Rize The cresta... User manual

Photos are for illustration purposes only. Not responsible for typographical errors.

Model Number:

RI-ABF-A18-WWM-ESF-107-L-U-AC-LM-CC4B

This product and all our bedding products are covered by one or more of the following issued

and pending U.S. patents including Nos. 7448100, D657157, D663542, D657158, D657156,

8209801, 8209800, D663544, D663543 and other patents pending.

Serial Number: ___ __________ ______

(Place your serial number here for ready reference)

OWNER’S MANUAL

The

Lumbar/Lounge

Wireless Adjustable Bed with

Advanced Leg-Lowering

“LOUNGE” Feature

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:10 PM Page 1

Cresta

The

Table of Contents

Safety Precautions 1

Parts List 3

Installation Guide 4

Wireless Hand Control Operation Guide 6

Emergency Power Down Operation Guide 9

Troubleshooting 10

Warranty & Registration 12

Model Number: RI-ABF-A18-WWM-ESF-107-L-U-AC-LM-CC4B

The

Lumbar/Lounge

Wireless Adjustable Bed

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:10 PM Page 2

Cresta

The

Safety Precautions

ATTENTION!

IMPORTANT SAFETY INSTRUCTIONS.

PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS PRODUCT.

Always unplug this adjustable bed frame from the electrical outlet before any cleaning or maintenance of the bed frame. To

safely disconnect, make sure all controls are in the off position, then remove the plug from the outlet.

Keep cord away from heated surfaces. Keep air openings free of lint, hair and the like - never operate when air openings are

blocked. Never drop or insert any object into any opening. Use only indoors.

Cease use of this bed frame and contact the Adjustable Bed base center for repair if: (1) it has a damaged cord or plug, (2) it is

not working properly, (3) it has been dropped or damaged, or (4) it has been dropped into water.

ELECTRICAL SAFETY

To reduce the risk of electric shock, electrical fire, or faulty operation of this product, your Adjustable Bed features a polarized plug

meant to be used only with a grounded electrical outlet. If this plug does not fit into your outlet, contact a qualified electrician to

install a properly grounded outlet. Failure to use a properly grounded outlet for this product will compromise this important

grounding safety feature. The use of adapters is not recommended unless the outlet is checked by a qualified electrician to ensure

the proper grounding of the adapter. Please note: Unauthorized modifications to this product could void the electrical portion of

your warranty.

This Adjustable Bed is designed exclusively for in-home use.

HOSPITAL DISCLAIMER: It is NOT designed for hospital use and is NOT designed to meet hospital standards.

Do not use this bed with TENT TYPE oxygen therapy equipment or use near explosive gases.

GROUNDING SAFETY

IMPORTANT SAFETY FEATURES

IN-HOME USE ONLY

FOR OPTIMAL SAFETY, YOUR ADJUSTABLE BED SHOULD BE PLUGGED INTO A SURGE PROTECTOR

(not supplied with this Adjustable Bed).

Weight fail safe feature: In the case that an overload of weight is placed on the head or foot mechanism, the control unit will

automatically stop all functions. The control unit will automatically resume all functions 30 seconds after excess weight is removed.

Weight Restrictions: The recommended weight limits on our adjustable beds are:

Twin/TXL/Split QN/Split CA King: 575 Pounds, Full/FXL: 600 Pounds, Queen: 650 Pounds.

WARRANTY WARNING!

This bed is specifically designed to require no maintenance by you, the user. Any opening or tampering with the control box,

motors or hand controls (with the exception of the battery compartment if equipped) will result in a void of the warranty.

Only those authorized may conduct repairs or part replacement on your adjustable bed.

Wireless Adjustable Bed

The

Lumbar/Lounge

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:10 PM Page 3

Cresta

The

Wireless Adjustable Bed

Safety Precautions-cont’d

PRODUCT RATINGS

Immediately dispose of all packing materials as it can pose a smother risk to small children and pets. Injury could occur also if

children or pets are permitted to play on or under the bed. Do not allow children to operate this bed without adult supervision.

SMALL CHILDREN AND PETS WARNING

SAVE THESE INSTRUCTIONS!

Proper operation of your Adjustable Bed is necessary to ensure the long life and

durability you expect from a high-quality product. The manufacturer has tested

and inspected this product prior to shipment.

