Digi TransPort WR44 v2 User manual

Test a WR44v2 Router
How to test a WR44v2 router step by step.
Technical Support
December 2018

Contents
1 Introduction .......................................................................................................................................... 3
1.1 Outline .......................................................................................................................................... 3
1.2 Assumptions................................................................................................................................. 3
1.3 Corrections................................................................................................................................... 3
1.4 Version.......................................................................................................................................... 3
2 Equipment Required ............................................................................................................................. 4
3 Set up the test equipment .................................................................................................................... 5
4 Perform Low Level Tests ....................................................................................................................... 7
5 Program the Flash ................................................................................................................................. 8
5.1 Using Flashwriter ......................................................................................................................... 8
5.2 Reviewing Flashwriter error messages......................................................................................17
6 Check LEDs ..........................................................................................................................................18
7 Check W-WAN connectivity ................................................................................................................19
7.1 Test SIM detection switch..........................................................................................................19
7.2 Test SIM 1....................................................................................................................................20
7.3 Test SIM 2....................................................................................................................................23
8 Check W-WAN Signal Strength ...........................................................................................................25
9 Check USB ports.................................................................................................................................. 26
10 Check ETH ports 1 to 3....................................................................................................................27
11 Check Serial ports............................................................................................................................ 28
12 Testing the xDSL..............................................................................................................................30

How to test an WR44V2 step by step.
Page | 3
1INTRODUCTION
1.1 Outline
This guide will enable a competent technician to test the hardware of a WR44V2 router.
If the tests in sections 4 –11 all complete without a problem then the router can be returned to
service. If not please follow the advice in the documentation below for the error message you receive.
The guide makes no assumption about the state of the flash; it will work even if the system flash is
completely blank.
1.2 Assumptions
This guide has been written for use by technically competent personnel with a good understanding of
the product.
This guide assumes that there are no daughter cards fitted to the WR44. (E.g. GPS, serial, PSTN, ISDN,
Telemetry etc). If a daughter card is fitted please request additional testing steps from
[e-mail].
This note applies only to a WR44V2
1.3 Corrections
Requests for corrections or amendments to this documentation are welcome and should be
addressed to: tech.suppor[email protected]
Requests for new quick notes can be sent to the same address.
1.4 Version
Version Number
Status
0.6
Draft
1.0
Completed 26/03/2015
1.1
Rebranding + screenshot update
1.2
Module list update

How to test an WR44V2 step by step.
Page | 4
2EQUIPMENT REQUIRED
1. A PC connected to the Internet running a Microsoft Windows TM operating system with a built
in serial comm. port. (USB to serial adaptors do not work well.)
2. A 9-way to 9-way “straight through” serial cable to connect the PC directly to the WR44v2.
3. An Ethernet switch/hub to connect the PC to the WR44v2 (usually your normal office Ethernet
switch/hub will be fine if there is a spare port and it is NOT running spanning tree.)
4. CAT 5 cables to connect the WR44v2 and PC to the Ethernet switch.
5. A pen or paper clip which can easily de-press the WR44v2’s reset button

How to test an WR44V2 step by step.
Page | 5
3SET UP THE TEST EQUIPMENT
Set up the test equipment as described below.
Connect LAN 0 of the WR44V2 to the switch/hub.
Connect “ASY 0” the WR44V2 to the PC’s serial port 0 ideally “COM 1”.
The Internet connection is optional and will be useful if help is required during this process
from Digi Technical Support.
Please note that the Ethernet switch/hub must not have the spanning tree protocol enabled.
It is possible to use another appropriately configured WR44V2 as a switch/hub.
It is essential that the PC’s Ethernet communication interface is configured correctly and has
an IP address. The best strategy is normally to connect both your PC and the WR44V2 to your
normal office LAN.
Locate a suitable implement to depress the reset button when required.
Next download the following file:
http://ftp1.digi.com/support/firmware/transport/utils/mvtest.zip
Extract the contents of the zip file to a folder in the root directory of the test PC.

