Digital Projection E-Vision Laser 13000 WU Series Datasheet

Rev A June 2019
E-Vision Laser 13000 WU Series
High Brightness Digital Video Projector
INSTALLATION & QUICK START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REFERENCE GUIDE
119-946A

Digital Projection Ltd. E-Vision Laser 13000 WU Series About this document
About this document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this document
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are
closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely
followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior notice.
Updates may be available online. Please visit the Digital Projection website for all latest documents.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners. Digital Projection disclaims any proprietary interest in
trademarks and trade names other than its own.
Copyright © 2019Digital Projection Ltd. All rights reserved.
Rev A June 2019
page 2
Introduction
Notes

Laser information Digital Projection Ltd. E-Vision Laser 13000 WU Series
Laser information
3264655900
GB 7247.1-2012 / IEC/EN 60825-1:2007
PRODUIT LASER DE CLASSE 1
第一類雷射產品
IEC/EN 60825-1:2014
CLASS 1 LASER PRODUCT
一类激光产品
IEC/EN 60825-1:2014
Warning ! Do not look into the beam.
No direct eye exposure to the beam
is permitted.
RG3
Hazard Distance : 3.5m
警告 ！请勿直视镜头。
眼睛不要直接暴露于光辐射 。
RG3
危险距离：3.5米
Avertissement ! Ne Pas Regarder
Directement Dans Le Faisceau.
L’exposition Directe Des Yeux Au
Faisceau Est Interdite.
RG3
Distance À Risque : 3.5m
警告 ！ 請勿直視鏡頭。
眼睛不要直接暴露於光輻射。
RG3
危險距離：3.5公尺
激光辐射
避免眼睛受到直接照射
3R类激光产品 波长 : 450-460 nm (蓝)
最大脉冲能量: 0.45 mJ (蓝),
脉冲时间: 0.87 ms (蓝)
3R类激光产品 波长 : 636-646 nm (红)
最大脉冲能量: 0.72 mJ (红),
脉冲时间: 1.6 ms (红)
雷射輻射
避免眼睛受到直接照射
3R類雷射產品 波長: 450-460 nm (藍)
最大脈衝能量: 0.45 mJ (藍),
脈衝時間: 0.87 ms (藍)
3R類雷射產品 波長: 636-646 nm (紅)
最大脈衝能量: 0.72 mJ (紅),
脈衝時間: 1.6 ms (紅)
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Emitted Wavelength : 450-460 nm (Blue)
max pulse energy : 0.45 mJ (Blue)
Pulse duration : 0.87 ms (Blue)
Emitted Wavelength : 636-646 nm (Red)
max pulse energy : 0.72 mJ (Red)
Pulse duration : 1.6 ms (Red)
RAYONNEMENT LASER
EXPOSITION DIRECTE DANGEREUSE
POUR LES YEUX
APPAREIL À LASER DE CLASSE 3R
longueur d'onde : 450-460 nm (Bleu)
maximum énergie de impulsion : 0.45 mJ (Bleu)
durée de impulsion : 0.87 ms (Bleu)
longueur d'onde : 636-646 nm (Rouge)
maximum énergie de impulsion : 0.72 mJ (Rouge)
durée de impulsion : 1.6 ms (Rouge)
Complies with FDA performance standards for laser
products except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007
Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation
exposure.
警告 ！请勿直视镜头。
眼睛不要直接暴露于光辐射 。
RG3
危险距离：0-650厘米
警告 ！ 請勿直視鏡頭。
眼睛不要直接暴露於光輻射。
RG3
危險距離：0-650公分
Not for home use.
Optical radiation
DO NOT let a laser beam directly
enter the projector lens.
Caution - possibly hazardous optical radiation emitted from this product. Do not stare at operating light source. May be harmful to eyes. This
projector is tested according to IEC/EN62471-5:2015 (Photobiological safety of lamps and lamp systems – Part 5: Image projectors standard) and is
Risk Group 3 (high risk).
Introduction Rev A June 2019
page 3
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Light Hazard Warning
Light Hazard Warning
No direct exposure to the
beam is permitted, RG3
IEC 62471-5:2015.
Operators should control
access to the beam
within the hazard
distance or install the
projector at sufficient
height to prevent
exposures of spectators’
eyes within the hazard
distance.
Hazard Distance
The hazard distance is the distance measured from the
projection lens at which the intensity or energy per unit of
surface is lower than the applicable exposure limit on the
cornea or skin. If the person is within the hazard distance, the
beam is considered unsafe for exposure.
Light Hazard Distances
The hazard distance for this projector is 3.5 m.
Rev A June 2019
page 4
Introduction
Notes