IMPORTANT SAFETY FEATURES cont’d

Locking caster feature: This Adjustable Bed may be equipped with special locking casters. For your safety, these casters will prevent bed

movement when all casters are in the locked position. To lock casters, push down the safety latch on the caster. To resume product mobility,

lift the safety latch up.

Please note: If your Adjustable Bed is positioned on a hard floor surface such as hardwood or tile, it is strongly recommended that rubber caster

cups or carpet squares are placed under the casters in addition to locking them in place. Casters will not roll when locked, but may slide on an

uncarpeted surface.

FCC compliance device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s right to

operate the device.

The input transformer voltage is AC120V 60HZ; the output voltage is DC24V 3A. In the case of a short-circuit, a fuse on the transformer

will blow to protect the electrical equipment of the device (Fuse: 1A~1.5A.). Should this occur, you should seek professional assistance to

fix the problem, and call Customer Care at: 1-877-826-8757

RADIO FREQUENCY IS 433.92 MHZ.

It is possible that the (optional) vibrating feature of this bed may be misinterpreted by some pacemakers as movement and/or

exercise. This is common with any product that produces a vibrating motion, and may or may not affect your pacemaker.

Please consult your physician with any concerns.

CONSUMERS WITH PACEMAKERS

Wireless Adjustable Bed

Lift Motor Restrictions: The lift motors in this bed are NOT designed to operate continuously for more than three (3) minutes over a thirty (30)

minute time period, or approximately 10% duty cycle. To ensure reliable functionality and full life of this product, do not attempt to exceed

these limits.

NOTE: Attempting to circumvent or exceed this rating will shorten the life expectancy of the product and may void the warranty.

The structure of the bed will support the recommended weight when distributed evenly across the bed. The head and foot sections are

not designed to individually support or lift this amount of weight. For optimal performance, entering and exiting the adjustable bed with

the bed in the flat or level position is recommended.

NOTE: Exceeding the recommended weight restrictions could damage your adjustable bed and void your warranty.

The

Lumbar/Lounge

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:10 PM Page 4

Cresta

The

Wireless Adjustable Bed

NOTE: Before discarding any packing materials,

check the adjustable bed frame carton and verify all

items in the parts list are included:

**Only in TXL, SCK, SQ models.

Parts List

†Indicates Part is attached to Base *Indicates Part is attached to the side of the frame

M. Velcro Leg Strap (1)**

Wireless Adjustable Bed

A. Remote Control (1) B. “Custom-Clip”

Mattress Retainer Bracket (4)

C. Post Bed Legs (2)

I. 5/16 Inch Washer (12)

D. Inner Headboard Bracket (2)

E. Outer Headboard Bracket (2) G. Headboard Bracket Bolt (6)

J. 5/16 Inch Nut (6)

L. Wrench (1)

M. Lounger Post Leg (2) N. Knob Bolt (2)

O. Spring Washer (2)

P. Velcro Leg Strap (1)** Q. AC Outlet (2)*

K. Allen Key Wrench (1)

The

Lumbar/Lounge

CAUTION: Electric Plug output AC 120V.

Do not exceed Max Power: 500 W

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:10 PM Page 5

Cresta

The

Wireless Adjustable Bed

Cresta

The

Wireless Adjustable Bed

STEP 10. Assemble the Headboard Bracket

i. Use the hand control to elevate the head of the bed so

the bed base frame is reachable.

iv. When headboard brackets are assembled, make sure there is a space of 1.5 (38.1 mm) to 2 inches (50.8 mm)

between the edge of the bed base and the headboard brackets.

v. Securely fasten the headboard bolts (not included with your adjustable bed) to the end of the headboard bracket assembly.

vi. Measure the distance from the center of one mounting hole in the headboard bracket assembly to the center of the other.

vii. If you need to adjust the headboard brackets, unscrew the bolts holding the outer headboard brackets and move them

the necessary distance. Reinstall the bolts and securely tighten.

STEP 11.

Place your mattress on the adjustable bed frame surface. Your adjustable bed and headboard installation is now complete.

If the bed comes with a programming option, turn to the Wireless Hand Control Operation Guide ( located on pages 6 and 7) to proceed.

IMPORTANT NOTES:

Failure to follow the installation steps as they appear in this guide could result in damage to your adjustable bed frame.

