Digital Projection Titan Super Quad User manual

Rev F November 2012
USER GUIDES
INSTALLATION AND QUICK-START GUIDE
CONNECTION GUIDE
OPERATING GUIDE
REFERENCE GUIDE
Titan 800 Series
High Brightness Digital Video Projector
Titan Super Quad Series
Titan Quad 2000 Series
Titan Quad Series
112-671F

Digital Projection Titan Quad & Titan 800 Series
Rev F November 2012
About These Guides
Please keep these Guides handy for future reference.
A serial number is located on the back of the projector. Record it here:
Symbols used in these Guides
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2012 Digital Projection Ltd. All rights reserved.
Notes

Rev F November 2012
INSTALLATION AND QUICK-START GUIDE
Titan 800 Series
High Brightness Digital Video Projector
Titan Super Quad Series
Titan Quad 2000 Series
Titan Quad Series

Digital Projection Titan Quad, & Titan 800 Series CONTENTS Installation and Quick-Start Guide
Rev F November 2012
CONTENTS
What’s In The Box? ..............................................................................Inst 1
Getting to Know the Projector.....................................................Inst 2
Front and rear views ..............................................................................Inst 2
Remote control.......................................................................................Inst 2
Control panel indicators........................................................................Inst 3
Connection panel indicators.................................................................Inst 3
Positioning The Screen And Projector...................................Inst 4
Chassis adjustment ...............................................................................Inst 4
Fitting and adjusting the optional Rigging Frame ..............................Inst 4
Fitting The Lens .....................................................................................Inst 5
Operating The Projector ..................................................................Inst 6
Switching the projector on....................................................................Inst 6
Selecting an input signal or test pattern..............................................Inst 6
Input signal.....................................................................................Inst 6
Test pattern ....................................................................................Inst 6
Adjusting the lens ..................................................................................Inst 7
Zoom..............................................................................................Inst 7
Focus .............................................................................................Inst 7
Shift................................................................................................Inst 7
Adjusting the image...............................................................................Inst 7
Orientation and On-Screen Display settings..................................Inst 7
Keystone ........................................................................................Inst 7
Picture............................................................................................Inst 7
Switching the projector off....................................................................Inst 8

Digital Projection Titan Quad, & Titan 800 Series WHAT’S IN THE BOX? Installation and Quick-Start Guide
Inst 1
Rev F November 2012
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
Remote control
(105-023)
4x AAA batteries
Power cable, United Kingdom
(102-180 for Titan 800, 112-000
for Quad)
User Guides on CD
(112-659)
Important Information (112-658)
Power cable, Europe
(102-163 for Titan 800, 112-001 for Quad)
Power cable, North America
(102-165 for Titan 800, 112-002 for Quad)
Projector
Remote cable
(102-162)

Digital Projection Titan Quad, & Titan 800 Series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Inst 2
Rev F November 2012
Getting to Know the Projector
Front and rear views Remote control
Transmit
indicator
40°
40°
Infra-red
reception
Notes
The projector uses the standard
Digital Projection infra-red remote
control.
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.
The Side Connection Panel is
available on 3D models only.
Lens
Control
panel Side
Connection
panel
Front
infra-red
window
Mains
input
Rear
infra-red
window
(on
connection
panel)
Air lters
(behind panel)
Adjustable
feet
Air
inlets
Air
outlets
Remote
control
backlight
On/Off
Rear
Connection
panel

Digital Projection Titan Quad, & Titan 800 Series GETTING TO KNOW THE PROJECTOR Installation and Quick-Start Guide
Inst 3
Rev F November 2012
Control panel indicators
The indicators on the control panel are as follows:
Power off = NO POWER
green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Connection panel indicators
The indicators on the rear connection panel are as follows:
All on = Power-On Self Test
Lamps 1-4 off = OFF
green = ON (100%) amber = (80 - 99%)
ashing green = WARM-UP ashing amber = COOL-DOWN
red (projector in standby) = Lamp Comms Error (call service)
red (projector on) = Ballast Comms Error (call service)
ashing red (projector in standby) = Lamp Error on previous operation
ashing red (projector on) = Lamp / Interlock Error
Error ashing = Fan / System Error steady = Voltage Error
IR blue ash = Remote control command received
Inputs The indicators next to the input connectors on both panels are as follows:
off = not selected
green = input selected, signal detected, and in range
ashing green = input selected, but signal not detected or out of range
Power Shutter
Notes
Only the controls shown highlighted
are used on this projector.
For full details of how to use the
controls and the menu system, see
the Operating Guide.
For more information about
the connection panels, see the
Connection Guide.
Control Panel
Error
Lamps
3 4
1 2
Side Connection Panel
IR
Rear Connection Panel