Introduction Digital Projection Ltd. E-Vision Laser 13000 WU Series
Introduction
Congratulations on your purchase of this Digital Projection product. Your projector has the following key features:
lWUXGA projector.
lSupport for Frame Sequential and Dual Pipe 3D formats.
lHDBaseT® for transmission of uncompressed High Definition Video up to 100 m from the source.
l3G-SDI with loop-through.
lEdge Blend with black level correction.
lRed laser assist for enhanced color fidelity.
lBlanking control for custom input window sizing.
lCornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
lControl via LAN and RS232.
lMotorised lens mount.
lSeparate control of screen and source aspect ratio.
A serial number is located on the side of the projector. Record it here:
Introduction Rev A June 2019
page 5
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Contents
About this document 2
Symbols used in this document 2
Product revision 2
Legal notice 2
Laser information 3
Optical radiation 3
Light Hazard Warning 4
Light Hazard Distances 4
Introduction 5
Contents 6
What's in the box? 10
Connecting the power supply 11
Voltage selection 11
Projector overview 12
Control panel 13
Projector indicators 14
Remote control 15
Infrared reception 18
Positioning the screen and projector 19
Roll and pitch 20
Changing the lens 21
Inserting a new lens 21
Removing the lens 22
Operating the projector 23
Switching the projector on 23
Switching the projector off 23
Selecting an input signal 23
Selecting a test pattern 23
Adjusting the lens 24
Lens menu 24
Remote control 24
Adjusting the image 24
Orientation 24
Geometry 24
Picture 24
Signal inputs 26
Digital inputs and outputs 26
Analog inputs and outputs 26
EDID on the DisplayPort, HDMI, and HDbaseT inputs 27
Using DisplayPort/ HDMI/ HDBaseT switchers with the projector 27
3D connections 28
3D sources up to 60Hz requiring frame doubling and left/right
interleaving 29
Frame sequential 3D sources up to 120Hz 29
Dual Pipe 3D 29
3D Sync 30
Control connections 31
LAN connection examples 32
RS232 connection example 33
Using the menus 36
Opening the Menu 36
Opening a submenu 36
Rev A June 2019
page 6
Introduction
Notes
Contents

Contents Digital Projection Ltd. E-Vision Laser 13000 WU Series
Exiting menus and closing the OSD 37
Inside a menu 37
Accessing sub menus 38
Executing commands 38
Editing projector settings 39
Using a slider to set a value 39
Editing numeric values 40
Using the projector 41
Main menu 41
Lens menu 42
Lens control 42
Lens memory 43
Image menu 44
Position and phase 45
Noise reduction 46
Color menu 47
Color space 47
Color mode 48
ColorMax 48
Manual color matching 49
Color matching parameters explained 50
Color temperature 51
Gains and lifts 51
Geometry menu 52
Aspect ratio 52
Theaterscope setting 53
Digital zoom 54
Overscan 55
Blanking 56
Keystone 57
Keystone example 58
Keystone settings 59
4 corners 60
Top right corner example 61
Rotation 62
Rotation example 63
Pincushion / barrel 64
Pincushion/ Barrel example 64
Arc 65
Custom warp 66
Edge blend menu 67
Blend start 68
Blend width 69
Black level uplift 70
3D menu 71
3D types 72
Some 3D settings explained 73
Dark time 73
Eye swap 73
Sync offset 74
Laser menu 75
Setup menu 76
ColorMax 78
Measured data/ target data 78
Introduction Rev A June 2019
page 7
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Contents
Power on / off 79
Clock adjust 80
OSDsettings 80
Memory 81
Network menu 82
PIP menu 83
Information menu 84
Signal format 84
System status 85
Thermal status 85
Factory reset 86
Served web pages 87
Choosing a lens 94
Basic calculation 95
Basic calculation example 96
Full lens calculation 97
Introducing TRC 97
Calculating TRC 98
TRC table 98
Calculating the throw ratio with TRC 98
Full lens calculation example 99
Screen requirements 100
Fitting the image to the display 100
WUXGA images displayed full width 100
WUXGA images displayed with a height of 1200 pixels 100
WUXGA images displayed full height 101
Diagonal screen sizes 101
Positioning the image 102
Aspect ratios explained 104
Aspect ratios examples 104
Source: 4:3 104
Source: 16:9 105
Source: 16:10 (native) 105
Aspect ratio example: TheatreScope 106
Appendix A: supported signal input modes 107
2D formats 107
3D formats 109
SDI formats 111
Appendix B: wiring details 112
Signal inputs and outputs 112
HDMI 1 and 2 112
DisplayPort 113
3G-SDI in, 3G-SDI out 114
HDBaseT input 114
Control connections 115
LAN 115
RS232 115
IR input 115
Appendix C: glossary of terms 116
Rev A June 2019
page 8
Introduction
Notes