How to test an WR44V2 step by step.
Page | 6
Download the latest WR44V2 Flashwriter zip file and extract the contents to a single folder on
your PC:
http://ftp1.digi.com/support/firmware/transport/flashwriter/XXXX/WR44v2/WR44V2-XXXX-
flashwriter.zip
Where XXXX is the current firmware version, for example: 5281.
Extract the content of the downloaded zip file to a directory on your computer, for example
c:\wr44v2\ :
Open the .ini file extracted and add the following text to the second line (be sure to include the
comma):
marvelboot,
Save the changes to the ini file.
Finally download and install the latest version of Flashwriter
http://ftp1.digi.com/support/firmware/FlashWriter.msi

How to test an WR44V2 step by step.
Page | 7
4PERFORM LOW LEVEL TESTS
Connect the serial port of the PC to the WR44V2 using the serial cable.
From the Windows command line run the mvtest program including as an argument the PC com port
number:
mvtest -p 1
(E.g. for COM port 1)
mvtest -p 2
(E.g. for COM port 2)
Then power up the WR44V2. This may take a little practise. (Note that with the WR44V2 there is no
need to hold in the reset button for this step.)
Check the output of the mvtest program. If the test passes then the following output will be seen:
If all test show “passed” the router can now be safely power cycled.
If the SDRAM or FLASH test shows “failed”then the product should be returned via RMA. When
requesting the RMA please include the appropriate fail reason:
mvtest fail: SDRAM
mvtest fail: FLASH

How to test an WR44V2 step by step.
Page | 8
5PROGRAM THE FLASH
Please note that the most likely reason for this step to fail is due to an issue or configuration problem
with the test equipment. For this reason please verify that the steps below can be performed on a
known working WR44V2 without issue.
5.1 Using Flashwriter
Launch Flashwriter from the start menu. Select the communications port number (PC comm. port
number) to which the WR44v2 is connected. (On most PC’s with a built in serial port, this will be “1”
OR “2”. Leave the other settings are their default values (TFTP and Event driven mode ONLY ticked):
If your PC has more than one network adapter, be sure to select the one that represents the
connection to LAN illustrated in section 0. If your PC only has a single network adapter this screen will
not appear:

How to test an WR44V2 step by step.
Page | 9
In the file dialogue, select the “ALL” file you extracted from the ZIP earlier:
And click “Open”.

How to test an WR44V2 step by step.
Page | 10
The following message will appear:
It is critical that the correct selection is made at this point.
Note 1: Since FlashWriter version 1.0.525 characters 6 and 7 are included in the W-WAN module name,
see above.
Note 2: characters 6 and 7 of the part number (SKU) on the approval label. In the example below these
are “U8”:

How to test an WR44V2 step by step.
Page | 11
Refer to the following table to determine which selection to make:
Characters 6 &
7
Flashwriter Selection
00
100 No module
G1
5 Cinterion/Siemens MC75i/TC63i/MC75/Triorail
E1
5 Cinterion/Siemens MC75i/TC63i/MC75/Triorail
H0
9 Option HSDPA/HSUPA modules
H1
9 Option HSDPA/HSUPA modules
H2
9 Option HSDPA/HSUPA modules
C0
10 CMotech CDMA module
C1
11 Sierra Wireless CDMA module
C2
11 Sierra Wireless CDMA module
C3
10 CMotech CDMA module
C4
10 CMotech CDMA module
C6
10 CMotech CDMA module
C7
10 CMotech CDMA module
U0
9 Option HSDPA/HSUPA modules
U1
9 Option HSDPA/HSUPA modules
U2
13 Ericsson F3507g/F3607gw/F3307/F5521gw HSDPA module
U3
7 Sierra Wireless 3G module
U4
13 Ericsson F3507g/F3607gw/F3307/F5521gw HSDPA module
U5
17 Gobi UMTS or 18 Gobi CDMA
U6
13 Ericsson F3507g/F3607gw/F3307/F5521gw HSDPA module
U7
13 Ericsson F3507g/F3607gw/F3307/F5521gw HSDPA module
U8
17 Gobi UMTS
U9
24 Telit 3G
L1
28 Huawei LTE
L2
23 Novatel LTE
L3
23 Novatel LTE
L4
26 Sierra Wireless 4G/LTE module
L5
26 Sierra Wireless 4G/LTE module
L6
29 Telit LTE Version 1
L7
29 Telit LTE Version 1
L8
29 Telit LTE Version 1
L9
26 Sierra Wireless 4G/LTE module
M2
31 Cellient LTE
M3
32 Telit LTE Version 2
M4
29 Telit LTE Version 1
M5
32 Telit LTE Version 2
M6
32 Telit LTE Version 2
M7
32 Telit LTE Version 2
M8
26 Sierra Wireless 4G/LTE module
M9
29 Telit LTE Version 1

How to test an WR44V2 step by step.
Page | 12
Once you click ok, the following message should appear:
Click “OK”, then plug in the power.
If you are successful then the following message will appear:

How to test an WR44V2 step by step.
Page | 13
This step will take some time –please be patient. Once complete the boot image will be loaded into
the flash:
Eventually you should be prompted to enter the 6 digit serial number. (Refer to the label under the
WR44V2 to find the correct serial number.)

