Digital Projection MERCURY 5000HD User manual

MERCURY 5000HD
Super High Brightness Digital Video Projector
16:9 widescreen display
This information booklet contains the following:
Declaration of Conformity
Important Information
What’s in the Box?
Optional Lens Installation
Replacing the Lamp
Replacing or Cleaning the Filter
Cleaning the Cabinet and the Lens
Troubleshooting
Specifications
Full information about operating, connecting and setting up the
projector can be found in the User Manual
103 511 A

Digital Projection MERCURY 5000HD
Declaration of Conformity
Directives covered by this Declaration
89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC and 93/68/EEC.
73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.
Products covered by this Directive
Large Screen Projector type MERCURY 5000HD
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU directives, and the
manufacturer has applied the following standards.
EN 50081-1:1992 - EMC Generic Emission Standard for Residential, Commercial and Light Industrial Equipment.
EN 50082-1:1992 - EMC Generic Immunity Standard for Residential, Commercial and Light Industrial Equipment.
EN 55022:1995 - Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology
Equipment.
EN 60950:1992 - Specification for Safety of Information Technology Equipment, including Electrical Business equipment.
The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage
directive has been compiled by the signatory below and is available for inspection by the relevant enforcement
authorities. The CE mark was first applied in 2004.
Signed:
Authority: D.J. Quinn, Director - Product Development
Date: 23 April 2004
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which
must be observed when these products are taken into service to maintain compliance with the above directives.
Details of these special measures are available on request, and are also contained in the product manuals.

Digital Projection MERCURY 5000HD
Important Information
Precautions
Please read this manual carefully before using your Digital
Projection MERCURY 5000HD Projector and keep the manual
handy for future reference.
Your serial number is located on the side of your projector.
Record it here:
CAUTION
To turn off main power, be sure to remove the
plug from power outlet.
The power outlet socket should be installed as
near to the equipment as possible, and should
be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE
CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED Digital
Projection SERVICE PERSONNEL.
This symbol warns the user that uninsulated
voltage within the unit may be sufficient to
cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any
part inside of the unit.
This symbol alerts the user that important
information concerning the operation and
maintenance of this unit has been provided. The
information should be read carefully to avoid
problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITHAN
EXTENSION CORD OR IN AN OUTLET UNLESS ALLTHREE
PRONGS CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE
COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY
QUALIFIED Digital Projection SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
3. GSGV Acoustic Noise Information Ordinance:
The sound pressure level is less than 70 dB (A) according to
ISO 3744 or ISO 7779.
In UK, a BS approved power cable with moulded plug has a
Black (five Amps) fuse installed for use with this equipment. If
a power cable is not supplied with this equipment please
contact your supplier.
• IBM is a registered trademark of International Business Machines
Corporation.
• Macintosh and PowerBook are registered trademarks of Apple
Computer, Inc.
• Other product and company names mentioned in this user's manual
may be the trademarks of their respective holders.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified
by Digital Projection in this manual. Failure to comply with this
government regulation could void your right to operate this
equipment.
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
Important Safeguards
These safety instructions are to ensure the long life of your
projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away
from dust and moisture. Do not tilt the projector more than
±12° from side to side, as this will reduce lamp life. The
projector may be tilted forwards or backwards as necessary.
3. Do not place your projector in direct sunlight, near heaters or
heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm
internal components.
5. Handle your projector carefully. Do not hold the lens hood
and the terminal covers. Dropping or jarring can damage
internal components.
6. Do not place heavy objects on top of the projector.
±12° 360°