Digital Projection Titan Quad, & Titan 800 Series POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide
Inst 4
Rev F November 2012
Positioning The Screen And Projector
• Install the screen, ensuring that it is in the best position for viewing by your audience.
• Position the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen.
Chassis adjustment
• If the projector is to be operated from a at surface such as a projector table, then adjustment of projector level should be made by turning
the four feet under the chassis. Set the adjustable feet so that the projector is level, and perpendicular to the screen.
Fitting and adjusting the optional Rigging Frame
• Remove the four adjustable feet.
• Secure the rigging frame to the projector, as shown below, making sure that the cable
attachments are at the top. Three screws secure each of the adjuster brackets to a corner
handle.
• To adjust the pitch, turn either the front pair or the rear pair of vertical adjusters, taking
care to turn both adjusters by the same amount.
• To adjust the roll, turn either the left pair or the right pair of vertical adjusters, taking care
to turn both adjusters by the same amount.
• To adjust the yaw, turn the single horizontal adjuster at the front.
Fixing
screws
Yaw
Horizontal
adjuster
Vertical
adjusters
Frame
couplings
Pitch Roll
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least
30cm (12in) of space between the
ventilation outlets and any wall,
and 10cm (4in) on all other sides.
Do not stack more than 3
projectors.
Do not place heavy objects on top
of the projector chassis. Only the
chassis corners and the rigging
frame are capable of withstanding
the weight of another projector.
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
Backup safety chains or wires
should always be used with
ceiling mount installations.
Do not tilt the projector more
than ±12° in either direction, in
desktop or ceiling mode, when in
use, as this may cause serious
lamp failure, damage the lamp
module and cause extra cost on
replacement.
±12°±12°
±12°±12° Ceiling
Desktop

Digital Projection Titan Quad, & Titan 800 Series FITTING THE LENS Installation and Quick-Start Guide
Inst 5
Rev F November 2012
Fitting The Lens
• Turn the lens release lever clockwise so
that it is pointing upwards, to open the
lock fully.
• Remove the rear lens cap from the lens.
• Insert the lens into the lens aperture,
making sure that the plug on the zoom
drive mechanism lines up with the socket
on the front of the projector, then push
the lens in rmly as far as it will go.
Lens
release
lever
Notes
Always allow the lamp to cool for
5 minutes before:
- disconnecting the power
- moving the projector
The lens release lever should
always be set to the locked
position to prevent the lens from
falling out.
Do not place the projector with its
front panel down on a surface, as
this may damage the lens or the
lens release lever.
• Turn the lens release lever anti-clockwise
to the mid-position.
• The lens can now be pushed in further.
Push the lens in rmly as far as it will go.
• Turn the lens release lever fully
anti-clockwise so that it is pointing
downwards, to close the lock fully.

Digital Projection Titan Quad, & Titan 800 Series OPERATING THE PROJECTOR Installation and Quick-Start Guide
Inst 6
Rev F November 2012
Operating The Projector
Switching the projector on
• Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector.
• Wait until the self-test has completed and the standby indicator on the projector control panel shows amber. The lamp will be off and the
projector will be in STANDBY mode.
• Press on the remote control or the control panel and hold for 3 seconds, to switch the projector ON. The power indicator on the
control panel will show green, the lamp will light and the shutter will open.
Selecting an input signal or test pattern
Input signal
• Connect an image source to the projector. The signal should be automatically detected by the projector,
and should be displayed within two or three seconds.
If more than one signal is connected, then select the image you want to display:
• Press one of the Input buttons, to on the remote control, or
• Open the On-screen display (OSD) by pressing .
• Select an input signal from the Input Selection menu, using the and buttons.
Test pattern
If you have no image source connected to the projector, then you can display a test pattern instead:
• Open the OSD by pressing .
• Select Test Pattern from the Input Selection menu, using the and buttons.
• Select a pattern from the Test Pattern menu, using the and buttons.
• Close the OSD by pressing again.
Notes
For full details of how to use the
controls and the menu system, see
the Operating Guide.