Make sure to position the bottom of the headboard cross member no more than

3 inches (76.2 mm) between the headboard and the top of the mattress.

iii. Place the open side of the outer headboard bracket (E) onto

the exposed square tube of the inner headboard bracket (D) to

create a tight fit between (D) and (E). Insert a retainer bolt (G)

fitted with a 5/16 inch washer (I) into the outer headboard

bracket (E) and through the inner headboard bracket (D). Hand

tighten using a 5/16 inch washer (I) and a 5/16 inch nut (J).

(Leave loose enough for adjusting.) Repeat on

the other side.

ii. Slide the inner headboard bracket (D) horizontally with the

“C” opening facing down under the Crossbar. Position the

Bracket (D) in the guide peg on the bottom of the Crossbar.

Insert a headboard bolt (G) fitted with a 5/16 inch washer (I)

thru the pre-drilled hole in the Crossbar & into the pre-drilled

slotted hole in the “C” channel Inner Headboard Bracket.

Tighten in place with a 5/16 inch washer (I) and 5/16 inch nut

(J). Repeat on the other side.

POST LEG STRAP VELCO

Wireless Adjustable Bed

To help prevent separation when using King Size (2 TXL)

California King Size (2 SCK) or split Queen Size (2 SQ).

Please use the enclosed Velcro Straps.

1. Simply wrap the legs together (Front & Back) tightly

using the velcro straps.

2. Fastening the straps will help prevent movement &

maintain stability.

Velcro Leg Straps (Optional: To avoid Base Separation)

The

Lumbar/Lounge

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:11 PM Page 7

Cresta

The

Wireless Adjustable Bed

Wireless Hand Remote Operation

LED Signature Light

A. Raises the Head of the Bed

B. Lowers the Head of the Bed

H. Returns Head & Foot to FLAT

Position (hold 2 seconds)

P. Increases Lumbar Support Q. Decreases Lumbar Support

I. Increases the Intensity

of Vibration (Head)

J. Decreases the Intensity

of Vibration (Head)

N. Turns on Massage

Wave 1,2 or 3

M. Stops Massage

E. Anti-Snore

C. Raises the Foot of the Bed

D.Lowers the Foot of the Bed

G. Zero Gravity

F. Lounge

K. Increases the Intensity

of Vibration (Foot)

L. Decreases the Intensity

of Vibration (Foot)

FOR YOUR SAFETY, READ THE OWNER’S MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS PRODUCT. ELECTRIC SHOCK MAY OCCUR IF

ELECTRICAL COMPONENTS ARE NOT INSTALLED OR OPERATED ACCORDING TO THESE GUIDELINES.

Head and Foot Position Adjustments (A, B, C, D)

• Use to raise or lower the head and foot sections of your adjustable bed.

Anti-Snore Relief (E)

• Press to gently raise head section to allow easier air intake which can help reduce snoring.

Lounge Feature (F)

• Press the Lounge Button to lower your leg area helping remove stress & tension from your lower back in a Chaise Lounge Position.

Zero Gravity (G)

• This function allows your legs to be lifted to a position slightly higher than

the chest. This allows blood to flow back to the heart, reducing stress and fatigue.

Bed “Flat” Button (H)

• Press down and hold for 3 seconds to return bed to the flat position.

Head and Foot Massage Adjustments ( I, J,K,L)

•

Use to activate the massage feature on the head and foot of the bed (starting at intensity 4 of 8). Gradually increase or decrease intensity of

massage vibration by pressing the appropriate button. The lowest setting on each massage unit will turn off the respective vibration. The

massage feature is programmed with an Auto Shut-Off Timer that will automatically turn off the massage after 15 minutes of continuous use.

Wireless Adjustable Bed

O. Under

Bed Light

The

Lumbar/Lounge

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:11 PM Page 8

Cresta

The

Wireless Adjustable Bed

NOTE:

This bed may show minor intermittent performance because of typical RF interference.This is normal in the operation of the bed, not a defect.

• The buttons are backlit, when pressed, to aid in the visibility of the remote in low light environments.

• It is not necessary to face the receiver to operate the remote control. Remote signal is best transmitted within

9 feet (3 meters) of the receiver.