Digital Projection MERCURY 5000HD
Power Supply
1. The projector is designed to operate on a power supply of
100-240 V 50/60 Hz AC. Ensure that your power supply fits
this requirement before attempting to use your projector.
2. Handle the power cable carefully and avoid excessive
bending. A damaged cord can cause electric shock or fire.
3. If the projector is not to be used for an extended period of
time, disconnect the plug from the power outlet.
4. Do not touch the power plug with wet hand. Doing so can
cause electrical shock or fire.
5. Do not touch the power plug during a thunder storm. Doing
so can cause electrical shock or fire.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily
soiled, use a mild detergent. Never use strong detergents or
solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful
not to scratch or mar the lens.
CAUTION
Do not unplug the power cable from the wall outlet under any
one of the following circumstances. Doing so can cause
damage to the projector:
• While the message "Please wait a moment." appears. This
message will be displayed after the projector is turned off.
• Immediately after the power cable is plugged into the wall
outlet (the POWER indicator has not changed to a steady
orange glow).
• Immediately after the cooling fan stops working (The cooling
fan continues to work for 90 seconds after the projector is
turned off).
CAUTION
• Do not try to touch the ventilation outlets as they can
become heated while the projector is turned on.
• Do not put the projector on its side when the lamp is turned
on.
Doing so may cause damage to the projector.
• Before shipping this projector, remove the lens and attach
the lens hood cap.
The Lens Shift mechanism may encounter damage caused
by improper handling during transportation.
• Do not eject a PC card or LAN card while its data is being
accessed. Doing so can damage your PC card or LAN card.
Lamp Replacement
• To replace the lamp, follow all instructions provided on page
9-2.
• Be sure to replace the lamp when the message "The Lamp
has reached the end of its usable life. Please replace the
lamp." appears. If you continue to use the lamp after the
lamp has reached the end of its usable life, the lamp bulb
may shatter, and pieces of glass may be scattered in the
lamp case. CAUTION: Do not touch them as the pieces
of glass may cause injury. If this happens, contact your Digital
Projection dealer for lamp replacement.
• Allow a minimum of 90 seconds to elapse after turning off
the projector. Then turn off the main power and disconnect
the power cable and allow 15 minutes to cool the projector
before replacing the lamp.
• The projector must be operated with two lamps installed
regardless of whether or not the lamp is active. Failure to do
so may degrade the performance of the projector such as
screen flicker or loss of lamp life. If one lamp has reached the
end of its usable life, replace it with a new one as soon as
possible.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are
unobstructed to prevent the build-up of heat inside your
projector. Allow at least 3 inches (10 cm) of space between
your projector and a wall, except to the rear and the
ventilation outlet on the right side, where there should be at
least 12 inches (30cm) of space.
2. Prevent foreign objects such as paper clips and bits of paper
from falling into your projector. Do not attempt to retrieve any
objects that might fall into your projector. Do not insert any
metal objects such as a wire or screwdriver into your projector.
If something should fall into your projector, disconnect it
immediately and have the object removed by a qualified
Digital Projection service personnel.
3. Do not place any liquids on top of your projector.
4. When using a LAN cable:
For safety, do not connect to the connector for peripheral
device wiring that might have excessive Voltage.
CAUTION
• Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
• Keep any items such as magnifying glass out of the light
path of the projector. The light being projected from the lens
is extensive, therefore any kind of abnormal objects that can
redirect light coming out of the lens, can cause
unpredictable outcome such as fire or injury to the eyes.
• Do not cover the lens with the supplied lens hood cap or
equivalent while the projector is on. Doing so can lead to
melting of the cap and possibly burning your hands due to
the heat emitted from the light output.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians
in order to ensure proper operation and reduce the risk
of bodily injury.
c. In addition, the ceiling must be strong enough to support
the projector and the installation must be in accordance
with any local building codes.
d. Please consult your dealer for more information.
To Dealer or Installer:
To prevent the projector from falling, install it in a place and
fasten it in a way with sufficient strength to support the
combined weight of the projector (25 kg / 55 lbs), the lens and
any mounting hardware, for an extended period of time as well
as to withstand earthquakes.

Digital Projection MERCURY 5000HD
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your Projector.
NOTE: Lenses are optional. Order lenses from your Digital Projection dealer.
Projector
(102-834)
Remote control (102-161) and
batteries (AAx2)
Remote cable
(102-162)
Power cable for Europe (AC 230V)
(102-163)
Power cable for North America (AC 120V)
(102-165)
Power cable for United Kingdom (AC 230V)
(102-180)
Power cable for Japan (AC 100V)
(102-164)
DVI cable
(102-166)
ON
OFF
ENTER
CANCEL
UNDO
AUTO
HELP
ON
TEST
ABC
1
DEF
2
GHI
3
JKL
4
MNO
5
PQR
6
STU
7
VWX
8
0
YZ
/
9
POWER INPUT
OFF
INFO
PIXEL SOUND OSD
MAGNIFY/
CTL
FOCUS
+
-
ZOOM
+
MENU/
ADDRESS
IMAGE/
PROJECTOR
POSI/
LENS
KEY ST
./
R
E-LIST/
PICTURE
ADJUST
WHITE BAL.
B
AMP/
G
PICT/
SHUT
-
MUTE
Remote cable
(102-162)
DVI cable
(102-166)
User Manual
(103-510)
User Supportware
(102-191)
16Mb PC card
(102-112)
Important Information
(103-511)