Rev A June 2019
E-Vision Laser13000 WU Series
High Brightness Digital Video Projector
INSTALLATION & QUICK START GUIDE
119-946A

Digital Projection Ltd. E-Vision Laser 13000 WU Series What's in the box?
What's in the box?
Make sure your box
contains everything listed.
If any pieces are missing,
contact your dealer.
Only one remote is
supplied with the
projector.
Save and store the
original box and packing
materials, in case you
ever need to ship your
projector.
The projector is shipped
without a lens.
Only the appropriate cable
for destination territory is
supplied with the projector
Projector
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
Remote Control
Batteries
Security Screw
Important Information Book HDMI Cable
Power Cable, UK Power Cable, Europe Power Cable, North America Power Cable, China
Rev A June 2019
page 10
Installation & Quick Start Guide
Notes

Connecting the power supply Digital Projection Ltd. E-Vision Laser 13000 WU Series
Connecting the power supply
Use only the power cable
provided.
Ensure that the power
outlet includes a ground
connection as this
equipment MUST be
earthed.
Handle the power cable
carefully and avoid sharp
bends. Do not use a
damaged power cable.
1
2
1. Adjust the VOLTAGE SELECT switch to the required voltage
1
2. Firmly push the mains connector into the socket
2
Voltage selection
The VOLTAGE SELECT switch must be set to match the power supply you are using:
Voltage of power supply used Position of VOLTAGE SELECT switch
AC100-130V outlet
AC200-240V (single phase) outlet
Installation & Quick Start Guide Rev A June 2019
page 11
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Projector overview
Projector overview
5
6
7
8
9
10
11
Rear View
12
Bottom View
1
2
4
3
Front View
1. Air inlet
2. Front infrared window
3. Lens mount
4. Air inlet
5. Rear infrared window
6. Air outlet
7. Connections panel
8. Control panel
9. Adjustable feet
10. Voltage selector
11. Mains socket and switch
12. Air inlets
Rev A June 2019
page 12
Installation & Quick Start Guide
Notes

Control panel Digital Projection Ltd. E-Vision Laser 13000 WU Series
Control panel
POWER
INPUT AUTO
SYNC ASPECT CENTER
LENS PIC MUTE
1
2
3
4
5
6
7 8 9 10 11 12
Control Panel
1. POWER
Switches the projector on and off (STANDBY).
2. INPUT
Switches to the next input source.
3. AUTO SYNC
Re-synchronises with the current input signal.
4. ASPECT
Changes the aspect ratio.
5. CENTER LENS
Centers the lens.
6. PIC MUTE Shows and hides the projected image. When
muted, the light source is completely switched off and
the screen is black.
7. MENU
Displays and exits the OSD.
8. Arrow buttons & ENTER
Navigation buttons used to highlight menu entries in the
OSD. Press ENTER to open or execute the highlighted
menu entry.
9. EXIT
Exits the current OSD page and enters the level above.
10. LENS SHIFT
Arrow buttons move the lens in the specified direction.
11. FOCUS
Plus and minus buttons move the focus in and out.
12. ZOOM
Plus and minus buttons zoom in and out.
Installation & Quick Start Guide Rev A June 2019
page 13
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Control panel
Projector indicators
POWERSTATUSLIGHTTEMP.
Indicators
TEMP. Off = no problem
Flashing red = temperature error
LIGHT Off = light is switched off
Flashing green = light is preparing to switch on
Flashing red (cycles of six flashes) = light module failure
On, red = light module has reached end of life
On, green = light is switched on
STATUS Off = no problem
Flashing red (continuously) = cover error
Flashing red (cycles of four flashes) = fan error
On, red = system error
POWER Off = the projector is switched off
Flashing green = the projector is warming up
Flashing amber = the projector is cooling down
On, red = STANDBY mode
On, green = the projector is switched on
Rev A June 2019
page 14
Installation & Quick Start Guide
Notes