SAFETY

• In the case that an overload of weight is placed on the head or foot mechanism, the control unit will automatically stop all

functions. The control unit will automatically resume all functions 30 seconds after excess weight is removed.

• Massage motors will automatically shut off after running continuously for 15 minutes. All massage functions will be

operational again after 5 minutes.

• The input transformer voltage is AC120V 60HZ, the output voltage is DC24V 3A. In the case of a short-circuit, a fuse on the

transformer will blow to protect the electrical equipment (Fuse: 1A~1.5A.). Should this occur, you MUST seek professional

assistance to replace the fuse. Call Customer Care at: 1-877-826-8757

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Important Note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device

is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and

void user’s authority to operate the device.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

REMOTE FEATURES

• The Adjustable Bed uses a RF (Radio Frequency) hand control system.

Wireless Hand Remote Operation

Stop Button (M)

• Hold down for 2 seconds to stop massage.

REMEMBER: YOU MUST STOP MASSAGE BEFORE ALTERNATING BETWEEN MASSAGE FUNCTIONS.

Wave Massage Adjustments (N)

• Activates both units to wave mode massage. NOTE: You must stop the massage in order to activate another

massage setting such as full body or another wave massage.

Underbed LED Light (O)

• Press this button on the back of your remote to create a halo of light that helps you safely navigate in & out of bed during the night.

Lumbar Adjustments (P,Q)

• Activates the power Lumbar System which greatly increases or decreases lower back support.

Wireless Adjustable Bed

Continued

The

Lumbar/Lounge

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:11 PM Page 9

Cresta

The

Wireless Adjustable Bed

Cresta

The

Cresta

The

Wireless Adjustable Bed

1. Locate and remove the 9 volt battery cover.

3. Replace the battery cover.

2. Install two (2) Alkaline 9 volt batteries.

(Not Included)

Figure 5: 9 volt battery cover

Your adjustable base is equipped

with an emergency lowering feature. Follow the steps below in the

event that your base is in the raised position during a power outage.

Figure 6: Install the 9 volt batteries

Figure 7: Replace battery cover

Figure 8: Lower the bed using the 9 volt

battery backup system

NOTE:

THE TWO (2) 9 VOLT BATTERIES ARE ONLY RATED FOR SINGLE USE. AFTER

THE EMERGENCY LOWERING, REPLACE WITH NEW ALKALINE BATTERIES.

Wireless Adjustable Bed

Wireless Emergency Power Down Feature

The

Lumbar/Lounge

4. When the two (2) 9-Volt batteries are installed in the

power supply, and there is a power failure, the LEARN

button on the Power Supply can be used to move the

bed to the flat position.

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:11 PM Page 11

Cresta

The

Wireless Adjustable Bed

Cresta

The

Wireless Adjustable Bed

Continued

In the event the adjustable bed fails to operate, investigate the

symptoms and possible solutions provided in the chart below:

Activating Head or Foot Lift Function causes

"pulsing" or "stuttering" when operating feature.

Troubleshooting

IF YOU EXPERIENCE ANY TROUBLE WITH YOUR

BED WITHIN THE WARRANTY PERIOD,

PLEASE CONSULT THE TROUBLESHOOTING GUIDE PROVIDED WITH YOUR BED

AND ONLINE (IF APPLICABLE). IF PROBLEMS PERSIST, PLEASE CALL:

CUSTOMER SERVICE TOLL FREE NUMBER

1-877- 826-8757

Please Have Your Receipt Ready And Available

THANK YOU AND ENJOY YOUR ADJUSTABLE BED!

SYMPTOM SOLUTION

1) Check batteries and installation in Hand Remote.

2) Assure that the Function Key is pressed

Directly & Firmly.

3) Radio Frequency Interference from other remotes or

electronic devices may be affecting normal operation.

Massage Motors seem excessively

loud during operation. 1) Hard surface flooring may cause added vibration.

To correct, place carpet pieces or rubber Furniture

Cups under each leg or caster of the bed.

2) Elevate the head or foot section a short distance

(with the hand control) to realign the lift/lower

mechanisms with the bed support platform.

3) Check that the bed is not in direct contact with a

wall, nightstand, or other object that may cause

vibration or noise.

4) If Adjustable Bed is installed on top of a bed

frame, check that the massage motors are not causing

bed frame (or bed frame components) to vibrate or

rattle.