Digital Projection MERCURY 5000HD
Optional Lens Installation
This section describes how to install the lens.
Before installation
* Determine the optional lens to be used to obtain a desired projection distance. There are six optional lenses available:
0.64 : 1 fixed part no. 001-734
0.96 : 1 fixed part no. 001-735
1.2 - 1.44 : 1 zoom part no. 001-736
1.44 - 1.8 : 1 zoom part no. 001-737
1.8 - 2.4 : 1 zoom part no. 001-738
2.4 - 3.6 : 1 zoom part no. 001-739
3.6 - 5.6 zoom part no. 001-740
* Press the power button (ON/STAND BY) on the projector or POWER OFF button on the remote control for a minimum of two seconds to turn
off the power, wait 90 seconds for the cooling fan to stop, then disconnect the power cable.
Check that the projector has cooled off sufficiently before proceeding.
CAUTION
* The projector and lens contain high-precision parts. Do not induce shock to the projector or the lens.
* Do not touch the lens surface. Doing so can degrade the optical performance.
Preparation: Tools needed for installation:
A cross head screwdriver.
NOTE: It is possble that the ‘Lens Shift’ feature (described on the previous page and in Section 3. Projecting an Image) may have used to move the
lens mount to the far right side, making installation difficult. If this is the case, then turn the projector back on again and use the Position buttons to
shift the lens back towards the mid-position. When this has been done, turn the projector off as decribed above, before continuing.
1. Remove the rear lens cover, but leave the front cover on to protect the lens surface during installation.
2. Insert the lens into the lens mount with the connector to the right, taking care to line up the locating pin on the lens with the locating hole above
the opening. Push the lens in firmly to engage the connector.
3. Secure the lens using the three cross-head screws.
NOTE. Remove the lens cover before use
locating hole fixing
screws

Digital Projection MERCURY 5000HD
Replacing the Lamp
The projector has two lamps pre-wired into one module,
therefore it is not possible to replace a single lamp. After lamp
1 or lamp 2 has been operating for 1000 hours (Normal mode
using the standard lamp, part number 001-742), the "Lamp"
indicator on the control panel will blink red and a warning
message will appear. Even though the lamp may still be
working, replace it as soon as possible to maintain optimal
projector performance.
CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been used. It
will be extremely hot. Turn the projector off, wait 90 seconds, and
then disconnect the power cable. Allow at least 15 minutes for the
lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except the rear cover screw and
the two lamp module screws. You could receive an electric shock.
• If you continue to use the lamp after 1000 hours, the lamp bulb
may shatter, and pieces of glass may be scattered in the lamp
module. CAUTION: Do not touch them as the pieces of
glass may cause injury. If this happens, contact your Digital
Projection dealer for lamp replacement.
• The projector will turn off and go into stand by mode after 1500
hours of service (Normal mode using the standard lamp - this time
is extended when using Eco mode). If this happens, the lamp must
be replaced.
• The projector contains high-precision parts, so make sure that no
dust or dirt can get into the cabinet during lamp replacement. Clean
the outside of the cabinet before opening the rear cover.
To replace the lamp module:
1. Loosen the rear cover fastening by turning it through 45° and open
the cover, using the support if the projector is upside down.
NOTE: There is an interlock on the rear cover to prevent the risk of
electrical shock. Do not attempt to circumvent this interlock.
2. Squeezing the plug latch firmly, unplug the lamp control cable from the
connector at the rear of the lamp module.
4. Pull the lamp module to the right, then to the rear to remove it from
the projector.
5. Insert a new lamp module, manoeuvreing it carefully so that the plug
on the top of the module mates properly with the socket in the roof of
the cabinet.
CAUTION: Do not use a lamp other than the Digital Projection
replacement lamp (Standard life lamp: 001-742).
6. Secure it in place with the two screws.
Be sure to tighten the screws.
7. Re-connect the lamp control cable to the connector at the rear of the
lamp housing.
8. We recommend that you clean or change the filter, as described on
the next page, whenever the lamp is changed.
9. Close the rear cover firmly, ensuring that the catch clicks shut.
NOTE: Installing a new lamp module automatically clears the lamp usage
hours, as the lamp memory chip is built-in to the module. You can check
the current lamp useage hours via the Projector Information Menu.
3. Loosen the two screws securing the lamp module until the screws go
into a freewheeling condition. The two screws are not removable.
Cover
Support

