DFI 945G-TMGF User manual

935-945GT1-000
86400522
945G-TMGF
System Board User’s Manual
Carte Mère Manuel Pour Utilisateur
System-Platine Benutzerhandbuch
Manual del Usuario de Placas Base
Ðóêîâîäñòâî ÏîëüçîâàòåëÿÐóêîâîäñòâî Ïîëüçîâàòåëÿ
Ðóêîâîäñòâî ÏîëüçîâàòåëÿÐóêîâîäñòâî Ïîëüçîâàòåëÿ
Ðóêîâîäñòâî Ïîëüçîâàòåëÿ

2
Quick Setup Guide
1
Quick Setup
Guide
Copyright
This publication contains information that is protected by copyright. No part of it
may be reproduced in any form or by any means or used to make any
transformation/adaptation without the prior written permission from the copyright
holders. This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to the
contents or use of this manual and specifically disclaims any express or implied
warranties of merchantability or fitness for any particular purpose. The user will
assume the entire risk of the use or the results of the use of this document.
Further, the manufacturer reserves the right to revise this publication and make
changes to its contents at any time, without obligation to notify any person or
entity of such revisions or changes. © 2005. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification
purpose only and are the properties of the respective owners.
Caution
To avoid damage to the system, use the correct AC input voltage range.....
To reduce the risk of electric shock, unplug the power cord before removing the
system chassis cover for installation or servicing. After installation or servicing,
cover the system chassis before plugging the power cord.
Battery: 1. Danger of explosion if battery incorrectly replaced. 2. Replace only
with the same or equivalent type recommend by the manufacturer. 3. Dispose of
used batteries according to the battery manufacturer’s instructions.
Notice
The system board and accessories you receive in the package may not come
similar to the information stated in this manual. This may differ in accordance to
the sales region or models in which it was sold. For more information about the
standard package in your region, please contact your dealer or sales
representative.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accord-
ance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables must be used in order to comply with the emission
limits.

3
1
Quick Setup Guide
Quick Setup
Guide
Table of Contents
Chapter 1
Quick Setup Guide.............................................
Chapter 2
English......................................................................
Chapter 3
Français....................................................................
Chapter 4
Deutsch...............................................................................
Chapter 5
Español............................................................................
Chapter 6
Ðóññêèé.......................................................................
4
15
19
22
26
29
The user’s manual in the provided CD contains detailed information about the system board. If, in some
cases, some information doesn’t match those shown in this manual, this manual should always be re-
garded as the most updated version.
Le manuel d’utilisateur dans le CD muni contient renseignement détaillé au sujet de carte de système. Si,
en quelque cas, quelque renseignement n’appareille de ce que dit dans ce manuel, ce manuel doit
toujours être considéré comme la plus nouvelle version.
Das Benutzerhandbuch in der angebotenen CD enthält detaillierte Informationen über die Hauptplatine.
Wenn in manchen Fällen manche Informationen nicht denjenigen Informationen dargestellt in diesem
Handbuch entsprechen, soll dieses Handbuch als die meist aktualisierte Ausgabe gelten.
El uso explicativo contene información detalle sobre la sistema board en el CD preparativo. Si en algún
caso, la información no es igual con el uso explicativo, necesita ver el uso explicativo, esque es más
nuevo.
 ðóêîâîäñòâå ïîëüçîâàòåëÿ íà ïðåäîñòàâëÿåìîì CD äèñêå ñîäåðæèòñÿ ïîäðîáíàÿ
èíôîðìàöèÿ î ìàòåðèíñêîé ïëàòå. Èíîãäà íàïå÷àòàííîå ðóêîâîäñòâî ìîæåò íå
ñîâïàäàòü ðóêîâîäñòâîì íà CD, òàê êàê ïîñëåäíåå íàèáîëåå ÷àñòî îáíîâëÿåòñÿ è
ÿâëÿåòñÿ ñàìûì ñâåæèì.

