI (EC510-KH only)
• 1 x M.2 2280 M key (PCIe x4 NVMe, Intel optane memory support)
• 1 x full/half-size Mini PCIe with Mini SIM socket (PCIe & USB)
• 1 x full/half-size Mini PCIe with Mini SIM socket (USB)
Front I/O Ports - One status and one HDD LED
- 2 x RS-232/422/485 (DB-9) (RS-232 with power)
- 2 x USB 2.0 (type A)
- 1 x Power Button
- 1 x Reset Button
- 4 x Antenna Hole
Rear I/O Ports - 6 x GbE (RJ45) or 2 x GbE (RJ45) + 4 x PoE
- 2 x RS-232/422/485 + 1 x RS232 (DB-9)
- 4 x USB 3.0 (type A)
- 1 x VGA
- 1 x DVI (DVI-D signal)/HDMI (HDMI available upon request)
- 1 x HDMI/DP (DP available upon request)
- 1 x Line-out
- 1 x Mic-in (available upon request)

www.d.com
8
Chapter 1 Introduction
Power Button with LED (Green)
Press to power on or power off the system.
Reset Button
Press to reset the system.
HDD LED (Red)
Indicates the status of hard disk drives.
Status LED (Orange)
Indicates system status as below.
Remote Power-on/off Switch Connector
Connects distant power on/off switch.
USB 3.0/2.0 Ports
Connect to USB 3.0 as well as devices based on previous USB versions.
COM Ports
All COM ports can be selected among RS232, RS422 and RS485.
COM1 and COM2 can be selected between RS232 and RS232 with power via jumper settings.
DIO Connector
The DIO connector provides 16-bit digital input/output.
DVI-D (DVI-I connector) / HDMI / VGA Connector
Connects the DVI-I / HDMI / VGA connector of an LCD monitor.
Line-out and Microphone Ports
Connect audio devices such as microphones and speakers.
Gigabit LAN Ports (1~6)
Connect the system to a local area network.
LAN 3~6 can be Power over Ethernet (PoE) that is capable of delivering 15.4W of power to
connected devices.
DC-in
DC 9~36V power input via a terminal block connector.
PCIe Expansion Slot
Provides PCIe or PCI expansion connectivity via a riser card.
Getting to Know the EC510/EC511-KH
Chapter 1
HDD LED
HDD State Disk access
activity Disk drives present or not present
LED Behavior Blink Off
Front I/O Ports
Status LED
Suspend Mode S0 Sleep S4, S5
LED Behavior Always ON Blinking Off
Rear Panel
Notes:
1. Please gently press the power button to avoid possible damages.
2. This port can be in DVI-D or HDMI (HDMI available upon request).
3. This port is a DP/HDMI combo port but can only transmit either HDMI or DP signals (as indicated
on the panel). Please plug in a DP or an HDMI cable with the right orientation and alignment to
avoid damage to the connector. You should feel resistance (due to a pin on the right) if the cable is
not inserted correctly. For detailed instructions, see https://youtu.be/SUj07rfN5l8.
Align this edge with the
left side of the connector
Angled-corner
(up)
Angled-corner
Aligning side
(left) pin
COM4
DC-in
DVI-D(2)
(DVI-I connector)
HDMI(3
USB 3.0 LAN1 LAN2
VGA
Digital IO
Expansion slot
COM3
PoE 1~4
or
LAN 3~6
COM5
Mic-in, Line-out
Front Panel
Antenna holes
COM 2 COM 1
Remote Power Switch
USB 2.0
Power Button
(1)
Status LED
HDD LED
Reset Switch

www.d.com
9
Chapter 1 Introduction
Mechanical Dimensions
Chassis Dimensions
Chapter 1
235.00
102.50
221.20
Front View
Right View
Left View
Rear View
Motherboard Dimensions
Gold finger
PCIE X4
PCIE X16
228
216.70
209.55
50
Gold finger
mini PCIe

www.d.com
10
Chapter 2 Getting Started
Chapter 2 - Getting Started
Chapter 2
Preparing the System
Before you start using the system, you need the following items:
• SATA hard drive
• AC power adapter
• Optical drive (for installing software/drivers)
• Memory module
Installing Devices
The following devices can be installed in the system.
• Memory modules
• SATA hard drives
• Mini PCIe and M.2 cards
• PCIe or PCI expansion cards
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1. Power on the system.
2. After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing an Operating System
To install an OS, you need an optical drive or a USB flash drive and boot from such a device.
Make sure a 2.5” SATA drive is already installed.
1. Refer to the following chapters for information on installing SATA drives.
2. Refer to your operating system manual for instructions on installing the operating system.
Installing the Drivers
The system package includes a CD disk. The CD includes drivers that must be installed to pro-
vide the best system performance. Refer to the Supported Software chapter for instructions on
installing the drivers.