DIAS DIAS-CL User manual

User’s Manual
DIAS-CL Current Lockout System
Dias Geophysical Limited
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 2131 Airport Drive, Saskatoon, SK. , Canada. Printed in Canada.
2131 Airport Drive,
Saskatoon, SK,
S7L 7E1 Canada
Phone: [phone]
[email protected]
Adding value by delivering useful
knowledge through the innovation,
intellect and commitment of our team
DIAS-CL Current Lockout System USER’s MANUAL

DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 54 Alona Avenue, Cambridge, ON, Canada. Printed in Canada.
User’s Manual
Table of Contents
Limited Warranty, Limitations of Liability and Restrictions.......................................................................... 2
1.0 Introduction ............................................................................................................................................ 3
1.1 Unpacking Your System .......................................................................................................................... 3
1.2 General Description ................................................................................................................................ 3
1.3 Interface and Indicators.......................................................................................................................... 4
1.4 Field Procedures...................................................................................................................................... 5
1.5 Support.................................................................................................................................................... 7
Limited Warranty, Limitations of Liability and Restrictions
Dias Geophysical Limited hereinafter referred to as Dias, warrants that, for a period of 12
months from the delivery date to the original purchaser, Dias’ products will be free from defects
in materials and workmanship. EXCEPT FOR THE FOREGOING LIMITED WARRANTY, DIAS
DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Dias’ obligation is limited
to repairing or replacing parts or equipment which are returned to DIAS, transportation and
insurance pre-paid, without alteration or further damage, and which in Dias’ judgment, were
defective or became defective during normal use.
Dias ASSUMES NO LIABILITY FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR INJURIES CAUSED BY PROPER OR IMPROPER
OPERATION OF ITS EQUIPMENT, WHETHER OR NOT DEFECTIVE.
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 2131 Airport Drive, Saskatoon, SK. , Canada. Printed in Canada.

DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 54 Alona Avenue, Cambridge, ON, Canada. Printed in Canada.
1.0 Introduction
This manual is designed to provide instruction for the use and maintenance of the DIAS-CL
current lockout system. The DIAS-CL system is designed to be integrated with the DIAS-32 DCRC
(Direct Current Resistivity and Chargeability) system. The DIAS-CL system is intended to
augment, and integrate with, a well-designed set of field safety practices and procedures for
operation of electrical surveys. This manual is intended as both a reference and a teaching tool
and it is recommended that you read the entire document. If you experience operational problems
with your system, please call technical support at [phone].
1.1 Unpacking Your System
Thank you for purchasing a DIAS-CL system. A packing list is included with your shipment that
identifies all of the items that are in your order. You should check your shipment against the
packing list upon receipt of your shipment. If you find that an item is missing or was damaged
during the shipment, please call Dias immediately so that we can correct the problem. Following
is a list of items that are included with your shipment:
DIAS-CL current lockout units complete with internal battery
Lanyards for each DIAS-CL handheld
DIAS-CM-L current monitor equipped with DIAS-CL lockout technology
1.2 General Description
The DIAS-CL is a lightweight, portable technology that is designed to mitigate the risk of
electrocution from the high voltage wires and electrical equipment during the course of
geophysical surveying. Many ground geophysical surveys involve the transmission of current at
high voltage through wires that extend through the survey area, and through ground electrodes.
Direct current resistivity and chargeability (DCRC) surveys often involve the laying of extensive
amounts of conductive wire through the survey area. Current is transmitted through this wire
repeatedly through a production survey day, and between these transmission sessions, a portion
of the wire is moved by the survey crew members. Because of the large areas occupied by this
type of survey (>10 km in most cases), it is a challenge to mitigate the risk of electrocution,
particularly where traditional modes of communication fail.
The DIAS-CL system comprises a network of personal (handheld) devices that provide each crew
member who has one of the devices with overriding control over the electrical connection between
the transmitter and the current transmission wire. Status information for each crew member is
entered in their handheld and transmitted through the DIAS-32 mesh network to the DIAS-CM-L
current monitor and to the other crew members. For the DIAS-CL system to function as intended,
a DIAS-CM-L current monitor and a DIAS-32 system are required. The DIAS-CM-L device is
normally installed near the transmitter operator along the current transmission wire, and is
required to effect the override functionality of the DIAS-CL system through the integrated HV
relay, mesh network module, and controller. The DIAS-32 system is required for transmission of
the status information from each of the DIAS-CL devices to the DIAS-CM-L device. This
transmission is carried through the DIAS-32 mesh network system.
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 2131 Airport Drive, Saskatoon, SK. , Canada. Printed in Canada.

DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 2131 Airport Drive, Saskatoon, SK. , Canada. Printed in Canada.
DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 54 Alona Avenue, Cambridge, ON, Canada. Printed in Canada.
We highly recommend that the DIAS-CL technology be integrated into a field safety system that
addresses all aspects of the dangers of working with electrical equipment. The DIAS-CL
technology is designed to be nested with a standard ‘power ON –power OFF’ protocol using
conventional radio communication. In this way, the DIAS-CL system provides an added layer of
protection for the crew against electrocution, and there will be less risk of injury as crews transition
from the old transmitter protocols to the new system involving the DIAS-CL technology.
1.3 Interface and Indicators
DIAS-CL Controller
The DIAS-CL controller is a small, rugged, self-contained device that can be easily and quickly
deployed with minimal training. The external features of the DIAS-CL controller are shown in the
following image of the top surface of the handheld.
Figure 1: DIAS-CL interface layout.
Status Screen: Screen to display the status of the system.
System Status –the status of all units is given on the left hand side –up to 10
units can be displayed. The status of each is indicated as follows:
S –safe –indicates that the user is safe to be working with the wires
C –clear –indicates that the user is clear of the wires and current
transmission can proceed
O –offline –indicates that the user is offline, and may not be clear –
this status may be due to a power off condition, lack of network access, or
an unserviceable device
Tx –transmit - indicates that the current operator has authorised current
transmission and the user must assume that current is being transmitted
ID –supplies the mesh network ID for the device
Unit status –displays the status of the unit using the same nomenclature as given
above (S, C, O, Tx).
Current –displays the average on-time current in Amperes as recorded at the
DIAS-CL-L unit.
Four buttons in the lower portion of the device provide the following functionality:
Power:Power on/off button. Depress to power on. Depress and hold to power off.
Safe: To be depressed when the user is about to approach the transmitter wire. It should
be depressed when the user is still more than 3 m (5 m in some jurisdictions) from the
transmitter wire, and the transmitter current is already off. In rare circumstances, this
button can be depressed to effect shut-off of the transmitter current. The user should also
confirm that the transmitter current is zero prior to approaching the wire and doing any
work with the wire.
DIAS-CL Current Lockout System USER’s MANUAL

DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 2131 Airport Drive, Saskatoon, SK. , Canada. Printed in Canada.
DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 54 Alona Avenue, Cambridge, ON, Canada. Printed in Canada.
Clear:Depress when the user has completed all work with the transmitter wire and has
already moved greater than 3 m away from the wire (5 m in some jurisdictions). The
transmitter current can be turned on only when all units have their status set to clear.
Tx:Depress when all units have ‘Clear’ status. This button must be depressed to close
the relay in the DIAS-CM-L unit to allow for transmission of current through the current
trasnmission wires. Normally this button is depressed by either the transmitter operator or
the local current electrode operator.
DIAS-CL Receiver
The DIAS-CL receiver comprises a high-voltage relay, a mesh network card, a controller, a high-
gain antenna, and indicator lights. This receiver is currently integrated with the DIAS-CM current
monitor system. DIAS-CM units that have been retrofitted to contain the DIAS-CL receiver are
named DIAS-DM-L, with the ‘L’ extension on the name indicating that the unit has ‘Lockout’
functionality.
The only component that must be installed is the antenna, which must be screwed into the
antenna receptacle.
Two status LED lights indicate the status of the DIAS-CL receiver. If the red light is on, the status
is ‘Tx’, and if the green light is on, the status is ‘Safe’. These lights are provided for the benefit of
the current operator to indicate what state the DIAS-CL receiver is in.
1.4 Field Procedures
Following is a step-by-step description of the procedure for use of the DIAS-CL current lockout
technology.
Definition of Terms
Current Operator –crew member who will carry current wire, lay wire, embed current
electrodes in the earth, and make connections between current transmission wire and
electrodes.
Transmitter Operator –crew member in charge of operating the current transmitter.
Receiver Operator –crew member in charge of operating the DIAS-32 receivers.
DIAS-CL Receiver –Device for disengaging the path of electricity from the Current
Operator. This will normally be the DIAS-CM-L unit, which embodies both the DIAS-CM
current monitor and DIAS-CL receiver functionality.
DIAS-CL Controller –Handheld device for remotely controlling the DIAS-CL Receiver.
Pre-survey Preparation
Prior to mobilization to the survey site, determine the number of DIAS-CL units that will be
required for the survey. We recommend 2 to 3 spares for each survey.
Test the functionality of the DIAS-CM-L and DIAS-CL controllers.
Pre-operational Checks
Ensure that the DIAS-CM-L current monitor and all DIAS-CL controllers are checked for
battery performance on a daily basis to verify that the system is functioning properly for
the intended protection of crew and equipment. This is also important because controllers

DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 2131 Airport Drive, Saskatoon, SK. , Canada. Printed in Canada.
DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 54 Alona Avenue, Cambridge, ON, Canada. Printed in Canada.
that become unserviceable during the course of surveys can have significant production
consequences.
Ensure that each crew member that will be working with the current transmission lines or
that will be exposed to the current transmission wires is assigned a DIAS-CL controller.
Job Steps
IMPORTANT: Each step much be satisfied before proceeding to the next step of the procedure
Note: Clear communications must be maintained at all times between all members of the survey
crew to ensure all crew members clearly understand when power is ON and when power is OFF.
1. Initialization Procedure –each DIAS-CL controller that will be used for the survey
must be paired with the DIAS-CL receiver prior to surveying. This handshake
process can be carried out at any location within the network, but is perhaps best
done at the DIAS-CL receiver location. With both the receiver and the controller
powered on, press and hold the 'SAFE' button on the controller, then press ‘select’
on the receiver. A successful handshake will be indicated on the left hand side of
the controller, at which point the 'SAFE' button on the controller can be released.
2. Each crew member must ensure they are at least 3 meters (5 m in some
jurisdictions) from any potentially high voltage source. Once this condition is met,
each crew member is to push 'CLEAR' on the DIAS-CL controller. The status of
each crew member can be confirmed by all other crew members by viewing the
left side of the screen on the controller.
3. The current operator confirms that all crew members have a ‘CLEAR’ status.
4. The current operator pushes 'TX' and confirms the system is in the 'TRANSMIT'
state
5. The current operator radios “Power ON, Power ON”
6. The transmitter operator radios “Turning Power ON”, waits 5 seconds and turns on
the transmitter then radios “The Transmitter is ON, The Transmitter is ON”. Each
DIAS-CL controller will begin to display the average on-time amplitude of the
current waveform.
7. The current operator verifies power is on by viewing the cycling red light display
from a 3 meter distance or more on the DIAS-CM-L receiver.
8. When the receiver operator confirms that the IP/Resistivity measurements are
completed, the receiver operator radios “Power OFF, Power OFF”.
9. The transmitter operator turns off the transmitter then radios “Transmitter is OFF,
Transmitter is OFF”
10. The current operator pushes “SAFE” on the DIAS-CL controller before handling
any equipment used for the purpose of transmitting electricity.
11. Any crew member who needs to approach within 3 meters (5 m in some
jurisdictions) of a potentially high voltage source must push “SAFE” on their lockout
controller and verify the system is in the “SAFE” state before approaching the
potential high voltage source.
The above steps described in 2 through 11 are repeated for each transmit sequence.
The information in this procedure does not take precedence over legislation regarding the use of
electrical systems in the jurisdiction(s) in which the survey is taking place.

DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL Current Lockout System USER’s MANUAL
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 54 Alona Avenue, Cambridge, ON, Canada. Printed in Canada.
1.5 Support
Dias Geophysical provides full support for the DIAS-CL technology. Technical support is available
by calling [phone] and asking for Dias Technical Support Services. Unserviceable units
can be packed and shipped to the following address:
Dias Geophysical Limited
147 Robin Crescent
Saskatoon, Saskatchewan
S7L 6M3 Canada
Please visit our website at www.diasgeo.com for further contact information.
Dias Geophysical
2131 Airport Drive,
Saskatoon, SK,
S7L 7E1 Canada
DIAS-CL v.201412. All rights reserved including the right of reproduction in whole or in part in any form.
Dias Geophysical Limited, 2131 Airport Drive, Saskatoon, SK. , Canada. Printed in Canada.