Digital Projection MERCURY 5000HD
Replacing or Cleaning the Filter
The air-filter prevents dust or dirt from getting inside the
projector and should be cleaned after every 100 hours of
operation (more often in dusty conditions). If the filter is dirty
or clogged, your projector may overheat.
NOTE: The message "Please clean the filters" will be displayed each
time the projector is turned on after it has been used in excess of 168
hours. Should this message appear, clean the filters as a matter of
urgency.
CAUTION
• Turn the projector off, wait 90 seconds, and then disconnect the
power cable, before cleaning the filter.
• Do not attempt to operate the projector without a filter.
• The projector contains high-precision parts, so make sure that no
dust or dirt can get into the cabinet during filter replacement. Clean
the outside of the cabinet before opening the rear cover.
To replace or clean the filter:
1. Loosen the rear cover fastening by turning it through 45° and open
the cover, using the support if the projector is upside down.
NOTE: There is an interlock on the rear cover to prevent the risk of
electrical shock. Do not attempt to circumvent this interlock.
2. Remove the single cross-headed screw securing the top edge of the
filter, and remove the filter.
Cleaning the Cabinet and the Lens
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,
use a mild detergent. Never use strong detergents or solvents such
as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens.
Filter
3. If the filter is severely clogged, or damaged, then it should be
replaced.
NOTE: Do not wash the filter with water, as this will damage the filter
membrane.
4. Clean the filter using a vacuum cleaner.
5. Install the new or cleaned filter by first locating the bottom edge into
the recess, then hinging the filter upwards. Secure the filter by
replacing the screw.
6. Close the rear cover firmly, ensuring that the catch clicks shut.
NOTE: After the filter has been changed, the message "Please clean
the filters" will continue to be displayed until the Filter Usage Meter has
been cleared
7. Following the instructions in Section 8, go to Page 5 in the Projector
Setup menu, and press the button marked “Clear Filter Usage Meter”.
Screw
Cover
Support

Digital Projection MERCURY 5000HD
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Power Indicator
Indicator Condition Projector Condition Note
Off
Blinking light
Steady light
Green blinking
Orange blinking
0.5 sec ON,
0.5 sec OFF
2.5 sec ON,
0.5 sec OFF
0.5 sec ON,
0.5 sec OFF
2.5 sec ON,
0.5 sec OFF
The main power is off
The projector is getting ready to turn on.
Off Timer or Sleep Timer is active.
The projector is cooling down.
On Timer is active.
The projector is turned on.
The projector is in Standby or Idle.
Green
Orange
–
Wait for a moment.
–
Wait for a moment.
–
–
–
Indicator Condition Projector Condition Note
Off
Blinking light
Steady light
Red blinking
Red
Orange
Green
1 cycle (0.5 sec ON,
2.5 sec OFF)
2 cycle (0.5 sec ON,
0.5 sec OFF)
3 cycle (0.5 sec ON,
0.5 sec OFF)
4 cycle (0.5 sec ON,
0.5 sec OFF)
Normal
Lens hood or lamp cover error
Temperature error
Power error
Fan error
Circuit error
Control key locked
Idle condition
–
Replace the lens hood or the lamp
cover correctly.
The projector is overheated. Move
the projector to a cooler location.
Power unit will not work correctly.
Cooling fan has stopped. Contact
your dealer.
A circuit has failed. Contack your
dealer
You have pressed control panel key
when Control Key Lock is enabled.
–
Status Indicator
Indicator Condition Projector Condition Note
Off
Blinking light
Steady light
Light off
Lamp has reached its end of life. Lamp
replacement message will be displayed.
No lamp
Lamp error
Lamp data error
Re-firing the lamp
Switching from Lamp 1 to 2
Lamp has been used beyond its
limit. The projector will not turn on
until the lamp is replaced.
Lamp mode is set to Normal mode
Lamp mode is set to Eco mode.
Red blinking
Green blinking
Orange blinking
Red
Green
Orange
–
Replace the lamp.
Lamp is not installed. Turn off the
power and install lamp.
Lamp fails to light. Wait a full minute and
turn on the power again. If this will not
solve the problem, consult your dealer.
Fails to read lamp data.
Consult your dealer.
Wait for a moment.
Wait for a moment.
Replace the lamp.
–
–
Lamp 1/2 Indicator
2.5 sec ON,
0.5 sec OFF
1 cycle (0.5 sec ON,
2.5 sec OFF)
6 cycle (0.5 sec ON,
0.5 sec OFF)
7 cycle (0.5 sec ON,
0.5 sec OFF)