How to test an WR44V2 step by step.
Page | 14
Click OK
Next enter the hardware revision:
Click OK
The .ALL file should start to load:

How to test an WR44V2 step by step.
Page | 15
After reboot, it should check the interface to the W-WAN module (if one is fitted):
After this and other tests, it should report “Device upgraded successfully”:
This means the WR44V2 has been successfully flashed and correct communication with the internal
radio module (if fitted) verified.

How to test an WR44V2 step by step.
Page | 16
At this stage the following hardware components (and more) have been successfully tested :
FLASH
SDRAM
SRAM
ETHERNET 0
Serial port 0
Interface to radio module (if fitted)

How to test an WR44V2 step by step.
Page | 17
5.2 Reviewing Flashwriter error messages
If during the previous session an error occurred, please check the table below for the recommended
course of action:
Error Message
Recommendation
Unable to establish contact with Marvel CPU,
please try again.
This should not occur if the mvtest program was successful so suggests user
error or bad PC serial port, please try this step again.
XModem TX failure on loading Marvel UART
boot file.
This could be an issue with the PC serial port, check again that this works on
a known good router, if it does and it still fails with this error on a bad router
then request an RMA with reason: XModem TX failure on loading Marvel
UART boot file
Unable to start TFTP
Check that the Ethernet cable is connected correctly and the LAN LED is on.
This error can often be “user error” or “network issues”. However if this error
is repeatable on the suspected bad router but does not occur on a known
good router then request an RMA with reason. “Flashwriter TFTP failed to
start”
Blue progress bar moves, but slowly and with
lots of re-tries and eventually fails.
This suggests a hardware problem or a network issue on your LAN. Check
again that this works on a known good router, if it does and it still fails with
this error on the suspected bad router then request an RMA with reason.
“Flashwriter TFTP failed to complete”
Unable to communicate with device after
reboot
Check to see if the router is continuously rebooting. Please contact Digi
technical support for help.
W-WAN module failed check - please check
you selected the correct module!
Be very careful to check that you are selecting the correct radio module
when you launch FlashWriter. This is the number one cause of this error! If
you are unsure of the type of radio module fitted open the case.
If you are sure you are selecting the correct radio module and if this error is
repeatable on the suspected bad router yet works fine on a known good
router, please request an RMA with reason: “Flashwriter radio check failed.”

How to test an WR44V2 step by step.
Page | 18
6CHECK LEDS
Connect all four Ethernet ports to a switch.
Access the CLI (Command Line Interface) –this can be achieved:
Through the serial port @115200 bps
Via a telnet or SSH connection
Via the “execute a command” page of the web user interface.
Issue the “flashleds” command and check that all LEDs are illuminated. If there is an LED fault please
request an RMA with code:
“x LED failure” where x is:
ON LED
LAN 0
LAN 1
LAN2
LAN3
WLAN
DSL
LINK
SIM
ACT
Signal I
Signal II
Signal III

How to test an WR44V2 step by step.
Page | 19
7CHECK W-WAN CONNECTIVITY
7.1 Test SIM detection switch
With the router powered off, insert a SIM card into BOTH SIM slots of the WR44V2 and open the CLI
interface.
Access to the CLI (Command Line Interface) –this can be achieved:
Through the serial port @115200 bps
Via a telnet or SSH connection
Via the “execute a command” page of the web user interface.
Issue the following command:
simconn ?
This command tells you which SIM slots are populated and also the SIM that is currently in use. The
value before the comma is SIM 1 and the value after the comma is SIM 2. 1000 means that the SIM is
present. 1001 means that the SIM is present and the active SIM. Here is a summary:
1 = SIM not present
1000 = SIM present
1001 = SIM present and connected
The output should be as follows:
simconn ?
simconn: 1001,1000
OK
Showing that SIM 1 is present and active and SIM 2 is present.
If the SIM cards are physically inserted but do not show as present please request an RMA with reason
“SIM DETECTION FAIL”

How to test an WR44V2 step by step.
Page | 20
7.2 Test SIM 1
Ensure that an antenna is connected and the router is located in an area with good signal strength.
Navigate to:
Configuration - Network > Interfaces > Advanced > PPP 1 > Mobile
Change W-WAN SIM: from “Any” to “SIM 1”
Click Apply.