4
Quick Setup Guide
1
Quick Setup
Guide
System Board Layout
Chapter 1 - Quick Setup Guide

5
1
Quick Setup Guide
Quick Setup
Guide
System Memory
DDR2_1
DDR2_2
DDR2_3
DDR2_4
Channel A - DDR2_1 and DDR2_2
Channel B - DDR2_3 and DDR2_4
DIMMs are on the same channel.
DIMMs in a channel can be identical or
completely different.
Not all slots need to be populated.
DIMMs of different memory configurations
are on different channels.
Odd number of slots can be populated.
DIMMs of the same memory configuration
are on different channels.
In single channel, requires even number or
rows (side of the DIMM) populated.This
mode can be enabled with 1 SS, 2 SS or
2 DS.
In VSC mode, both channels must have
identical row structure.
Single Channel
Virtual Single
Channel
Dual Channel
Dynamic Mode
Addressing

6
Quick Setup Guide
1
Quick Setup
Guide
Jumpers
Clear CMOS Data
Important:
The 5VSB power source of your power supply must support
≥ 720mA.
PS/2 Power Select
2-3 On:
Clear CMOS Data
1-2 On: Normal
(default)
X
JP4
132
132
X
JP3
2-3 On: 5VSB
1-2 On: 5V
(default)
1
3
2
1
3
2

7
1
Quick Setup Guide
Quick Setup
Guide
Rear Panel I/O Ports
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2
USB ports, the 5VSB power source of your power supply must
support ≥ 1.5A. If you are using the Wake-On-USB Keyboard/Mouse
function for 3 or more USB ports, the 5VSB power source of your
power supply must support ≥ 2A.
USB Power Select
X
USB 1-4
(JP2)
2-3 On: 5VSB
1-2 On: 5V
(default)
X
USB 5-8
(JP1)
2-3 On: 5VSB
1-2 On: 5V
(default)
1
3
2
1
3
2
132 132
PS/2
Mouse Parallel
COM VGAPS/2 K/B
LAN
1394_1
USB 1-2 USB 3-4
Line-in
Line-out
Mic-in

8
Quick Setup Guide
1
Quick Setup
Guide
I/O Connectors
IEEE 1394
1394_1
W
W
1394_2 1
2
10
9
TPA+TPA-
Ground Ground
TPB- TPB+
Key
+12V
+12V
Ground
USB 4
USB 3
USB Ports
W
USB 2
USB 1
W
USB 5-6
W
USB 7-8
1
210
9
VCC VCC
-Data -Data
+Data +Data
Ground Ground
KeyN. C.

9
1
Quick Setup Guide
Quick Setup
Guide
2-channel
Line-in
Line-out
Mic-in
4-channel
Line-in
Front R/L
Rear R/L
6-channel
Center/Subwoofer
Front R/L
Rear R/L
Light Blue
Lime
Pink
Front audio
W
Audio (Rear Audio and Front Audio)
Mic-in
Line-out
Line-in
W
1
Mic
N. C.
AuD_R_Out
N. C.
AuD_L_Out
GND
AuD_Vcc
Key
210
9
AuD_R_Return
AuD_L_Return
Rear Audio
CD-in Internal Audio Connector
W
1
4
Left audio
channel
Right audio
channel
Ground
Ground

10
Quick Setup Guide
1
Quick Setup
Guide
S/PDIF
W
15
+5V
Key
SPDIF out
GND
SPDIF in
Floppy Disk Drive Connector
X
34 33
21

11
1
Quick Setup Guide
Quick Setup
Guide
Serial ATA Connectors
X
SATA 2
SATA 1
SATA 4
SATA 3
GND
TXP
TXN
GND
RXN
RXP
GND
17
17
17
17
IDE Disk Drive Connector
X
40 39
21

12
Quick Setup Guide
1
Quick Setup
Guide
Note:
The sequence of the pin functions on some IR cable may be
reversed from the pin function defined on the system board. Make
sure to connect the cable connector to the IR connector according to
their pin functions.
IrDA Connector
X
1
5
VCC
N. C.
IRRX
Ground
IRTX
Cooling Fan Connectors
X
CPU fan
X
Chassis fan
41
Sense
Power
Ground
Speed
Control
1
3
Ground
Power
Sense