Digital Projection MERCURY 5000HD
Does not turn on
No picture
Image isn’t square to
the screen
Picture is blurred
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or blink-
ing
Cross color in RGB
mode
USB mouse does not
work
No on-screen menu
• Check that the power cable is plugged in. See pages 1-9 and 2-11.
• Ensure that the rear cover is installed correctly. See pages 1-4 and 9-2.
• Check to see if the projector has overheated or the lamp has reached the end of its usable life.
If there is insufficient ventilation around the projector or if the room where you’re presenting is
particularly warm, move the projector to a cooler location.
• Use the menu or Source/Input button to select your source (RGB 1/2, DVI, Video, S-Video,
Viewer or LAN). See page 3-3 or 8-7.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page 8-8.
• Select correct option in the Signal Select for current signal. See page 8-16.
• Select RGB/Component when connecting DVD player to RGB connector of the projector. See
page 8-11.
• Apply a standard RGB signal when using RGB connector.
• Adjust picture for RGB signal.
• Make sure each setting is correct.
• If the problem still persists, reset the settings or adjustments to factory preset levels using the
Factory Default in the Adjustment Menu. See page 8-13.
• If Security is enabled, a keyword or PC card as a protect key is required.
• Remove the lens cap.
• Reposition the projector to improve its angle to the screen. See page 3-3.
• Use the 3D Reform function to correct the trapezoid distortion. See page 3-4.
• Adjust the focus. See page 3-4.
• Reposition the projector to improve its angle to the screen. See page 3-3.
• Ensure that the distance between the projector and screen is within the adjustment range of the
lens. See page 2-2.
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then
turned on. Should this happen, let the projector stand until there is no condensation on the lens.
• Use the menus or Source/Input button on the remote control or the cabinet to select the source
you want to input. See page 3-3 or 8-7.
• Install new batteries. See page 1-12.
• Make sure there are no obstacles between you and the projector. See page 1-12.
• Stand within 22 feet (7 m) of the projector. See page 1-12.
• Check if one or more remote sensors are enabled. Select [Projector Options] →[Setup] →[Page
5] →[Remote Sensor] from the menu. See page 8-17.
• If the remote control cable plug is inserted into the REMOTE 2 IN jack, the remote control does not
function wirelessly. See page 1-13.
• Make sure that the remote control’s ID corresponds with the projector’s ID. See page 7-2.
• See the Power/Status/Lamp Indicator on page 10-3.
• If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock in the Image
Options. See page 8-16.
• Make sure that your USB mouse is properly connected to the projector.
The projector may not support some brands of a USB mouse.
• Press MUTE OSD if the image is muted. Or press and hold CTL and press MUTE OSD button. See
page 4-2.
Problem Check These Items
Common Problems & Solutions