5) Check that the headboard attachment hardware

is tightened firmly (if used).

Wireless Adjustable Bed

The

Lumbar/Lounge

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:12 PM Page 13

Cresta

The

Wireless Adjustable Bed

WARRANTY

20-Year Premium Limited Warranty for Adjustable Beds

Wireless Adjustable Bed

CUSTOMATIC ADJUSTABLE BEDZ®, (CUSTOMATIC ADJUSTABLE BEDZ®) warrants this adjustable bed to the consumer who is the original purchaser

(the “purchaser,” subject to the terms and conditions set forth herein). This warranty begins on the “warranty commencement date,” or the

purchase date for new and unused adjustable beds. For adjustable beds that have been used either as floor or display models, the “warranty

commencement date” is the date the bed was manufactured. Therefore, a floor or display model bed is covered by a portion of the limited

20-year warranty. The purchaser must show original proof of purchase for warranty to be valid. If proof of purchase is not presented, CUSTOMATIC

ADJUSTABLE BEDZ®holds full right to determine whether the adjustable bed is covered by the warranty. In so doing, CUSTOMATIC ADJUSTABLE

BEDZ®has the right to use the manufacturing date as the warranty commencement date.

The 20-Year Limited Warranty is extended solely to the original purchaser. This warranty is not transferrable.

FULL 3-YEAR WARRANTY (Parts)

This adjustable bed is warranted against defects in the workmanship or materials for a period of three years from the warranty commencement date.

Upon notice during the first three years after the warranty commencement date, CUSTOMATIC ADJUSTABLE BEDZ®will replace any defective

adjustable bed part based on the criteria listed below.

YEAR 1: Full Coverage of Parts & Labor

This adjustable bed is warranted against workmanship and craftsmanship defects or defective materials for up to one (1) year from the warranty

commencement date. When notified by purchaser within the first year, CUSTOMATIC ADJUSTABLE BEDZ®will supply replacements (at no cost to

the purchaser) for any defective or malfunctioning adjustable bed part. CUSTOMATIC ADJUSTABLE BEDZ®must authorize that the part is defective

or malfunctioning before replacement parts are supplied to purchaser or any labor costs are absorbed. Once CUSTOMATIC ADJUSTABLE BEDZ®

approves the part is defective or malfunctioning, they will absorb the costs for pre-authorized labor and any transportation costs associated with the

repair/replacement of any parts. For this one (1) year warranty to be valid, any and all defective or malfunctioning parts must be returned by the

original purchaser (or by an authorized CUSTOMATIC ADJUSTABLE BEDZ®in-home technician or agent) to CUSTOMATIC ADJUSTABLE BEDZ’s®

Customer Care Center within 15 days of purchaser receiving replacement parts.

YEARS 2 And 3: Full Coverage of Parts Only.

After the first year from the warranty commencement date, and up to three (3) years from the warranty commencement date, CUSTOMATIC

ADJUSTABLE BEDZ®will provide replacement parts for any defective or malfunctioning adjustable bed part upon receiving written notice from the

original purchaser. This two (2) year warranty is only valid once any and all defective or malfunctioning parts are returned by the original purchaser to

CUSTOMATIC ADJUSTABLE BEDZ®’s Customer Care Center within 15 days of purchaser receiving replacement parts. The original purchaser is

responsible for all service, transportation, labor and shipping & handling costs related to the delivery and/or replacement of the defective or

malfunctioning part(s).

YEARS 4 Through 20: Prorated Coverage of Non Electrical Parts Only.

After the third year of the warranty commencement date, and up to twenty (20) years from the warranty commencement date, CUSTOMATIC

ADJUSTABLE BEDZ®will issue replacements (upon terms and conditions described below) for any mechanical bed part found to be defective or

malfunctioning upon receiving written notice from the original purchaser. This does not apply to electronics, electrical components, massage motors

and lift motors. Purchaser will be required to pay 1/17th of the (then) current replacement cost of the part multiplied by the number of years past the

third year from the warranty commencement date. CUSTOMATIC ADJUSTABLE BEDZ®will take responsibility for the remaining cost of the replace-

ment part. This seventeen (17) year warranty is only valid once any and all defective or malfunctioning parts are returned by the original purchaser to

CUSTOMATIC ADJUSTABLE BEDZ’s®Customer Care Center within 15 days of purchaser receiving replacement parts. Purchaser holds responsibility

for all labor and transportation costs related to the replacement of the defective part up to twenty (20) years after the commencement date. After the

twentieth year, purchaser will be responsible for the entire cost of repair and replacement of all defective parts and materials, including service and

transportation costs associated with the repair or part replacement.