13
1
Quick Setup Guide
Quick Setup
Guide
Important:
To ensure that adequate power is provided, we strongly recommend
that you use a minimum of 400 Watt (or greater) power supply.
Power Connectors
X
X
131
12 24
+3.3VDC
+3.3VDC
COM
+5VDC
COM
+5VDC
COM
PWR_OK
+5VSB
+12VDC
+12VDC
+3.3VDC
+3.3VDC
-12VDC
COM
PS_ON#
COM
COM
COM
NC
+5VDC
+5VDC
+5VDC
COM
+12V
12
43
Ground
Ground
+12V
PCI Express x16 and x1 Slots
PCI Express x16
PCI Express x1

14
Quick Setup Guide
1
Quick Setup
Guide
Front Panel Connectors
X
J19
PWR-LED
ATX-SW
HD-LED
RESET
SPEAKER
21
2019
Pin
3
5
14
16
8
10
18
20
7
9
13
15
17
19
2
4
6
HD-LED
(Primary/Secondary IDE LED)
Reserved
ATX-SW
(ATX power switch)
Reserved
RESET
(Reset switch)
SPEAKER
(Speaker connector)
PWR-LED
(Power/Standby LED)
Pin Assignment
HDD LED Power
HDD
N. C.
N. C.
PWRBT+
PWRBT-
N. C.
N. C.
Ground
H/W Reset
Speaker Data
N. C.
Ground
Speaker Power
LED Power (+)
LED Power (+)
LED Power (-) or Standby Signal

15
2
English
English
Chapter 2 - English
Features and Specifications
Processor
• Intel®Pentium®4 Prescott processor
- Hyper-Threading Technology
- 533MT/s, 800MT/s (200MHz) and 1066MT/s (266MHz)
system bus interface
• Socket LGA 775 (LAN Grid Array)
Chipset
• Intel chipset
- North bridge: Intel®945G Express chipset
- South bridge: Intel®ICH7
System Memory
• Four 240-pin DDR2 DIMM sockets
• Supports DDR2 533 and DDR2 667 DIMMs
• Supports dual channel (128-bit wide) memory interface
• Supports up to 4GB system memory
• Supports non-ECC x8 and x16 DIMMs
• Supports up to 512Mb DRAM densities
• Supports unbuffered DIMMs
BIOS
• Award BIOS
• 4Mbit flash memory
Energy Efficient Design
• Supports ACPI specification and OS Directed Power
Management
• Supports ACPI STR (Suspend to RAM) function
• Wake-On-Events include:
- Wake-On-PS/2 Keyboard/Mouse
- Wake-On-USB Keyboard/Mouse
- Wake-On-Ring (external modem)
- Wake-On-LAN
- RTC timer to power-on the system
• AC power failure recovery

16
English
2
English
Hardware Monitor
• Monitors CPU/system temperature and overheat alarm
• Monitors Vcore/V3SB/Vcc3/Vcc5/12V/V5SB/VBAT voltages
• Monitors the speed of the CPU/system fan
• CPU Overheat Protection function monitors CPU temperature
and fan during system boot-up - automatic shutdown upon
system overheat
Onboard VGA Features
• Built-in Intel Graphics Media Accelerator 900
Onboard Audio Features
• 6-channel audio CODEC
• Full-duplex codec with independent variable sampling rate
• True stereo line level outputs
• S/PDIF-in/out interface
Onboard LAN Features
• Realtek RTL8110SB PCI Gigabit LAN controller
• Supports 10/100/1Gbps
• IEEE 802.3ab compliant
• Integrated power management functions
• Supports wire for management
Serial ATA Interface
• Supports four SATA (Serial ATA) interfaces which are compliant
with SATA 1.0 specification
• SATA speed up to 3Gb/s
IEEE 1394 Interface
• Supports two 100/200/400 Mb/sec ports
IDE Interface
• One IDE connector supports up to two UltraDMA100Mbps
hard drives

