Digi ConnectPort X2e ZB User manual

Quick Start Guide
ConnectPort X2e ZB
Power Supply
Ethernet Cable
ConnectPort X2e ZB
1 VerifyContents
2 WriteDowntheSerialNumber
®
Model: ConnectPort X2e ZB
Part Number: 50X2E-Z1C-001-01
Serial Number: 00409D50E9BB
Model: ConnectPort X2e ZB
Part Number: 50X2E-Z1C-001-01
Serial Number: 00409D 50E9BB
Write down the following located on the back of the
ConnectPort X2e ZB :
NOTE: The Serial Number is
also the Ethernet MAC
address.
Wi-Fi
Serial Number: ________________________________
(1P):90001296-88 B
3 ConnectHardware
Power XBee
Network
Button
aConnect the power supply.
bStartup Sequence -
After plugging in the device, the
Power LED will turn solid green, and the Network LED
will gradually turn solid green if it can connect to iDigi.
NOTE: This product requires a DHCP server to
assign its IP address. If you do not have a DHCP
server, see the
ConnectPort X2e ZB User’s Guide .
b
a
4 CongureYourDeviceUsingtheWi-Fiinterface
c
Enable Access Point mode on your device by pressing
the button.
NOTE:
If the ConnectPort X2e ZB has already been congured
to connect to an access point, it will need to be set back
to factory defaults to use the following procedure.
See the troubleshooting section below to return the
gateway to its initial state.
Congure the Wi-Fi interface of your laptop to
connect to the ConnectPort X2e ZB gateway’s access
point. The name (SSID) of the access point will be
cpx2e-zb-xxxxxxxxxx, where xxxxxxxxxxxx is the
serial number of the gateway.
a
b
a
b
c
cGo to your web browser, and enter the URL of the
ConnectPort X2e ZB gateway: http://192.168.100.1
Navigate to Configuration > Wireless Wizard.
Follow the steps in the wizard to congure your device.
eOnce the conguration is complete, your device will
reboot and connect to your home access point and
then attempt to connect to iDigi. You can track its
progress by observing the Network LED behavior.
It may take up to 5 minutes for the gateway to
connect to iDigi. After your gateway is connected to
iDigi, the network LED will be solid green.
d
d

© 2012 Digi International, Inc.
Digi, Digi International, Inc., ConnectPort, iDigi, and the Digi and iDigi logos are trademarks or registered trademarks of Digi International, Inc., in the United States and other countries worldwide. All other trademarks are the property of their respective owners.
Network LED
Button - Holding the button for ten seconds returns the device to factory defaults.
Need Help? Call 1-877-693-7849 or visit www.digi.com/support.
6 Troubleshooting
Power LED
For more information about this product, browse to www.digi.com/X2EZB
5 OnlineInstallation
Browse to www.digi.com/X2EZB and follow the instructions to download the Digi ESP ™ for Python
development environment and the ConnectPort X2e ZB User’s Guide.
a
7 RegulatoryInformation
http://ftp1.digi.com/support/documentation/x2e_wifi_reg.htm
For ConnectPort X2e ZB Wi-Fi regulatory information and certications, please refer to the document at the following URL:
Description
Status
Blinking yellow (slow) Operating system is running, but no Wi-Fi link is established.
OFF
Blinking yellow (fast)
Wi-Fi link is established, but no IP address is assigned to the gateway.
Solid yellow An IP address has been assigned to the gateway.
Blinking green (slow) Gateway is attempting a connection to an iDigi server.
Blinking green (fast) iDigi server found and gateway is undergoing authentication.
Solid green Gateway is connected to the iDigi server.
Alternating between
yellow and green
The gateway cannot connect to iDigi. The two most common reasons for
this state are:
- The gateway cannot connect to a DNS server to resolve the iDigi server address.
- The gateway cannot connect to an NTP time server to get the correct time.
See the iDigi User’s Guide’s Troubleshooting section to resolve this state.
Gateway operating system is not yet running.
Description
Status
No power.
Solid green Device is powered. This state does not indicate that the device is fully operational.
The Network LED and its states convey such information.
OFF