Remote control Digital Projection Ltd. E-Vision Laser 13000 WU Series
Remote control
8
6
5
4
3
2
1
7
9
10
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
Remote Control
1. Power ON / OFF
Turns power on and off.
2. Pic Mute OPEN / CLOSE
Shows and hides the projected image.
When OFF, the light source is completely switched off and the screen is black.
3. OSD ON / OFF
Enable and disable screen timeout messages and control whether to show the OSD during
projection.
4. MENU
Access the OSD. If the OSD is open, press this button to go back to the previous menu.
5. Navigation (arrows and OK)
Navigate through the menus with the arrows, confirm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens.
See 11 below. In lens adjustment modes, or when the OSD is not showing, the OK button
switches between modes: Shift Adjustment and Zoom / Focus Adjustment.
6. EXIT
Go up one level in the OSD. When the top level is reached, press to close the OSD.
7. FREEZE
Freeze the current frame.
8. DEFAULT
When editing a parameter, press this button to restore the default value.
9. INFO
Access information about the projector.
10. RE-SYNC
Re-synchronise with the current input signal
Installation & Quick Start Guide Rev A June 2019
page 15
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Remote control
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
11
13
12
14
15
16
Remote Control
11. LENS adjustment
lFOCUS IN / OUT: adjust focus.
lSHIFT: press and hold this button, then use the Navigation arrow buttons to move the
lens.
lZOOM IN / OUT: adjust zoom.
12. USER PRESET A, B, C, D
Load user presets.
13. ALT
Press and hold this button to access alternative functions for all buttons with a green label.
This projector does not
use the following options
on the remote: DVI, VGA,
COMP 1 and COMP 2.
14. DVI / GAMMA / numeric input 3
There is no DVI input on this projector.
Use with ALT to switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
15. HDMI 2 / CON / numeric input 2
Select the HDMI 2 input.
Use with ALT to bring up the Contrast control, then adjust the value with the LEFT and
RIGHT arrow buttons.
16. HDMI 1 / BRI / numeric input 1
Select the HDMI 1 input.
Use with ALT to bring up the Brightness control, then adjust the value with the LEFT and
RIGHT arrow buttons.
Rev A June 2019
page 16
Installation & Quick Start Guide
Notes

Remote control Digital Projection Ltd. E-Vision Laser 13000 WU Series
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
17
23
19
21
22
24
18
20
Remote Control
17. DISPLAYPORT 1 / R / numeric input 4
Select DisplayPort 1 input.
18. HD-T / G / numeric input 5
Select the HDBaseT input.
This projector does not
use the following options
on the remote: DVI, VGA,
COMP 1 and COMP 2.
19. VGA / 3D / numeric input 7
There is no VGA input on this projector.
Use with ALT to toggle the 3D Format setting between Off and Auto.
20. COMP1 / EYE / numeric input 8
There is no Component 1 input on this projector.
Use with ALT to switch between left and right eye 3D dominance.
21. ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
lTo assign an IR remote address:
1. Press and hold this button until the red indicator starts flashing.
2. Release this button and while the red indicator is still flashing, enter a two-
digit address using the numeric input buttons. The indicator will flash three
times quickly to confirm the change.
lTo unassign an address and return to the default address 00:
1. Press and hold ALT and this button simultaneously until the red indicator
flashes to confirm the change.
22. 3GSDI / B / numeric input 6
Select the 3G-SDI input.
23. TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern: White, Black, Red, Green,
Blue, Checkerboard, Crosshatch, V Burst, H Burst, Color Bar, Screen Layout, Off..
When PIP mode is on, use this button with ALT to swap the main and sub images.
24. COMP2 / PIP / numeric input 9
There is no Component 2 input on this projector.
Use with ALT to switch on Picture In Picture (PIP) mode.
Installation & Quick Start Guide Rev A June 2019
page 17
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Remote control
Infrared reception
40˚
40˚
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance
when trying to control the projector.
Rev A June 2019
page 18
Installation & Quick Start Guide
Notes

Positioning the screen and projector Digital Projection Ltd. E-Vision Laser 13000 WU Series
Positioning the screen and projector
1
1
1
1
2
2
2
2
2
2
Always allow the
projector to cool for 5
minutes before
disconnecting the power
or moving the projector.
Ensure that there is at
least 50 cm (19.7 in) of
space between the
ventilation outlets and
any wall, and 30 cm (11.8
in) on all other sides.
Do not use the threaded
holes for the adjustable
feet to hang or mount the
projector.
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to
fill the screen. Set the adjustable feet so that the projector is level, and perpendicular to the
screen.
The drawing shows the positions of the feet for table mounting, and the fixing holes for ceiling
mounting.
1. Four adjustable feet
2. Six M4 holes for ceiling mount The screws should not penetrate more than 15 mm into the
body of the projector.
Installation & Quick Start Guide Rev A June 2019
page 19
Notes

Digital Projection Ltd. E-Vision Laser 13000 WU Series Positioning the screen and projector
Roll and pitch
The projector can be operated in numerous positions.
360˚
2
Pitch
30˚
330˚
2
1
Roll
In portrait mode, it is
recommended to position the
projector with inputs facing
upward, as shown in the diagram.
1. Recommended positions:
inputs side up
2. Also possible.
Rev A June 2019
page 20
Installation & Quick Start Guide
Notes