17
2
English
English
Rear Panel I/O Ports
• 1 mini-DIN-6 PS/2 mouse port
• 1 mini-DIN-6 PS/2 keyboard port
• 1 DB-9 serial port
• 1 DB-25 parallel port
• 1 DB-15 VGA port
• 1 IEEE 1394 port
• 1 RJ45 LAN port
• 4 USB 2.0/1.1 ports
• Line-in, line-out and mic-in jacks
I/O Connectors
• 2 connectors for 4 additional external USB 2.0/1.1 ports
• 1 connector for 1 external IEEE 1394 port
• 1 front audio connector for external line-out and mic-in jacks
• 1 CD-in internal audio connector
• 1 S/PDIF connector
• 1 IR connector
• 4 Serial ATA connectors
• 1 IDE connector
• 1 floppy connector
• 1 24-pin ATX power connector
• 1 4-pin ATX 12V power connector
• 1 front panel connector
• 2 fan connectors
Expansion Slots
• 1 PCI Express x16 slot
• 1 PCI Express x1 slot
• 2 PCI slots
PCB
• microATX form factor
• 24.4cm (9.6") x 24.4cm (9.6")

18
English
2
English
Package Checklist
The system board package contains the following items:
;One system board
;One IDE cable
;One floppy cable
;Two Serial ATA data cables
;One Serial ATA power cable
;One I/O shield
;One “Mainboard Utility” CD
;One user’s manual
If any of these items are missing or damaged, please contact your
dealer or sales representative for assistance.

19
3
Français
Français
Chapter 3 - Français
Caractéristiques et Spécifications
Processeur
• Les processeurs Intel®Pentium®4 Prescott
- Intel Hyper-Threading Technologie
- Interface du bus système 533MT/s, 800MT/s (200MHz) et
1066MT/s (266MHz)
• Socket LGA 775 (LAN Grid Array)
Chipset
• Intel chipset
- Pont nord: Intel®945G Express chipset
- Pont sud: Intel®ICH7
Mémoire Système
• 4 socles DIMM DDR2 240-pin
• Supporte DDR2 533 et DDR2 667 DIMMs
• Supporte l’interface de mémoire deux canaux (128-bit)
• Supporte jusqu’à 4 GB de mémoire système
• Supporte exclusivement les modules DIMM non-ECC x8 et x16
• Supporte une densité de RAM jusqu’à 512Mb
• Supporte les DIMM non-tamponnés
BIOS
• Compatible avec Award BIOS
• Mémoire Flash 4Mbit
Design à Haut Rendement Énergétique
• ACPI STR (Suspend to RAM) fonction
• Réveil-Sur-PS/2 Clavier/Souris et Réveil-Sur-USB Clavier/Souris
• Eveil Sonnerie et Réveil Par Le Réseau
• Minuterie RTC pour allumer le système
• Récupération après Défaillance d’Alimentation CA
System Health Monitor Fonctions
• Gère l’alarme de température et de surchauffe de CPU/système
• Gère l’alarme de voltage et d’échec de Vcore/V3SB/Vcc3/Vcc5/
12V/V5SB/VBAT
• Gère la vitesse de ventilateur du ventilateur de CPU/système

20
Français
3Français
Français
• Protection du CPU - supporte la mise hors circuit automatique
en cas de surchauffage du système
Fonctionnalités Graphiques Intégrées
• Intel Graphics Media Accelerator 900 intégrées
Fonctionnalités Audio Intégrées
• 6-canaux audio CODEC
• Codec full-duplex avec fréquence d’échantillonnage variable
indépendante
• Sorties de niveau de lignes stéréo vraies
• Interface entrée/sor tie S/PDIF
Fonctionnalités LAN Intégrées
• Realtek RTL8110SB PCI Gigabit LAN Controleur
• Supporte 10/100/1Gbps
• IEEE 802.3ab compatible
• Fonctions de gestion d’alimentation intégrées
• Support câble pour la gestion
Interface Serial ATA
• Supportant 4 interface SATA (Serial ATA) compatible avec la
spécification SATA 1.0
• bande passante à 3Gbps
Interface IEEE 1394
• Supporte 2 ports 100/200/400 Mb/séc
Contrôleur IDE
• Supporte des disques durs jusqu’à UltraDMA 100Mbps
Le Panneau des Ports Entrée/Sortie en Arrière
• 1 port souris PS/2 et 1 port clavier PS/2
• 1 port de DB-9 série
• 1 port parallèle DB-25
• 1 port de DB-15 VGA
• 1 port IEEE 1394
• 1 port RJ45 LAN
• 4 ports USB 2.0/1.1
• Line-in, line-out et mic-in prises audio