Digi TransPort WR11 Operator's manual

A
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
DIGI TRANS PORT WR11
1
Verify the kit contents
Quick Start Guide
TransPort WR11
A
B
CD
Mounting tips
TransPort WR11
Antennas
If any item is missing or damaged, please contact your supplier. Also, make a record of any damage that may have occurred during
shipping and report it to the supplier.
Depending on model and configuration, the package will also contain additional cables/antennas as appropriate.
2Install SIM card(s)
f
Power Supply Power Supply Adapters (for non-U.S. models only)
Close the SIM door.
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
Insert SIM card(s) into SIM sockets as shown.
The Dual SIM feature on the Digi TransPort WR11 provides support for a primary and secondary mobile service provider. Refer to
the TransPort User Guide (which can be found at www.digi.com/support) for instructions on using the Dual SIM feature.
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
Position the Digi TransPort WR11 on a flat surface. Only use the unit indoors, as it is not designed for outdoor use. Place the unit
where it has adequate ventilation. Also, do not expose the unit to extremes of heat or cold, strong magnetic fields, or liquids.
B
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
SIM 2
SIM 1
Insert SIM card(s). If you are only using one
SIM card, make sure you use the SIM 1 slot.
C
LTE Models
Open the SIM door. Using your finger, slide the SIM door out
and lift up.
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
90001406-88 C

© 2014 Digi Internatonal Inc. Digi, Digi International Inc., and the Digi logo are trademarks or registered trademarks of Digi International Inc., in the United States and other countries worldwide.
To complete configuration of your device, refer to the Digi TransPort WR11 Installation Guide provided on the Digi support site
(www.digi.com/support).
3Connect the antennas and power supply
What’s next?
Note: International units come with interchangeable power supply adapters which can be used according to regional needs.
5
B
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
4 Configure the unit
Connect the plug end of the power supply to the 5 volt power
connector on the device, and plug the other end into a wall
outlet.
Connect to the Web Interface: Open a web browser (such as
Firefox, Internet Explorer, or Chrome) on your PC and navigate
to http://192.168.1.1. If successful, you will be prompted to
enter a username and password. The default username is
username, and the default password is password.
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
AB
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
Connect an Ethernet Cable: Connect one end of the cable to the Ethernet port
on the device and the other end to an Ethernet port on a PC. Ensure that the DHCP
client is enabled on the PC.
Note: The Ethernet cable required for the connection is customer supplied.
The cable is not included in the package.
A
Note: When the signal strength is less than -101, the Signal-Strength LED is off. Place the device in a location where it gets a better signal.
C
To verify that the device is connected to the cellular network, check to see that the service LED is blinking as shown in the table.
You will also see the mobile IP address on the home page.
Insert power supply end fully and
rotate clockwise to engage
and lock.
Verify your connection
After you have logged in, it is strongly recommended that
you immediately change the default username and password.
WWAN
PRI
WWAN
SEC
SERVICE SIGNAL POWER
D
IGI
T
RANS
P
ORT
WR11
To optimize antenna
performance, see the Digi
TransPort WR11
Installation Guide available
at: www.digi.com/support.
Configure the APN:
Most LTE Carriers: Browse to Configuration - Network >
Interfaces > Mobile. Select the SIM1 or SIM2 using the
drop-down box. Go to Mobile Settings, and enter the
APN name assigned to that SIM. Click the Apply button
to apply changes, then click the here link to save all
changes. Click the Save button.
Verizon LTE Carriers: APN configuration is not required
since settings from the SIM card are automatically used by
default. Go to step 5 to verify your connection.
Note that if you are using a custom SIM, you must
enter the APN name assigned to that SIM. Your cellular
carrier assigns the APN name. Verizon users do not require
APN.
Connect the primary and the secondary cellular antennas to the
respective connectors (SMA female) on the unit.