ADDITIONAL TERMS AND CONDITIONS

This warranty is considered void: 1) if any damage to the adjustable bed is caused by the purchaser; 2) if any unauthorized repair or replacement of

parts has taken place; 3) if the adjustable bed has been handled incorrectly in transit or otherwise, subjected to physical or electrical abuse or misuse,

or otherwise operated in a way that does not adhere to the guidelines for proper operation and maintenance outlined in the Owner’s Manual, this

warranty, and any other applicable text published or approved by CUSTOMATIC ADJUSTABLE BEDZ®; 4) in relation to any damage to mattresses,

fabric, cables, electrical cords or items supplied by dealers. Contact the dealer or relevant party for warranty information on these items; 5) if any

unnecessary service calls have taken place, including fees for in-home service calls solely for the consumer’s educational purposes or for finding an

unsatisfactory power connection; 6) if the recommended weight restrictions (Twin/TXL/Split QN/Split CA King: 575 Pounds, Full/FXL: 600 Pounds,

Queen: 650 Pounds) and guidelines for proper distribution of weight outlined in the Owner’s Manual are not followed.

Repairs to or replacement of the adjustable bed or its components under the terms of this limited warranty will apply to the original warranty period

and will not serve to extend such period.

The decision for the repair or replacement of defective parts under this warranty is at the option and sole discretion of CUSTOMATIC

ADJUSTABLE BEDZ®.

REPAIR OR REPLACEMENT OF ADJUSTABLE BED PARTS WILL BE THE SOLE REMEDY OF THE PURCHASER. CUSTOMATIC ADJUSTABLE BEDZ®, AND

THEIR PARENTS, SUBSIDIERIES, DIVISIONS, AFFILIATES OR AGENTS HOLD ABSOLUTELY NO OR ANY SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES OR FOR ANY OTHER DAMAGE, CLAIM, OR LOSS NOT EXPRESSLY COVERED BY THE TERMS OF THIS WARRANTY.

ADJUSTABLE BEDZ

CUSTOM SLEEP

TO FIT YOUR LIFE

The

Lumbar/Lounge

AVANTE-LUMBAR-LOUNGER w/Changes_Layout 4 8/27/15 6:12 PM Page 14

Cresta

The

Wireless Adjustable Bed

SURVEY

Gender:

Age:

18-30 31-40

Health Comfort Other

Advertising A friend Store

Article/Review Internet Other

41-50 51-60

61-70 71 & up

Reason for purchasing an adjustable bed:

How did you find out

about CUSTOMATIC Bedz:

WARRANTY REGISTRATION FORM

ADJUSTABLE BEDZ

CUSTOM SLEEP

TO FIT YOUR LIFE

PLEASE MAIL TO:

CUSTOMATIC Adjustable Bedz®

Customer Care Center

PO. BOX 10909

Riviera Beach, FL 33419 USA

Name

Phone

Address

City

State Zip

Store where purchased

Bed Serial No.

Invoice No.

No reimbursement will be made to the purchaser for inconvenience, removal, installation, setup time, lack of use, shipping, or any other costs

or expenses not covered by this warranty. CUSTOMATIC ADJUSTABLE BEDZ® does not hold responsibility for in-home service on adjustable

beds. You must contact your dealer or party that sold the adjustable bed for any terms and conditions relating to their in-home service, should

any exist.

CUSTOMATIC ADJUSTABLE BEDZ®, AND THEIR PARENTS, SUBSIDIARIES, DIVISIONS, AFFILIATES OR AGENTS MAKE NO

OTHER WARRANTY WHATSOEVER, EXPRESS OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED BY NAME AND EXCLUDED FROM THIS AGREEMENT.

The above limitation or exclusion may not apply to every purchaser as some states disallow exclusions or limitations of incidental or consequential damages.

This warranty allows the purchaser specific legal rights. The purchaser may also have other rights, which can vary from state to state. This warranty is valid in the