Digital Projection MERCURY 5000HD
Specifications
Part Number 102-834
Optical
Digital Light Processor Texas Instruments DMD™, native resolution 1280 x 720
Lamp Standard Lamp (Part No. 001-742) 250 W AC x2
Lamp Life (typical) Normal mode 1500 hours
Lens Options Motorized zoom and Motorized focus
0.64 : 1 fixed part no. 001-734
0.96 : 1 fixed part no. 001-735
1.2 - 1.44 : 1 zoom part no. 001-736
1.44 - 1.8 : 1 zoom part no. 001-737
1.8 - 2.4 : 1 zoom part no. 001-738
2.4 - 3.6 : 1 zoom part no. 001-739
3.6 - 5.6 zoom part no. 001-740
Lens Shift zoom lenses: Vertical +0.5 -0.16 Height, Horizontal +/-0.1 Width
fixed lenses: cannot be shifted without losing corners of image
Image Size 0.64 : 1 fixed 60” - 150” diagonal
0.96 : 1 fixed 60” - 400”
1.2 - 1.44 : 1 zoom 60” - 200”
1.44 - 1.8 : 1 zoom 60” - 250”
1.8 - 2.4 : 1 zoom 60” - 400”
2.4 - 3.6 : 1 zoom 60” - 300”
3.6 - 5.6 zoom 60” - 240”
Projection Distance 0.64 : 1 fixed 1.0m - 2.3m (3ft 3in - 7ft 5in)
0.96 : 1 fixed 1.4m - 8.6m (4ft 7in - 28ft 3in)
1.2 - 1.44 : 1 zoom 1.7m - 6.5m (5ft 6in - 21ft 3in)
1.44 - 1.8 : 1 zoom 2.0m - 10.0m (6ft 5in - 32ft 10in)
1.8 - 2.4 : 1 zoom 2.4m - 21.3m (8ft - 70ft)
2.4 - 3.6 : 1 zoom 3.2m - 24.0m (11ft - 79ft)
3.6 - 5.6 zoom 4.8m - 29.8m (16ft - 98ft)
Electrical
Input Connections RGB/YCr/Cb/H(HV)V 5 BNCx1, Audio: RCA (L/MONO, R)x1
RGB D-Sub 15 pin x1, Audio: Stereo Mini Audio x1
DVI DIGITAL DVI-D (Max resolution : XGA@60Hz) x1, Audio: Stereo Mini Audio x1
Video BNC x1, Audio: RCA (L/MONO, R) x1
S-Video Mini DIN 4 x1, Audio: RCA (L/MONO, R) x1
PC Card Slot x2
Option Board Slot x2
Output Connections RGB D-Sub 15 pin x1
Audio Out RCA (L/MONO, R) x1
Other Input/Output Remote Control Stereo mini jack ;IN x 1; OUT x1
PC Control D-Sub 9 pin; IN x1, OUT x1
Ex. Control D-Sub 15 Din x1
SC. TRIGGER Stereo mini jack x1
LAN Port RJ-45 x1
USB Port A Type x1, B Type x1

Digital Projection MERCURY 5000HD
For additional information visit:
US: http://www.digitalprojection.com
Europe: http://www.digitalprojection.co.uk/
Asia: http://www.digitalprojection.co.uk/
The specifications are subject to change without notice.
Input Compatibility NTSC / PAL / PAL60 / SECAM / NTSC4.43, YCbCr Component, HDTV-1080I, 1080p, 720p, 480p,
480I, VGA, SVGA, XGA, SXGA / UXGA (with Advanced AccuBlend)
Sychronization Horizontal Frequency : 15 - 100 kHz (RGB : 24 kHz or over)
Range Vertical Frequency : 48 - 120 Hz
Video Bandwidth RGB: 100 MHz
Color Reproduction Full color, 0.5 trillion colors simultaneously
Horizontal Resolution 550 TV lines : NTSC / PAL / NTSC4.43 / YCbCr
350 TV lines : SECAM
RGB: 1024 dots horizontal, 768 dots vertical
Power Requirement 100 - 240 VAC, 50 / 60 Hz
Input Current 10.0 A (100 VAC) / 4.0A (240 VAC)
Power Consumption 1000W (Dual Lamp mode)
750W (Single Lamp mode)
< 1W (Standby)
Mechanical
Dimensions 531 mm (W) x 270 mm (H) x 535 mm (D) / 20.9" (W) x 10.7" (H) x 21.1" (D) (not including protrusions)
Net Weight 25 kg / 55 lbs (not including lens)
Environment Operational Temperatures: 32° - 95°F (0° to 35°C), 20 - 80% humidity
Storage Temperatures: 14° - 122°F (-10° to 50°C), 20 - 80% humidity
Regulations Meets FCC Class A requirements
Meets EMC Directives (EN 50081-1, EN 50082-1, EN 55022, EN 60950)
Meets Low Voltage Directive (EN60950)